Tripp Lite B140-002-DD Manuale utente

Owner’s Manual

DVI Over Cat5 Dual Display

Extender / Splitter

Model: B140-002-DD

1111 W. 35th Street, Chicago, IL. 60629 • www.tripplite.com/support

Package Contents 2

Product Features 2

Mounting 3

Standard Installation 4

Remote Repeater Installation 6

Troubleshooting 8

Warranty & Warranty Registration 11

WARRANTY

REGISTRATION

chance to win a FREE Tripp Lite

product www.tripplite.com/warranty

13-01-085-933287_revA.indd 1 1/30/2013 3:44:15 PM

Package Contents

Product Features

• B140-002-DD Extender / Splitter Transmitter Unit

• External Power Supply (Input: 100-240V, 50/60Hz, 0.5A Output: 5V, 2A)

• Mounting Hardware

• Owner’s Manual

• Transmits a DVI-D Single-Link signal from a set of Dual DVI inputs to two

sets of Dual Displays

• A B140-Series remote receiver is needed at each monitor

• For longer distances: Use a B140-1A0 or B140-1A0-WP active receiver to

extend a 1920 x 1080 @ 60Hz signal up to 150 ft. from the transmitter

(or a 1024 x 768 @ 60Hz signal up to 200 ft. from the transmitter)

• For shorter distances: Use a B140-1P0 or B140-1P0-WP passive receiver

to extend a 1920 x 1080 @ 60Hz signal up to 50 ft. from the transmitter

(or a 1024 x 768 @ 60Hz signal up to 100 ft. from the transmitter)

• Use 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series,

to achieve maximum distance and resolution

• Further expand the range and number of monitors by adding B140-110

remote repeater units

• Add up to three repeaters on each of the B140-002-DD channels, for a

total of 4 displays per channel (An active receiver should be the last unit in

a channel)

• A 1920 x 1080 @ 60Hz signal can be extended up to 125 ft. for each repeater

added into a channel (or up to 175 ft. for a 1024 x 768 @ 60Hz signal)

• DVI 1.0 compliant

• HDCP compatible

• Mounting hardware included that allows the unit to be wall-mounted,

rackmounted, or pole mounted

• Plug and play; no software or drivers required

• Compatible with all operating systems

• Compliant with the Federal Trade Agreements Act (TAA) for GSA Schedule

purchases

13-01-085-933287_revA.indd 2 1/30/2013 3:44:15 PM

Product Features

Optional Accessories:

• B140-1A0 DVI Over Cat5 Extender – Active Remote Receiver Unit

• B140-1A0-WP DVI Over Cat5 Extender – Active Remote Receiver Wallplate

• B140-1P0 DVI Over Cat5 Extender – Passive Remote Receiver Unit

• B140-1P0-WP DVI Over Cat5 Extender – Passive Remote Receiver Wallplate

• B140-110 DVI Over Cat5 Extender – Remote Repeater Unit

• N202-Series Cat6 24AWG, Solid Wire Patch Cables

• P561-Series DVI-D Single-Link Cables

• P566-Series DVI to HDMI Adapter Cables*

* When converting DVI to HDMI, only a video signal will be transmitted. DVI does not support audio.

Mounting

The B140-002-DD comes with mounting hardware that allows it to be

mounted in a variety of ways. The following images show the different ways the

included mounting brackets can be attached for different mounting methods.

Note: The images below show a B140-1A0, but the mounting hardware installation is the same

for the B140-002-DD.

Wallmount 1 Wallmount 2

19” Rackmount Pole Mount

13-01-085-933287_revA.indd 3 1/30/2013 3:44:17 PM

Standard Installation

Note:

1. Test to make sure that the entire installation works properly before pulling cables through

ceilings/walls.

2. 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve

maximum distance and resolution.

3. The signal from input port A is transmitted to RJ45 output ports 1A and 2A. The signal from

input port B is transmitted to RJ45 output ports 1B and 2B. For your Dual Display installation

to appear correctly in extended screen mode, locate the monitor connected to RJ45 port 1A

next to the monitor connected to RJ45 port 1B. Likewise, locate the monitor connected to

RJ45 port 2A next to the monitor connected to RJ45 port 2B.

B140-002-DD B140-1P0 B140-1P0-WP

B140-1A0-WP

B140-1A0

DVIOVER Cat5

EXTENDER

REMOTEUNIT

MODEL:B140-1P0

Up to 100 ft. at 1920 x 1080 @ 60Hz

Up to 50 ft. at 1024 x 768 @ 60Hz

Up to 150 ft. at 1920 x 1080 @ 60Hz

Up to 200 ft. at 1024 x 768 @ 60Hz

1Make sure power to the DVI source is turned off.

2Connect the ﬁrst DVI port from the source to DVI input port A.

3Connect the second DVI port from the source to DVI input port B.

4Connect the external power supply to the B140-002-DD and plug it

into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or

Uninterruptible Power Supply (UPS). When receiving power, the Green

RJ45 LEDs on the B140-002-DD will illuminate.

13-01-085-933287_revA.indd 4 1/30/2013 3:44:18 PM

Standard Installation

5Using Cat5e/6 cable, connect RJ45 port 1A to a B140-Series remote

receiver unit.

6Repeat step 5 to connect each RJ45 port to a B140-Series remote

receiver unit.

7B140-1A0 and B140-1A0-WP only: Connect the external power supply

to the active receiver unit, and plug it into a Tripp Lite Surge Suppressor,

PDU, or UPS. When receiving power, the Green RJ45 LED on the

B140-1A0, and the Green Power LED on the B140-1A0-WP, will illuminate.

8Repeat step 7 for each active receiver unit in the installation.

9Connect a receiver unit to a monitor using a Tripp Lite P561-Series

DVI-D Single-Link cable. If you have a B140-1P0, connect its built-in DVI

connector to a monitor. When connected to and receiving power from a

monitor, the Green RJ45 LED on the B140-1P0, and the Green Power LED

on the B140-1P0-WP, will illuminate.

Note: See note number 3 at the beginning of the Standard Installation section, and

reference the installation diagram, to ensure that the correct video signals are transmitted to

the monitors in your Dual Display installations.

Repeat step 9 to connect each receiver unit to a monitor.

Turn on the power to the DVI source. The Orange RJ45 LEDs on the

B140-002-DD and B140-1A0, and the Orange Activity LED on the

B140-1A0-WP, will illuminate. The video image should now be displayed

on the connected monitors.

B140-1A0 and B140-1A0-WP only: If necessary, use the Equalization

control to adjust the video image.

Note: An improper Equalization setting can cause the monitor not to display an image at all.

Try each setting until an acceptable image is displayed.

13-01-085-933287_revA.indd 5 1/30/2013 3:44:18 PM

Remote Repeater Installation

Note:

1. Test to make sure that the entire installation works properly before pulling cables through

ceilings/walls.

2. 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve

maximum distance and resolution.

3. The signal from input port A is transmitted to RJ45 output ports 1A and 2A. The signal from

input port B is transmitted to RJ45 output ports 1B and 2B. For your Dual Display installation

to appear correctly in extended screen mode, locate the monitor connected to RJ45 port 1A

next to the monitor connected to RJ45 port 1B. Likewise, locate the monitor connected to

RJ45 port 2A next to the monitor connected to RJ45 port 2B.

B140-110B140-110

B140-002-DD

B140-110

B140-1A0

B140-1A0-WP

Up to 175 ft. at 1024 x 768 @ 60Hz

Up to 125 ft. at 1920 x 1080 @ 60Hz

Up to 175 ft. at 1024 x 768 @ 60Hz

Up to 125 ft. at 1920 x 1080 @ 60Hz

B140-110B140-110

B140-110

1Make sure power to the DVI source is turned off.

2Connect the ﬁrst DVI port from the source to DVI input port A.

3Connect the second DVI port from the source to DVI input port B.

4Connect the external power supply to the B140-002-DD and plug it

into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or

Uninterruptible Power Supply (UPS). When receiving power, the Green

RJ45 LEDs on the B140-002-DD will illuminate.

5Using Cat5e/6 cable, connect RJ45 port 1A to the RJ45 input port of a

B140-110 remote repeater unit.

6Connect a monitor to the DVI output port on the repeater using a Tripp Lite

P561-Series DVI-D Single-Link cable.

13-01-085-933287_revA.indd 6 1/30/2013 3:44:20 PM

Remote Repeater Installation

7Connect the external power supply to the repeater and plug it into a

Tripp Lite Surge Suppressor, PDU, or UPS. The Green Power LED and the

Green RJ45 LEDs illuminate to indicate the unit is receiving power.

Add up to 3 repeaters per channel, for a total of 4 displays (an active remote

receiver should be the last unit in a channel). To connect additional repeaters,

proceed to step 8. To ﬁnish your installation with a B140-1A0 or

B140-1A0-WP receiver, proceed to step 11.

8Using Cat5e/6 cable, connect the RJ45 output port on the ﬁrst repeater to

the RJ45 input port on a second repeater.

9Connect a monitor to the DVI output port on the repeater using a Tripp Lite

P561-Series DVI-D Single-Link cable.

Connect the external power supply to the repeater and plug it into a

Tripp Lite Surge Suppressor, PDU, or UPS. The Green Power LED and the

Green RJ45 LEDs illuminate to indicate the unit is receiving power.

To add a third repeater, repeat steps 8 through 10. To ﬁnish your installation

with a B140-1A0 or B140-1A0-WP receiver, proceed to step 11.

Using Cat5e/6 cable, connect the RJ45 output port on the last repeater to

the RJ45 input port on a B140-1A0 or B140-1A0-WP receiver.

Connect a monitor to the DVI output port on the receiver using a

Tripp Lite P561-Series DVI-D Single-Link cable.

Connect the external power supply to the active receiver unit, and plug it

into a Tripp Lite Surge Suppressor, PDU, or UPS. When receiving power,

the Green RJ45 LED on the B140-1A0, and the Green Power LED on the

B140-1A0-WP, will illuminate.

Repeat steps 5 through 13 for each RJ45 output port on the B140-002-DD.

Note: See Note number 3 at the beginning of the Remote Repeater Installation section, and

reference the installation diagram to ensure the correct video signals are transmitted to the

monitors in your dual display installation.

13-01-085-933287_revA.indd 7 1/30/2013 3:44:20 PM

Remote Repeater Installation

Turn on the power to the DVI source. The Orange RJ45 LED’s on the

B140-002-DD, B140-110, and B140-1A0, and the Orange Activity LED

on the B140-1A0-WP, will illuminate. The video image should now be

displayed on the connected monitors.

If necessary, use the Equalization control on the B140-110, B140-1A0,

and/or B140-1A0-WP to adjust the video image.

Note: An improper Equalization setting can cause the monitor not to display an image at all.

Try each setting until an acceptable image is displayed.

Troubleshooting

If you are unable to get an acceptable image after following the installation

instructions, try the troubleshooting tips below.

1Is the external power supply that came with the product connected and

plugged into a working power source? For the product to function properly,

it must be connected to and receiving power from the external power

supply.

2Was the power to the DVI source turned off prior to installation? If not,

restart your computer.

3Have you adjusted the Equalization setting on the repeater and/or receiver

units? There are built-in Equalization adjustment knobs on every repeater

and active receiver, which can be adjusted to obtain the best picture

quality. Use the mini screwdriver included with the product to adjust this

setting until an acceptable image is displayed.

Note: An improper Equalization setting can cause the monitor not to display an image at all.

Try each setting until an acceptable image is displayed.

13-01-085-933287_revA.indd 8 1/30/2013 3:44:20 PM

Troubleshooting

4What resolution are you trying to reach? Tripp Lite’s DVI over Cat5

extenders are tested to support up to 1920 x 1080 @ 60Hz video

resolution (See the Product Features section or the installation diagrams

in this manual for details on max distance and resolution when using the

repeater and the different receivers). The shorter the extension distance,

the higher the resolution you will be able to obtain. If you are not able

to get an acceptable image after adjusting the Equalization setting, try

lowering your computer’s video resolution and/or adjusting the refresh rate.

5What type of cabling are you using? Inferior cabling can result in poor

performance, so it is important that you use cables that can support the

video resolution you are trying to obtain. To achieve maximum distance

and resolution, 24AWG solid wire UTP cable must be used. Tripp Lite’s

N202-Series Cat6 cables are made with 24AWG solid wire, as are the

N022-01K-GY (Cat5) and N222-01K-GY bulk cables. Also, the DVI

cables you are using must support the resolution you are trying to obtain.

Inexpensive, low quality DVI cables may not support the maximum

resolution. It is recommended that you use Tripp Lite’s P561-Series DVI-D

Single-Link cables, as they have been tested to work with the B140-Series

extender products.

6Test your cables to ensure they are working properly. For example, connect

your DVI cables between a source and monitor that you know works to

see if the cable is functioning. For Cat5e/6 cable, connect it between a

computer and a network to verify that it establishes a network connection.

7Do you have any patch panels or other devices in between the transmitter,

repeater, and receiver units? Tripp Lite’s DVI over Cat5 extender products

were designed to be connected directly from the transmitter to the

repeater and/or receiver via UTP cable. The more connection points that

are in between the source and the remote monitor, the more likely it will

be that signal degradation will occur, causing poor performance. If you

have a patch panel or other device in between, it should be removed from

the installation.

13-01-085-933287_revA.indd 9 1/30/2013 3:44:20 PM

Troubleshooting

8Check your cabling for any damages that may have occurred during

installation. If a cable connector is loosened from pulling through ceilings/

walls, or the cable jacket is damaged causing the wiring to be exposed,

you will not be able to achieve maximum performance.

9Are the transmitter, repeater, and/or receiver located in an area that

exposes them to higher temperatures? If the product is overheated, it will

not function properly.

Are you using a VGA to DVI adapter with this product? The B140-Series

extenders support DVI-D (Digital) only, and will not function if connected to

a VGA computer or monitor.

If using a DVI to HDMI adapter with this product, you will only be able to

transmit a video signal. DVI does not support audio, and will not be able

to send an audio signal to an HDMI display.

The signal from input port A is transmitted to RJ45 output ports 1A and

2A. The signal from input port B is transmitted to RJ45 output ports 1B

and 2B. For your Dual Display installation to appear correctly in extended

screen mode, locate the monitor connected to RJ45 port 1A next to

the monitor connected to RJ45 port 1B. Likewise, locate the monitor

connected to RJ45 port 2A next to the monitor connected to RJ45 port

2B. Reference the installation diagrams in this manual for examples of a

correct setup.

If you have followed the proper installation procedures, and all monitors

continue to display the same image, you may have to go into your

computer’s Display Settings menu and activate Extended monitor mode.

If your computer is set to Mirror (or Duplicate) monitor mode, the same

image will be displayed on both screens.

13-01-085-933287_revA.indd 10 1/30/2013 3:44:20 PM

Indice

Altri manuali Tripp Lite Estensione

Tripp Lite

Tripp Lite B126-1A1-WHD4HH Manuale utente

Tripp Lite

Tripp Lite B127U-002-PDPH2 Manuale utente

Tripp Lite

Tripp Lite P130-000-AUDIO2 Manuale utente

Tripp Lite

Tripp Lite HDMI B122-000-60 Manuale utente

Tripp Lite

Tripp Lite B126-1A1-IR Manuale utente

Tripp Lite

Tripp Lite B132-100 Manuale utente

Tripp Lite

Tripp Lite HDMI B122-000-60 Manuale utente

Tripp Lite

Tripp Lite B150-1A1-HDMI Manuale utente

Tripp Lite

Tripp Lite B136-100 Manuale utente

Tripp Lite

Tripp Lite B130-101A-MR Manuale utente

Tripp Lite

Tripp Lite B127U-111-PDPD Manuale utente

Tripp Lite

Tripp Lite B203-101-IND Manuale utente

Tripp Lite

Tripp Lite B013-000 Manuale utente

Tripp Lite

Tripp Lite B127A-1A1-BHBH Manuale utente

Tripp Lite

Tripp Lite B164-101-WIR Manuale utente

Tripp Lite

Tripp Lite B126-1A1-POC Manuale utente

Tripp Lite

Tripp Lite B123-001-60 Manuale utente

Tripp Lite

Tripp Lite B136-004 Manuale utente

Tripp Lite

Tripp Lite B136-101-WP-1 Manuale utente

Tripp Lite

Tripp Lite NPOE-EXT-1G30WP Manuale utente

Tripp Lite

Tripp Lite B203-101-IND-ER Manuale utente

Tripp Lite

Tripp Lite B126-1A1-WP Manuale utente

Tripp Lite

Tripp Lite 0DT23008 Manuale utente

Tripp Lite

Tripp Lite B203-101-PNP Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente