Trinamic TMCM-1141 Manuale utente

Getting started TMCM-1141

TRINAMIC Motion Control GmbH & Co. KG

Hamburg, Germany

www.trinamic.com

STARTING UP

1. Choose your interface.

USB: connect USB interface to PC.

Download and install the file TMCM-

1141.inf (www.trinamic.com) after

connecting the power supply.

RS485: use the interface connector and

connect an interface converter.

Connect the chosen interface to PC.

2. Connect the 24V DC power supply.

3. Connect motor to 4-pin connector of the

module

4. Turn power ON. The green LED starts

flashing slowly and the motor is

powered but in standstill now. If this

does not occur, turn power OFF and

check your connections and power

supply!

5. Start the TMCM-IDE program.

See next page how to configure the

connection and to use the IDE.

6. Type in the open window:

ROL 0, 500 //Rotate motor 0 with speed 500

WAIT TICKS, 0, 500

MST 0

ROR 0, 250 //Rotate motor 0 with speed 250

WAIT TICKS, 0, 500

MST 0

7. Click the Assemble icon. Thereafter click the Download icon to download the code to the module.

Click the Run icon. The program will now be executed.

8. Click the Stop icon and start TMCL™Direct Mode to issue the following commands:

ROR rotate right, motor 0, value 500 -> click Execute / The motor is rotating now.

MST motor stop, motor 0-> click Execute / The motor stops now.

FIRST STEPS ARE MADE.

Please refer to the TMCM-1141 Hardware and Firmware Manuals, too.

YOU NEED

-TMCM-1141

-Stepper motor

-Serial interface: RS485 or USB

-If you choose RS485: interface converter

suitable to your module

-Supply voltage +24 V DC (9… 28 V DC)

-TMCL-IDE program and PC

-Cables for interface, motor, and power

PRECAUTIONS

-Do not mix up connections or short-circuit pins.

-Avoid bounding I/O wires with motor power

wires.

-Do not exceed the maximum power supply of

+28 V DC!

-Do not connect or disconnect the motor while

powered!

-START WITH POWER SUPPLY OFF!

Motor

Power & RS485

In/Out

S/D

USB

Motor

Serial USB

interface

Converter

e.g. USB-2-485

Power supply

Pin 1 GND

Pin 2 9… 28V DC

RS485

Pin 3 GND

Pin 4 RS485+

Pin 5 RS485-

USB

RS485

Motor

Pin 1 OB2

Pin 2 OB1

Pin 3 OA2

Pin 4 OA1

Getting started TMCM-1141

TRINAMIC Motion Control GmbH & Co. KG

Hamburg, Germany

www.trinamic.com

TMCL-IDE

The TMCL-IDE is available on www.trinamic.com.

6. Click Assemble first, then Download and

Run to start the program.

Assemble

Download Run StopDissemble Continue

7. Stop all running programs by clicking

Stop and start Direct Mode by clicking the

appropriate icon.

8. The TMCM-1141 is automatically detected,

if the communication is established.

9. Issue a command by choosing Instruction,

Type, Motor, and Value and click Execute

to send it to the module.

1. Make sure the COM port you intend to

use is not blocked by another program.

2. Open TMCL-IDE by clicking TMCL.exe.

3. Choose Setup and Options and

thereafter the Connection tab.

4. Choose COM port and Type. Click OK.

5. Write a program code into the white

field and save it with File/Save.

Note, that TMCL programs run

standalone on the module, too.

TROUBLESHOOTING

IF COMMUNICATION IS NOT ESTABLISHED

-Check if the green LED lights up. If not, check

your power supply.

-Try to start Direct Mode and check, if the

module is detected automatically.

-Check, if you are using the right COM port and

it is not blocked by another program.

-Check, if the file TMCM-1141.inf is installed

correctly.

-Check your connection settings. Default: 9600

baud, address 1.

-Check if the RS485 converter functions.

IF MOTOR DOES NOT RESPOND

-Usually the communication is not established

(see above).

-Check the motor connection.

-If you are using a TMCL program try a

movement command in Direct Mode to check

if there is a problem with it.

-Restore factory settings by using instruction

137 for cancelling all settings modified by the

user.

Altri manuali per TMCM-1141

Altri manuali Trinamic Controllori

Trinamic

Trinamic TMCM-1140 Manuale utente

Trinamic

Trinamic PANdrive PD42-1-1370 Manuale utente

Trinamic

Trinamic TMCM-610 Manuale utente

Trinamic

Trinamic PD1-113-57-SE Manuale utente

Trinamic

Trinamic TMCM-310 Manuale utente

Trinamic

Trinamic TMCM-1210 Manuale utente

Trinamic

Trinamic TMCM-1141 Manuale utente

Trinamic

Trinamic TMCM-078 Manuale utente

Trinamic

Trinamic TMCM-3110 Manuale utente

Trinamic

Trinamic TMC428 Istruzioni per l'installazione e il funzionamento

Trinamic

Trinamic TMCM-6110 Manuale utente

Trinamic

Trinamic TMCM-343 Manuale utente

Trinamic

Trinamic TMCM-1181 Manuale utente

Trinamic

Trinamic SIXpack 2 Manuale utente

Trinamic

Trinamic TMCM-342 Manuale utente

Trinamic

Trinamic TMCM-110 Manuale utente

Trinamic

Trinamic TMCM-1260 Manuale utente

Trinamic

Trinamic TMCM-170-57 Manuale utente

Trinamic

Trinamic TMCM-1160 Manuale utente

Trinamic

Trinamic TMCM-1310 Manuale utente

Trinamic

Trinamic TMCM-013-42 Manuale utente

Trinamic

Trinamic TMCM-1311 Manuale per l'uso e la cura

Trinamic

Trinamic TMCM-6110 Manuale utente

Trinamic

Trinamic TMCL-LITE TMCM-1316 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente