Trimec 310 Series Manuale utente
IMPORTANT NOTE: Ensure any rebate strips or door stops are fitted before proceeding.
For double-leaf doors, the inactive leaf must be securely fixed in the closed position and a rebate strip fitted to prevent
door over-travel.
Strike is suitable for 15mm latches, based on a 3mm door gap.
INSTALLATION INSTRUCTIONS
310/3100/320/3200 SERIES ELECTRIC STRIKE
Mark positions X and Y of door latchbolt on door jamb (see Fig. 1).
Remove the backing of supplied stick-on template, and apply to door jamb. Ensure the lines “Front face of Lock Latch” on both template
and door jamb are aligned (see Note 1).
Scribe the door jamb according to template outline (see Fig. 2).
Prepare door jamb as per appropriate strike face plate, as shown in Fig. 3. Install mounting tabs where applicable. (see Note 2).
Ensure all wiring is correctly connected and not rubbing on sharp edges or interfering with any strike mechanism.
Install the strike temporarily in position and check there is no interference between the door, strike and lock face plates, and the extension
lip of strike during door closing. Ensure the deadlatching auxiliary bolt does not enter the strike keeper area when door is closed.
Check there is no pressure on the strike keeper when door is closed.
When all above checks are complete, secure strike with appropriate screws and re-check operation.
NOTE 1 : A 1mm clearance has been designed into the template to prevent the door exerting pressure on the strike when closed.
NOTE 2 : Allow sufficient space between the electric strike unit and jamb cut-out for the wires. Bunching of wires may cause the unit to
malfunction.
1.
2.
3.
4.
5.
6.
7.
8.
Fig. 2 - 310 / 3100 / 320 / 3200 Series Electric Strike Template Outline
Fig. 1 - Door Frame Preparation
Align with
“Front Face
of Lock
Latch” line
on Template
y
x
y
X
X
y
or
Bevelled Face
*These dimensions have a tolerance of +0.8mm/-0
Template outline may vary depending on strike face plate used.
P
age
1
DRAWINGS NOT TO SCALE. INFORMATION IN THIS DATASHEET MAY BE CHANGED WITHOUT NOTICE.
P
age
4
310/3100/320/3200 SERIES
The following are available as optional extras:
SPARE PARTS
* When the use of extension lips is required, the standard model numbers of electric strikes must be suffixed with “X” to denote
pre-drilled extension holes (e.g. 3100X).
25mm extension lip (A),
50mm extension lip (B)
75mm extension lip (C)
available as optional extras.
B
50mm
A
25mm 75mm
C
xx
yy
Door Edge
or
Mortice Lock Tubular/Cylindrical
Latch
Part Number Qty Per Pack Description
220200-501 1 Strike Status Microswitch Assembly
220200-502 1 Door Latch Microswitch Assembly
220200-504 1 set Screw Kit - Installation
220200-508 5 x (2 short, 1 long) Locking Pins
220200-509 5 Spring - For Striker
220200-511 5 Spring - Locking Pin
220200-520 5 Spring - Microswitch Retainer
220200-513 1 12 V Solenoid Coil
220200-514 1 24 V Solenoid Coil
220200-515 1 48 V Solenoid Coil
ACCESSORIES
Part Number Qty Per Pack Description
220200-519 1 Mounting Kit
5 Year Limited Warranty
ASSA ABLOY Australia guarantees for a period of 5 years in accordance with Trimec’s Standard Warranty Conditions, against defects in
manufacture, workmanship or materials, provided that all electrical and mechanical installation requirements are adhered to as per this
datasheet. All third party and consequential claims are expressly excluded from this warranty.
warranty
An ASSA ABLOY Group brand
DA0014, Issue 8: 16th Feb 2007
ASSA ABLOY Australia
2/16 Atkinson Road
Taren Point 2229
NSW, Australia
www.assaabloyasiapacific.com
SPARE PARTS & ACCESSORIES
Front Face of Lock Latch
NOT TO SCALE
310/3100 Series
Limits of Extension Lip (ANSI)
61mm
*36.5mm
*47.5mm
Keeper Width
38mm
*201.5mm
310/3100 Series *86mm
320/3200 Series Limits of Extension Lip (Wide) 100mm
320/3200 Series *123mm
185.5mm
EXTENSION LIPS* & STRIKE FACE PLATES
For a wide range of extension lips and strike face plates to suit a particular application, please contact your nearest distributor.
To change the electric strike’s mode of lock operation, remove the back cover and the 2 screws securing the solenoid.
Remove solenoid from strike housing, and invert the strike. This will release three locking pins from the strike and keeper chambers.
CAUTION! When removing solenoid, please be mindful to keep the plunger in the solenoid as it is not secured, and may be easily mis-
placed.
Re-insert the pins as shown in the diagrams for desired mode of lock operation (Power to Open: see Fig. 4; Power to Lock: see Fig. 5).
Place solenoid back in strike housing, and secure with solenoid screws. Press strike back cover into position.
1.
2.
3.
4.
P
age
2
P
age
3
Solenoid Leads Colour
Red
Blue
Black
Supply Voltage
12 VDC
24 VDC
48 VDC
Current Draw
175 mA
88 mA
45 mA
CAUTION! Incorrect supply voltage may cause damage not covered by warranty. Please check supply voltage with a suitable meter
to ensure it is within +/- 15% of the nominal voltage shown above with the strike powered.
This product has been designed for use in weather protected areas only. DO NOT OIL OR LUBRICATE.
3100 / 3200 Series Microswitch Monitoring
The 3100 / 3200 Series electric strike is fitted with a UL approved changeover microswitch (max. rating: 125 VAC, 3 A / 60 VDC, 200 mA)
to monitor the latch and strike status. The wiring diagram for the monitoring schematic is shown in Fig. 6 and on the back of the strike.
N.C. (Normally Closed)
Common
N.O. (Normally Open)
White
Orange
Grey
Strike
Common
N.O. (Normally Open)
Yellow
Violet
Brown
Latch
N.C. (Normally Closed)
Certification
AS4145.2 compliant
BS5872 approved
CE compliant
up to 4-hours fire rating, depending on type of doorset
(in accordance with AS1905.1 - 1997, Part 1: Fire-resistant Doorsets)
Wiring methods and materials shall be in accordance with the National Electric Code, ANSI/NFPA 70 - 1996
Unit must be powered by a UL listed limited energy power source
Use only those mounting screws and hardware supplied with the product for installation. Do not use substitute installation fasteners or
hardware
UL listed for burglary resistance category 1034
Standard UL 1034 Tested and Listed for:
1,500 lbs. (680 kg) static strength rating
70 foot-lbs. dynamic strength rating
250,000 cycles endurance rating
At the request of ASSA ABLOY Australia, this model was tested to the following VOLUNTARY ratings:
1,000,000 cycles of operation
•
•
•
•
•
•
•
•
•
•
•
•
4
Hour
UL Listing
Fig. 4 - Power To Open (Fail-Safe) Configuration
Fig. 5 - Power To Lock (Fail-Secure) Configuration
Solenoid
Plunger
Solenoid Leads
Strike Body
Locking Pins
(Long - Short - Short)
Pin Chamber
Locking Pins
(Short - Short - Long)
Solenoid
Plunger
Solenoid Leads
Strike Body
Pin Chamber
24mm
3100 series strike shown
Mounting tabs
CHANGING MODE OF LOCK OPERATION
ELECTRICAL SPECIFICATIONS
Fig. 3 - Door Jamb Installation
Fig. 6 - Monitoring Schematic
Fig. 6 - Monitoring Schematic
Questo manuale è adatto per i seguenti modelli
13
Altri manuali Trimec Serratura
