Triminator Rosin TRP stack Manuale utente
®
RosinTRPstack
OWNER'S MANUAL
V 1.4
CONTENTS
INTRODUCTION............................................................... 2
SAFETY MESSAGES ....................................................2
ROSIN PRESS SAFETY ................................................... 3
IMPORTANT SAFETY INFORMATION .........................3
SAFETY LABEL LOCATIONS........................................... 4
CONTROLS AND COMPONENTS.................................... 5
STARTING THE ROSIN PRESS ....................................... 7
ROSIN PRESS OPERATION ............................................ 8
PID TROUBLESHOOTING................................................ 9
LIMITED WARRANTY...................................................13
EXCLUSIONS FROM WARRANTY COVERAGE ...........14
CUSTOMER SERVICE................................................ 14
INTRODUCTION
Congratulations on your selection of the Triminator Rosin TRP Stack! We want to help you to get
the best results from your new press and to operate it safely. This manual contains the informa-
tion on how to do that; please read it carefully before you set up and use your rosin press.
We suggest you read the LIMITED WARRANTY (page 13) to fully understand coverage and your
responsiilities of ownership. Keep this owner’s manual handy, so you can refer to it at any time.
This owner’s manual is considered a permanent part of the rosin press and should remain with
the press if resold. The information and specifications included in this publication are those that
were in eect at the time of approval for printing. Mosman Machinery Company, Inc. reserves
the right, however, to discontinue or change specifications or design at any time without notice
and without incurring any obligation whatsoever. No part of this publication may be reproduced
without written permission.
SAFETY MESSAGES
Your safety and the safety of others are very important. We have provided important safety
messages in this manual and on the Triminator. This information alerts you to potential hazards
that could hurt you or others. Please read these messages carefully. Of course, it is not practical
or possible to warn you about all the hazards associated with operating or maintaining a hydrau-
lic press. You must use your own good judgment.
You will find important safety information in a variety of forms:
Safety Labels - located on the rosin press.
Instructions - how to use this rosin press correctly and safely.
Safety Messages - preceded by a safety alert.
A symbol and one of two signal words: DANGER, CAUTION. These signal words mean:
Each message tells you what the hazard is, what can happen, and what you can do to avoid inju-
ry.
Damage Prevention Messages - You will also see other important messages that are preceded by
the word NOTICE. This word means:
2
DANGER
!CAUTION
You WILL be KILLED or SERIOUSLY HURT
if you don’t follow instructions.
You CAN be KILLED or SERIOUSLY HURT if
you don’t follow instructions.
NOTICE Your rosin press or other property can be dam-
aged if you don’t follow instructions.
ROSIN PRESS SAFETY
IMPORTANT SAFETY INFORMATION
Triminator rosin presses are designed to extract essential elements from plants containing resin
glands utilizing heat and pressure and from a variety of herbal material. Other uses could result
in injury to the operator or damage to the rosin press and or other property. Injuries and prop-
erty damage arising from the use of the Triminator rosin press can be prevented by following
all instructions in this manual and on the rosin press. The most common hazards are discussed
below, along with the best way to protect yourself and others.
OPERATE ON FLAT SURFACE
To avoid overturning, only operate the rosin press on flat, hard, durable surfaces. Preferably at
table height or higher for best access and operator visibility. Press is heavy and must be posi-
tioned on a flat surface so as to prevent any accidental upset or tip-over.
AVOID CONTACT WITH HEAT PLATENS
Heat platens can operate at temperatures up to 225 degrees fahrenheit. Prolonged contact can
cause serious burns. Note red indicator light on power button indicating power ON and platens
hot.
TURN ELECTRIC POWER OFF AND UNPLUG WHEN NOT OPERATING THE ROSIN PRESS
If you need to leave the rosin press for any reason, always turn electric power o.
MANUAL HYDRAULIC PUMP
Do not place fingers or other body parts in area between heat platens when hand pumping hy-
draulic pump. Pinching or crushing injuries could result.
AIR OR ELECTRIC HYDRAULIC POWER OPTIONS
Do not place fingers or other body parts in area between heat platens.
Keep BOTH hands on power unit contols at all times when hydraulicly closing press platens.
All rosin press loading and closing functions are to be activated by a single person operator ONLY.
OPERATOR RESPONSIBILITY
Know how to stop and reverse press action immediately in case of emergency. Understand the
use of all rosin press controls. Never permit anyone to operate the rosin press without proper
instruction. Do not let children operate the rosin press.
3
3
SAFETY LABEL LOCATIONS
4
The labels shown here contain important safety information. Please read them carefully.
These labels are considered a permanent part of your rosin press. If a label comes o or be-
comes hard to read, promptly contact your authorized Triminator dealer for a replacement.
CONTROLS AND COMPONENTS
PID Temperature Gauge
Controls temp for each
platen.
Power Button
Aluminum Platens
6 inch by 10 inch with two
heating elements per plat-
en.
Hydraulic Cylinder
Steel Frame
Cast in NorCal.
Drip Tech Handle
Pull down & up to
operate.
Hose Interface
Connect pump to hy-
draulic cylinder with
hose interface.
Drip Tech Pivot
See graphic at
bottom of page
Drip Tech Pivot
View of machine piv-
oted to allow rosin to
fall below.
5
BEFORE OPERATION
Read and understand this manual. Know what the controls do and how to operate them.
Familiarize yourself with the rosin press and its operation before you begin using it. Know
how to quickly shut o the machine in case of an emergency.
Your safety is your responsibility.
IS YOUR ROSIN PRESS READY FOR OPERATION?
For your safety, and to maximize the service life of your equipment, it is very important to
take a few moments each time before you operate the press to check its condition. Be sure
to take care of any problem you find before you operate the rosin press.
Improperly maintaining this rosin press, or failing to correct a problem before operation,
could cause a malfunction which could cause you to be seriously injured.
Always perform a pre-operation inspection before each operation, and correct any problem.
Before beginning your pre-operation checks, be sure the rosin press is on a level surface,
the power button is in the OFF position, and power cord is unplugged.
CHECK THE GENERAL CONDITION OF THE ROSIN PRESS
Check each control for proper operation.
Check parts for wear. Replace if necessary.
Check that all nuts, bolts, and clamps are tightened appropriately.
OPERATING THE DRIP TECH PIVOT SYSTEM
To operate the Easy Pivot Drip Tech system, pull down the on the Drip Tech handle on the
top of the machine.
CONTROLS AND COMPONENTS (CONT)
65
STARTING THE ROSIN PRESS
7
CONNECT POWER CORD
Connect the Rosin Press power cord to a 20A 120V AC circuit. Optional air or electric power
units may be plugged in to the same outlet. Do not connect and disconnect the power cord
with wet hands. Do not operate in the rain.
NOTICE
Rosin Press machine alone draws approximately 15 amps. With optional electric power
unit, total current draw will be approximately 30 amps.
ATTACH HYDRAULIC PUMP UNIT
Connect hose from manual, air, or electric hydraulic pump to Rosin Press cylinder. Engage
hose fitting by pushing into mating cylinder and turning locking ring to secure.
STARTING THE ROSIN PRESS
Push power putton in. Button will illuminate in red color indicating power on condition.
Heat platens will take up to 15 minutes to heat and stabilize at desired temperature. When
starting the rosin press the temperature may overshoot programed temperature before
stabilizing.
STOPPING THE ROSIN PRESS
To turn o Rosin Press, push power button in, release, red light will stop, and power will be
in o mode.
DISCONNECT POWER CORDS
Unplug Rosin Press cord from power outlet. Unplug optional air or electric hydraulic power
unit from AC outlet.
COOL DOWN
Allow sucient time in power o mode for Rosin Press to cool before attempting to move
machine.
NOTICE: Be sure to hold the plug when disconnecting the power cord from the electrical
outlet. Do not disconnect by pulling on the power cord.
7
ROSIN PRESS OPERATION
8
Program optimal press platen temperature into temperaure control (PID) units. Typically
press operation will be between 195 to 220 degrees fahrenheit.
To adjust set value temperature on PID control push and hold up arrow button for three
seconds.
Wait at least 15 minutes after Rosin Press starts for press platens to reach desired and
stable temperature. Note that some slight fluctuation is normal.
Insert prefilled filter bag packet(s) and PTFE catchment paper between press platens. To
optimze press performance, position bags close to center of press platen surface. Multiple
small bags may be used.
Close press platens by activating hydraulic pump, either by hand unit or with power pump
options. Pressure gauge on pump will read approximately 500 psi. Wait until liquid can be
seen forming along packet edges, then slowly increase pump pressure to 7000 psi. Com-
bination of heat and intense prssure will push out all liquid rosin material from filter bag
packets.
Maximum recommended pressure as viewed on pump gauge is 7000 psi.. Approximately
20 Tons at press platens.
When all rosin has been extracted, release pump pressure. Platens will return to open posi-
tion. Remove spent filter bag packet and catchment paper, reload with fresh material, and
repeat press operation.
When filter bag packet and catchment paper have cooled suciently, dried rosin material
may be removed.
Increase temperature
Press and hold the up button for 3 seconds. At desired
temp, press the set button.
Decrease temperature
Hold the up arrow for 3 seconds. Then, press the down
arrow until the desired temp is shown. Press the set
button.
Check current temperature setting
Press the up button and the set temp will show. Press
the set button, and the current temp will show again.
PID TROUBLESHOOTING
Your press has a PID controller on it, it has a temperature sensor and two heating cartridg-
es per platen. These elements communicate with each other in a permanent closed loop
controlled by a microcomputer.
Your PIDs come preset with standard operational parameters however some users may
want to adjust or fine tune the PIDs further. For this reason we have included the following
guide for advanced troubleshooting.
PID Standard Operational Parameters
The below graphic shows the pre-set advanced settings menu and general setting menu on
the Rosin TRP Stack.
9
Indice
Altri manuali Triminator Utensili elettrici
