Triax PSU 249/8 Manuale utente
Model Item no.
PSU 249/8 301082
Version EN triax.com
PSU 249/8
12VDC 18 Port , 12 Amp PTC Protection
2.1 PSU 249/8 power supply must be used with 230VAC ±10% 50Hz mains supply.
2.2 The output voltage is 24VAC with an output power of 192W..
2.3 The power supply has the following protection functionality: Over-current and short
circuit protection.
2.4 The rated input voltage of the switch mode power supply is 230VAC ±10% 50Hz.
2.5 Operating Temperature -10and +30°C
3.1 Remove the power supply from the packaging and check for any damage that may
have occurred in transit. If the power supply is damaged DO NOT Use and return to
your Supplier.
3.2 Make sure that the Incoming mains supply is turned off at the circuit breaker and that
the power supply is also switched off
3.3 Install the power supply in a suitable location free from moisture and dust.
The power supply can be mounted on to a wall.
Step 1: Use the template provided to accurately mark out the hole locations
Step 2: Drill 4 x M4 holes and insert Rawl plugs (not supplied)
Step 3: Align power supply up with the holes and insert the 4 screws, ensure that
the power supply is level prior to fully tightening the screws.
3.4 Connect mains supply cables in accordance to BS 7671 17th Edition Wiring
Regulations,ThispowersupplymustbeinstalledbyasuitablyqualiedElectricianor
competent Person.
3.5 Whilst the Power supply is switched OFF, connect all Cameras to the desired output
pair, which is individually protected by a fuse. Refer to drawings.
3.6 Once the installation of the wiring and connection of the cameras is complete, turn
on the mains supply and then the Power supply. When the power supply is switched
ON a RED LED will illuminate.
3.7 The input fuse rating is 250VAC/4A
1.1 Read the manual carefully before use.
1.2 The switching power supply shall be installed according to the installation instruction.
1.3 For indoor use only. Do not use this equipment near water.
1.4 Please follow the required power rate from power label. In case of any questions
please refer to the equipment.
1.5 ACpowercableplugwith3pins,thethirdpinforgrounding.Usethequalication
power cord to operate and make sure the connection as the safety condition.
1.6 Do not overload the power supply.
1.7 Make sure the power is OFF during installation.
1.8 Servicing – Do NOT attempt to service the product yourself. Removing covers can
expose you to electric shock and other dangerous conditions. Maintenance should be
performedbyasuitablyqualiedpersononly.
2. Product Features
1. Important Safety Instructions
3. Installation
Triaxreservestherighttochangethespecicationswithoutpriornotication.
Triax accepts no liability in respect of loss arising from errors
in changes to the information provided.
4. TechnicalSpecications
4.1 Input Voltage: 230VAC ±10% 50Hz
4.2 Output Voltage 24VAC
4.3 Total output Current: 8 Amps max
4.4 Total output Power: 192W
4.5. Dimensions: 279x215x93mm
4.6 Weight: 4.5 Kg
Copyright © 2016 TRIAX. All rights reserved. The TRIAX Logo and TRIAX, TRIAX Multimedia
are registered trademarks or trademarks of the TRIAX Company or its afliates.
All specications in this guide are subject to change without further notice.
TRIAX A/S | Bjørnkærvej 3 | DK-8783 Hornsyld | Denmark
triax.com/support
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Triax Alimentazione elettrica
