Triple Plus DMX512 Manuale utente

3+DMX512 Controller Operation Manual

System features:

1.The controller has 8 output ports, each port can carry up to 170/512/768 pixels(Different pixels for different

chips).

2. The controller port output two kinds of signal protocol: ①DMX512/1990 international standard protocol and

DMX512 extended protocol; ②SPI/TTL serial protocol.

3. The controller output port provides three protections to ensure that the controller output port is not burn out in

the case of short circuit or reverse connection in the controlled lamp.

4. Controller ID automatic/manual numbering function, which can be numbered together with multiple controllers,

or individual controller numbers.

5. The controller comes with built-in effects to test on-load luminaires (all supported by RGB/RGBW luminaires).

6. The controller has DMX512 write function and address test. The single port or all ports carry the DMX512 IC

write address and perform address test on the luminaire.

7. The communication between the controllers adopts the international standard TCP/IP network protocol. The

optional transmission rate supports 100M/Gigabit adaptation, and the transmission speed is more stable and

fast. The maximum transmission distance between each two controllers can reach 100 meters. More than this

distance can increase the switch or use fiber for long-distance transmission.

8. The controller provides an LCD screen display that shows the model, ID, and operating status of the controller.

9. When connected with our online video software LedPlayer for computer control, the connection status of the

controller is monitored in real time on the computer. Using the online video software LedPlayer for computer

control can realize: program timing playback, program segment selection, effect brightness adjustment, white

balance online adjustment, program playback speed adjustment, display text, picture loop playback, etc., which

greatly satisfy the customer's application and Multiple needs in debugging.

10. The online video software LedPlayer comes with Gamma correction, which makes the color display more

delicate and vivid.

11. When the controller is connected to the computer, the IP address is set. The controller supports online and

offline integrated control. The online priority is the highest. When there is no online signal, it automatically

switches to the offline effect.

Note 1: The DMX/1903 IC on the controller can be controlled by MADRIX software. The maximum normal 3 unit (3

Univ) lamps per port, that is 3*170 pixels; multi-controllers combined into the largest control system

Compatible with 2048 units.

Note 2: The controller supports rack-mounting. If necessary, please contact the relevant business personnel before

placing an order.

Support chips：（Software select 3+DMX512）

Support chips

Max. support

light

Reamrks

International standard DMX512（like: UCS512, SM512, TM512,

GS512 etc）

4096 pixels

Suggest to carry 2400

pixels

UCS19**，ucs29**，ucs89**，ucs1603，ucs5603(UCS full series

TTL/SPI signal IC)

6144 pixels

Suggest to carry 4096

pixels

SM16703,09,12,SM16716,16726(SM full series TTL/SPI signal IC)

6144 pixels

——

TM18** series, TM19** series

6144 pixels

——

WS28**(WS full series TTL/SPI signal IC)

6144 pixels

——

GS8205,8206,8208

6144 pixels

——

P9813,9823,9883

6144 pixels

——

APA102

6144 pixels

——

SK6812

6144 pixels

——

MY9231

6144 pixels

——

GW6205

6144 pixels

——

INK1003

6144 pixels

——

LX1003,1103,1203 etc

6144 pixels

——

NOTE: More ICs are not listed one by one. For details, please refer to the on-board chip of the PCEdit software of the PC

software, or consult our sales and technical staff.

Product picture

3+DMX512 Reverse view

Indicator and button definition

1. Indicator

Power

Power indicator (always light after power on)

Status

Status indicator(Always on during normal operation /Strobe when writing)

2. Cascaded signal input and output port

Cascaded signal

NOTE

INPUT

Cascaded signal

input network port

The upper output is

connected to the

controller IN;

OUT is connected to the

next level controller

INPUT: Strobe with signal input

OUTPU

Cascaded signal

output network port

OUTPUT Strobe with signal output

3. Signal output port

OUT1--OU

Port definition

Signal type

Signal output

（TTL/SPI Signal）

GND(Negative）

DAT data

----

CLK clock

Signal output

（DMX512 signal）

GND(Negative）

A/DAT+

Signal

positive

B/DAT-

Signal

negative

ADDR

address

writing

4. Button function

SET

MODE

SPEED+

SPEED-

Play/Regular

mode

Numbering mode

Numbering start

button

Number up

Number down

Parameter

setting mode

Paramter

setting/enter

Item selection

Parameter

adjustment +

Parameter

adjustment -

MADRIX control

setting

Chip selection

Mode selection

Speed +

Speed -

Remarks

Normally boot into

normal mode, the

button has no effect

Press "SET" to

boot and enter

parameter

setting/function

setting

Press“+” to

bootand enter

MADRIX control

setting

Press “—” to boot

and enter

numbering mode

7. Power indicator

8. Status indicator

9. Cascade input

network port INPUT

10. Cascade output

network port OUTPUT

11. Output port

OUT1-OUT8

12. AC100-240V power

interface

5. Display definition:

Display

Definition

Playback

mode

ID: 001（number is 1）

PLAY >>> online/ master control

playback

STOP >>> Online/master control- pause

Regular

mode

ID: 001( number is 1)

A/C: Automatic/manual coding

T-800K controller model

Numbering

mode

ID：*** Starting number

Build-in

playback

effects

CHIP: chip 3：light channel

MOD: built-in effects SPD: Playback

speed

DMX512IC

Address

writing mode

The definition refer to 7.2 DMX512IC

Addressing Mode and Test

Lamp address

test mode

See 7.3 Lamp Address Test Mode for

definition in this book.

MADRIX

control

The definition refer to this book 8 MADRIX

control mode.

Wiring diagram

1 Computer online wiring diagram

2. Online and offline use wiring diagram

3. Controller signal output pirt wiring diagram

①.Regular laight wiring diagram ②.DMX512 differential signal wiring diagram

③. DMX512 single signal line wiring diagram ④. DMX512 differential signal wiring diagram

(AB wire to write address)

4. Controller--Online mode--Computer IP address setting

1. Turn on the computer --- network and sharing center;

2. Click to change the adapter settings;

3. ight click on Local Area Connection - Properties;

4. Click on "Internet Protocol Version 4 (TCP/IPV4)";

5. Change IP

IP：192.168.60.2

Subnet mask：255.255.255.0

6. Click OK to complete the IP address setting.

Note: This IP setting is applicable to regular online/Madrix software control.

Numbering function operate

Numbering has two methods:

1. Controller (master control operation) numbering function

The main control and sub-control (T-780K) are connected through the network cable (using the international

standard TCP/IP network protocol, and the network cable is 568B through).

1.1. The master control presses the “SPEED-/speed-” button to power on, and the “MODE” button adjusts the

arrow to “Set Slave ID” as shown in the figure:

1.2. Press the “SET”button again, the main control display enters the numbering page, the “SPEED+”

button and the “SPEED-”button adjust the number of the starting sub-control, as shown below:

1.3. After completing the number setting, press the “SET/Save”button to start the numbering.

1.4.The first step of the controller number is to automatically count the number of sub-controls. The display

"Write OK: 003" (take 3 sub-control numbers as an example)

1.5. The number is completed, the main control display: As shown in the figure "Write Num: 003", 3 controllers

are programmed.

“ Last ID: 003” means the last controller number is 3

Sub-control 3+DMX512 display as below:

First set ID：0001 Second set ID：0002 Third set ID：0003

1.6. Check the controller number. If you need to renumber, press and hold the “SPEED-”button

to restart the numbering. If you do not need to renumber, press any button—the master

restarts and returns to the playback mode.

Note 1: When the controller is numbered, the level network port must be connected in strict accordance with

the controller silkscreen prompt (IN/OUT); the maximum sub-control number is 203.

2. Controller numbering

The 3+DMX512 use network cable connect (using the international standard TCP/IP network protocol, the

network cable is 568B straight)

2.1. The first 3+DMX512 controller, press and hold the “SPEED-”button, the controller will be powered on

and enter the manual coding mode. The display shows: “ID: 0001”as shown in the figure, ie the current

number of the controller is No. 1, press the “SPEED+”and “SPEED-”keys adjust the starting number.

Button silk screen

SET

SPEED+

SPEED-

Button function

Numbering start button

Digital plus

Digital subtraction

NOTE

Numbering mode, "MODE"

button is not available

Press "-" to power on, enter the

numbering mode

2.2. After completing the start number adjustment, press the “SET”button to start the

number start number and display: “Writing...”

2.3. During the numbering process, the controller detects the number of connected

controllers (the number of connected controllers). As shown in Figure 003, a total of

three controllers are detected.

2.4. The number is completed, the first controller displays: as shown in the figure "Write

Num:003": 3 controllelers are searched

" Last ID: 003" The last one is numbered 3

Other controller display, as show in the figure:

“ID:0002 A” ；ID:0002 means the controller number is No. 2 A: Indicates that the number is

automatically generated

The second set: A-0002 The third set: A-0003

2.5.Check whether each controller number is correct or needs to be renumbered. Then the first

controller long time presses the “SPEED-” button to return to the manual numbering; the end

numbering can be exited by pressing the button (any button is ok). The first controller

restarts “Restart...” and returns to normal play mode.

Note: When the controller is numbered, the cascaded networking ports must be connected in strict accordance

with the controller silkscreen prompt (INPUT/OUTPUT).

3+DMX512 Parameter setting and function operation

Press the “SET”button, and the controller will start up and enter the parameter

setting and other function interfaces.

①. PLAY Built-in effect playback mode

②. WRITE ADDRESS Address writing mode

③.TEST DMX ADDR Lamps address testing mode

④. RGB,RGBW Lamps channel selection mode

⑤. 100-BASE Transmission rate selection mode

1. Built-in effects mode (support RGB/RGBW these two

kinds channel lamps)

1.1. Press the “SET”button, and the controller will start up, enter the parameter setting and

other function interfaces, as shown in the figure:

1.2. Press the “MODE”button to move the arrow to select “PLAY”, then press the “SET”

button to enter the built-in effect playback mode interface.

As shown in the figure:

①.CHIP chip model（refer to the IC model list）

②.3 Channel selection（3/4）

③.MOD Built-in effects（refer to the built-in effects list）

④. SPD Playback speed（refer to the speed level corresponding frame list）

Note: When the built-in effect is played, the supported lamp channel is set by the “Lamp

Channel Selection Mode”.

1.3. Button function list

Button silk screen

SET

MODE

SPEED+

SPEED-

Function

Chip selection

Mode selection

Speed up

Speed down

NOTE

Press “SET” to power on, and enter the built-in effects mode

1.4. Press “SET”to switch the IC model

IC model list

DMX (standard 250Kbps)

TM1803

UCS1903

GS8205

SM16703

DMX 500K

WS2811

1.5. Press “MODE”to switch the built-in effects

Built-in effects list

Colorful jump

Colorful change

Colorful gradient

White light gradient

1.6. Press “SPEED+”and “SPEED- ”to switch the speed;

Speed lever corresponding frame rate list

Speed

Frame

rate/second

Speed

Frame

rate/second

Speed

Frame

rate/second

Spee

Frame

rate/second

4 frame

8 frame

14 frame

23 frame

5 frame

9 frame

16 frame

25 frame

6 frame

10 frame

18 frame

27 frame

7 frame

12 frame

20 frame

30 frame

1.7. After completing the built-in effect playback, shut down and restart to return to normal mode.

-255）

③.IC : Chip model

（Rfer to DMX512 IC list）

④. PORT NUM: Address port

3+DMX512 Controller ---MADRIX SETTING

Press “SET”, and power on the controlller at the same time, enter MADRIX setting interface, as shown

below:

○

1SET MADRIX Turn on/off MADRIX software

○

2SET Univ Set support lights quantity

○

3 SET IC support IC selection

Note: The parameters need to be set and set in order of 1, 2, 3, and the controller will be

restarted after completion.

1.1. Turn on/off MADRIX function

1. Press “SET”, and turn on the controller at the same time, enter the MADRIX setting

parameter interface.

2. Press the “MODE”button to move the arrow to select “SET MADRIX”to enable/disable

the MADRIX function, as shown below.

3. Press “SET”to confirm entry, open/close Mai Jue; as shown below;

1. Open MADRIX function

2. Close MADRIX function

4. Press the “SPEED+” and “SPEED-” buttons to move the arrow up and down to select the

On/Off option.

5. Press the “MODE”button to confirm the selection and display the following picture:

6. Select to complete the selection, press the “SET”button to exit, and return to the MADRIX

setting interface.

1.2. Set the number of lamps on board

1. Press the “SET”button, and the controller will start up and enter the Mai Jue set parameter

interface.

2. Press the “MODE”button to move the arrow and select “SET Univ”to set the number of

lamps on the load, as shown below.

Indice

Altri manuali Triple Plus Controllori

Triple Plus

Triple Plus CLM-IRAMAP-1-02 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente