TRENDnet TEW-840APBO Manuale utente

TEW-840APBO (V1)

Quick Installation Guide

Table of Contents

2. Hardware Setup and Configuration

3. Hardware Installation

1 English

1. Before You Start

Package Contents

ŸProprietary/Passive PoE injector (24V DC, 0.6A)

ŸMounting Hardware

Minimum Requirements

ŸComputer with a network port and web browser

ŸA network switch or router with an available network LAN port

ŸAdditional TEW-840APBO H/W: v1.xR wireless AC867 directional access point

Ÿ4 x RJ-45 network cables

ŸTEW-840APBO

ŸQuick Installation Guide

Note:

The TEW-840APBO does not support IEEE 802.3at/af PoE standards. You must use the

proprietary/passive power over Ethernet injector that is supplied with the TEW-840APBO. This

installation guide will walk you through the installation and configuration of two TEW-840APBO

access points to establish a wireless point to point bridge using WDS (wireless distribution

system). The RJ-45 Ethernet cable between the passive PoE injector and access point can have

a maximum length of up to 60 m (197 ft.).

ENGLISHFRANÇAIS

ESPAÑOL

2. Hardware Setup and Configuration

Phase 1: Overview

In this installation guide, we will assume the following:

The TEW-840APBO access points will be configured with the following settings:

Router Settings:

Router/Default Gateway IP address: 192.168.10.1

Subnet Mask: 255.255.255.0

TEW-840APBO #1

IP Address: 192.168.10.50

Netmask (Subnet Mask): 255.255.255.0

IP Gateway (Default Gateway): 192.168.10.1

Primary DNS: 192.168.10.1

Wireless Channel Default: 48

WDS Access Point Mode (CSMA)

WPA2-PSK Encryption

WDS Station Mode (CSMA)

TEW-840APBO #2

WPA2-PSK Encryption

IP Address: 192.168.10.51

Netmask (Subnet Mask): 255.255.255.0

IP Gateway (Default Gateway): 192.168.10.1

Primary DNS: 192.168.10.1

Wireless Channel Default: 48

Note:

Ÿ Configure and connect the access points before mounting.

Ÿ The initial configuration should be completed in a testing environment with two

TEW-840APBO access points approximately 15 ft. (5 m) apart from one another with the

front of the access points directly facing each other.

Ÿ The configuration example in this guide will use the default/standard TEW-840APBO channel

access mode CSMA. More details can be found in the user's guide about TDMA channel

access mode which is also supported by the TEW-840APBO wireless AP.

Ÿ The default IP address of the TEW-840APBO is 192.168.10.100. To configure the

TEW-840APBO, your network adapter must have an IP address within the 192.168.10.x

subnet (e.g. 192.168.10.10). Please refer to the Appendix in the User's Guide for more

information.

Phase 2: TEW-840APBO Unit #1 Hardware Setup and Configuration

1. Remove the cover of the access point by pulling and holding the bottom tab in the vertical

direction down (based on the access point orientation below) and sliding the cover below

away from the access point.

Pull and hold tab

ENGLISHFRANÇAIS

ESPAÑOL

2. Write down the SSID and WPA2 Key of the TEW-840APBO #1 access point. The SSID and

WPA2 Key can be found on the inside of the device cover where the Ethernet LAN ports are

located (shown below).

3. Using a network cable, connect one end of the cable to the LAN1 (PoE) port.

Model: TEW-840APBO /A

IP Address: 192.168.10.100

Subnet Mask: 255.255.255.0

User Name: admin

Password: admin

Mode: WDS AP

SSID: TRENDnet840_XXXX

WPA2 Key: 840XXXXXXXX

Default Channel: 48

Cable Guide

LAN2 LAN1 (PoE)

PWR LAN1 LAN2 WLAN

TEW-840APBO

FCC ID: XU8TEW840APBO

IC ID: 6337A-TEW840APBO

LAN2 LAN1 (PoE)

PWR LAN1 LAN2 WLAN

TEW-840APBO

FCC ID: XU8TEW840APBO

IC ID: 6337A-TEW840APBO

Included PoE injector

LAN1 (PoE)

PoE LAN

9. Assign a static IP address to your computer's network adapter in the subnet of

192.168.10.x (e.g. 192.168.10.10) and subnet mask of 255.255.255.0.

4. Connect the other end of the network cable to the PoE port on the included PoE injector.

5. Using another network cable, connect one end to the LAN port on the included PoE injector.

6. Connect the other end of the network cable to your computer's Ethernet port.

7. Attach the power cord to the PoE injector and plug the connected power cord into a power

outlet.

8. Confirm the device is powered on through the LED indicators.

10. Open your web browser and type the IP address of the access point in the address bar, then

press Enter. The default IP address is 192.168.10.100.

POWER

ENGLISHFRANÇAIS

ESPAÑOL

11. When prompted, login to the browser configuration page using the default user name and

password settings.

User Name: admin

Password: admin

Note: User Name and Password are case sensitive.

12. In the left hand menu under System Manager, click on Account.

13. Under Account Settings, change the default administrator password by typing in the

current password admin and your new password in the fields provided. Then click the

Apply button the save the new password settings. You will prompted to log back in with

the new password settings.

14. After setting a new administrator password, in the left hand menu under Network, click on

Basic.

15. In the IPv4 Settings section, enter the IP Address 192.168.10.50 and Subnet Mask

255.255.255.0, then click Save at the bottom of the page. When prompted to apply settings

at the bottom right of the page, click Apply to commit the changes.

Note: When configuring TEW-840APBO #2, enter the IP address settings 192.168.10.51 and

Netmask 255.255.255.0.

ENGLISHFRANÇAIS

ESPAÑOL

Phase 3: TEW-840APBO Unit #2 Hardware Setup and Configuration

When configuring the TEW-840APBO #2, repeat 1-14 of the steps in Phase 2 setup and

configuration.

1. In Step 15, under , enter the IP Address 192.168.10.51 and IPv4 Settings Subnet Mask

255.255.255.0, then click Save at the bottom of the page. When prompted to apply settings

at the bottom right of the page, click Apply to commit the changes.

2. In the left hand menu under Network, click Wireless.

3. Under 5GHz-802.11 AC/N, click the Operation Mode drop-down list and select WDS

Station.

Altri manuali per TEW-840APBO

Altri manuali TRENDnet Router di rete

TRENDnet

TRENDnet TE100-S16Eg Manuale utente

TRENDnet

TRENDnet TE100-S16R Manuale utente

TRENDnet

TRENDnet TEW711BRV2 Manuale utente

TRENDnet

TRENDnet WLAN ADSL2 plus Router Manuale utente

TRENDnet

TRENDnet THA?101 Manuale utente

TRENDnet

TRENDnet TEW-631BRP Manuale utente

TRENDnet

TRENDnet TW100-BRV304 SHEETS Manuale utente

TRENDnet

TRENDnet TPL-202E - Powerline Fast EN Bridge Manuale utente

TRENDnet

TRENDnet TEW 632BRP - Wireless Router Manuale utente

TRENDnet

TRENDnet TW100-BRV214 Manuale utente

TRENDnet

TRENDnet TEG-S5g - Gigabit GREENnet Switch Manuale utente

TRENDnet

TRENDnet TW100-BRV204 SHEETS Manuale utente

TRENDnet

TRENDnet TE100-S50g Manuale utente

TRENDnet

TRENDnet TW100 TW100-BRV304 Manuale di installazione e funzionamento

TRENDnet

TRENDnet TW100-BRV304 SHEETS Manuale utente

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Manuale utente

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Manuale utente

TRENDnet

TRENDnet TEG-448WS - Switch Manuale utente

TRENDnet

TRENDnet TWG-BRF114 Manuale utente

TRENDnet

TRENDnet TW100-BRM504 Manuale utente

TRENDnet

TRENDnet TDM-C500 Manuale utente

TRENDnet

TRENDnet TEW-731BR Manuale utente

TRENDnet

TRENDnet TEW-733GR Manuale utente

TRENDnet

TRENDnet TE100-S88 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza