Tripp Lite B126-2X2 Manuale utente

Owner’s Manual

HDMI Over Cat5

Matrix Switch

Models: B126-2X2, B126-4X4

1111 W. 35th Street, Chicago, IL. 60609 • www.tripplite.com/support

Package Contents 2

Product Features 2

Mounting 4

Standard Installation 5

Remote Repeater Installation 7

RS232 Serial Control 10

Troubleshooting 13

Warranty & Warranty Registration 15

WARRANTY

REGISTRATION

chance to win a FREE Tripp Lite

product www.tripplite.com/warranty

13-11-140 93-32BB.indd 1 11/19/2013 4:57:38 PM

Package Contents

Product Features

• B126-2X2orB126-4X4LocalTransmitterUnit

• ExternalPowerSupply

(Input:100-240V,50/60Hz,0.5AOutputB126-2X2:5V,2A;

OutputB126-4X4:5V,3A)

• 3.5mmtoDB9AdapterCable

• MountingHardware

• RemoteControl

• Owner’sManual

• SharemultipleHDMIsourcesbetweenmultiplemonitors

• Allowsanyinputtoberoutedtoanyoutput;orthesameinputtobe

routed to multiple outputs

• TransmitsthesignaloveroneCat5e/6cabletoaremotemonitorupto

175ft.away

• AB126-Seriesremotereceiverisneededateachmonitor

• Forlongerdistances:UseaB126-1A0orB126-1A0-WP-1active

remotereceivertoextenda1080p@60Hzsignalupto125ft.from

thetransmitter(ora1080i@60Hzsignalupto175ft.fromthe

transmitter)

• Forshorterdistances:UseaB126-1P0orB126-1P0-WP-1passive

remotereceivertoextenda1080p@60Hzsignalupto50ft.from

thetransmitter(ora1080i@60Hzsignalupto75ft.fromthe

transmitter)

• Use24AWG,SolidWireCat5e/6cable,suchasTrippLite’s

N202-Series,toachievemaximumdistanceandresolution

• Furtherexpandtherangeandnumberofmonitorsbyadding

B126-110remoterepeaterunits

13-11-140 93-32BB.indd 2 11/19/2013 4:57:38 PM

Product Features

• Adduptothreerepeatersoneachchannelofthematrixswitch,fora

totalof4displaysperchannel(Anactiveremotereceivershouldbethe

lastunitinachannel)

• A1080p@60Hzsignalcanbeextendedupto125ft.foreach

repeateraddedintoachannel(orupto175ft.fora1080i@

60Hzsignal)

• Switchbetweeninputsviapushbuttons,remotecontrol,

orRS232serial

• HDCP-compatible

• Mountinghardwareincluded

• Plug-and-play;nosoftwareordriversrequired

• Compatiblewithalloperatingsystems

• CompliantwiththeFederalTradeAgreementsAct(TAA)forGSA

Schedulepurchases

Optional Accessories:

• B126-1A0orB126-1A0-WP-1–ActiveRemoteReceiverUnits

• B126-1P0orB126-1P0-WP-1–PassiveRemoteReceiverUnits

• B126-110HDMIOverCat5Extender–RemoteRepeaterUnit

• N202-SeriesCat624AWG,SolidWirePatchCables

• P568-SeriesHigh-SpeedHDMICables

• P520-006RS-232SerialExtensionCable

13-11-140 93-32BB.indd 3 11/19/2013 4:57:38 PM

Mounting

TheB126-2X2andB126-4X4comewithmountinghardwarethatallows

themtobemountedinavarietyofways.Thefollowingimagesshow

thedifferentwaystheincludedmountingbracketscanbeattachedfor

different mounting methods.

Note: The images below show a B126-1A1 HDMI over Cat5 Receiver Unit, but the mounting

hardware installation is the same for the B126-2X2 and B126-4X4.

Wallmount 1 Wallmount 2

19” Rackmount Pole Mount

13-11-140 93-32BB.indd 4 11/19/2013 4:57:39 PM

Standard Installation

Note:

1. Test to make sure that the entire installation works properly before pulling cables through

ceilings/walls.

2. 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve

maximum distance and resolution.

3. The diagram below shows a B126-2X2 installation, but installation will be the same for the

B126-4X4, except for the number of ports.

4. The back panel of the B126-4X4 contains an IR port which has been capped off. This port is

intended for future use, and does not currently function.

B126-2x2

Computer

Blu-Ray™

Cable Box

or DVR

B126-1P0

B126-1A0

Up to 125 ft. at 1080p @ 60Hz

Up to 175 ft. at 1080i @ 60Hz

Up to 50 ft. at 1080p @ 60Hz

Up to 75 ft. at 1080i @ 60Hz

1 Makesurealldevicesbeingconnectedareturnedoff.

2Optional:Connectthe3.5mmtoDB9adaptertotheRS232serial

portontheswitch,andthentotheDB9serialportonthecomputer

youwillbeusingtocontrolitwith.

3 ConnecttherstHDMIsourcetotheportontheswitchmarkedSource A.

4 Repeatstep3toconnectadditionalHDMIsourcestotheremainingports.

5 Connecttheexternalpowersupplytotheswitchandplugitintoa

TrippLiteSurgeSuppressor,PowerDistributionUnit(PDU),or

UninterruptiblePowerSupply(UPS).Whenreceivingpower,thefollowing

LEDswillilluminate:TheGreenPowerLED,TheOrangeSourceLEDs

(for the Sourceportsthathavedevicesconnectedtothem),andthe

GreenRJ45Output LEDs.AGreenLEDwillalsoilluminatetoindicate

thesourcethatisbeingtransmittedtoeachOutput port.

6 UsingCat5e/6cable,connecttheRJ45portmarkedOutput 1 to a

B126-Seriesremotereceiverunit.

13-11-140 93-32BB.indd 5 11/19/2013 4:57:40 PM

Standard Installation

7 Repeatstep6toconnectadditionalB126-Seriesremotereceiver

units to the remaining ports.

8B126-1A0 and B126-1A0-WP-1 only:Connecttheexternalpower

supplytotheactiveremotereceiverunit,andplugitintoaTrippLite

SurgeSuppressor,PDUorUPS.Whenreceivingpower,theGreen

RJ45LEDontheB126-1A0,andtheGreenPowerLEDonthe

B126-1A0-WP-1,willilluminate.

9 Repeatstep8foreachadditionalactiveremotereceiverunitinthe

installation.

 ConnecttheremotereceiverunittoamonitorusingaTrippLiteP568-

SeriesHigh-SpeedHDMIcable.IfyouhaveaB126-1P0,connectits

built-inHDMIconnectortoamonitor.Whenconnectedtoand

receivingpowerfromamonitor,theGreenRJ45LEDontheB126-1P0,

andtheGreen PowerLEDontheB126-1P0-WP-1,willilluminate.

Repeat step 10 for each additional remote receiver unit in the

installation.

 Turnonthepowertotheconnecteddevices.TheOrangeRJ45LEDs

ontheB126-2X2,B126-4X4andB126-1A0,andtheOrangeActivity

LEDontheB126-1A0-WP-1,willilluminate.Thevideoimageshould

nowbedisplayedontheconnectedmonitors.

 B126-1A0andB126-1A0-WP-1only:Ifnecessary,usethe

Equalization control to adjust the video image.

Note: An improper Equalizationsetting can cause the monitor not to display an image at all.

Try each setting until an acceptable image is displayed.

 Presstheswitchnexttoeachsetof Output LEDstoswitchthesource

beingdisplayedonthecorrespondingOutput monitor. You can also

usetheincludedremotecontroltoswitchbetweensources.Aswith

theswitchnexttotheOutputLEDs,pressthebuttonontheremote

control of the desired Outputporttoswitchthesourcebeingdisplayed.

Note: The same 4 button remote control comes with both the B126-2X2 and B126-4X4.

Buttons 3 and 4 will not be used for the B126-2X2.

SeetheRS232 Serial Control section in this manual for details on

controllingtheswitchusingTerminalEmulationSoftware.

13-11-140 93-32BB.indd 6 11/19/2013 4:57:41 PM

Remote Repeater Installation

Note:

1. Test to make sure that the entire installation works properly before pulling cables through

ceilings/walls.

2. 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve

maximum distance and resolution.

3. The diagram below shows a B126-2X2 installation, but installation will be the same for the

B126-4X4, except for the number of ports.

4. The back panel of the B126-4X4 contains an IR port which has been capped off. This port is

intended for future use, and does not currently function.

B126-2x2

B126-110 B126-110 B126-110

Up to 175 ft. at 1080i @ 60Hz

Up to 125 ft. at 1080p @ 60Hz

B126-1A0-WP-1

B126-110 B126-110 B126-110

Up to 175 ft. at 1080i @ 60Hz

Up to 125 ft. at 1080p @ 60Hz

Blu-Ray™

Cable Box

or DVR

B126-1A0

Computer

1 Makesurealldevicesbeingconnectedareturnedoff.

2Optional: Connectthe3.5mmtoDB9adaptertotheRS232serial

portontheswitch,andthentotheDB9serialportonthecomputer

youwillbeusingtocontrolitwith.

3 ConnecttherstHDMIsourcetotheportontheswitchmarked

Source A.

4 Repeatstep3toconnectadditionalHDMIsourcestotheremaining

ports.

13-11-140 93-32BB.indd 7 11/19/2013 4:57:42 PM

Remote Repeater Installation

5 Connecttheexternalpowersupplytotheswitchandplugitintoa

TrippLiteSurgeSuppressor,PDU,orUPS.Whenreceivingpower,

thefollowingLEDswillilluminate:TheGreenPowerLED,theOrange

Source LEDs(fortheSource ports that have devices connected

tothem),andtheGreenRJ45 OutputLEDs.AGreenLEDwillalso

illuminatetoindicatethesourcethatisbeingtransmittedtoeach

Output port.

6 UsingCat5e/6cable,connecttheRJ45portmarked Output 1 to the

RJ45inputportofaB126-110remoterepeaterunit.

7 ConnectamonitortotheHDMIoutputportontherepeaterusinga

TrippLiteP568-SeriesHigh-SpeedHDMIcable.

8 Connecttheexternalpowersupplytotherepeaterandplugitinto

aTrippLiteSurgeSuppressor,PDUorUPS.TheGreenPowerLED

andtheGreenRJ45LEDsilluminatetoindicatetheunitisreceiving

power.

Adduptothreerepeatersperchannel,foratotalof4displays(an

active remote receiver should be the last unit in a channel). To connect

additionalrepeaters,proceedtostep9.Tonishyourinstallationwitha

B126-1A0orB126-1A0-WP-1receiver,proceedtostep12.

9 UsingCat5e/6cable,connecttheRJ45outputportontherst

repeatertotheRJ45inputportonasecondrepeater.

 ConnectamonitortotheHDMIoutputportontherepeaterusinga

TrippLiteP568-SeriesHigh-SpeedHDMIcable.

 Connecttheexternalpowersupplytotherepeaterandplugitinto

aTrippLiteSurgeSuppressor,PDUorUPS.TheGreenPowerLED

andtheGreenRJ45LEDsilluminatetoindicatetheunitisreceiving

power.

Toaddathirdrepeater,repeatsteps9through11.Tonishyour

installationwithaB126-1A0orB126-1A0-WP-1receiver,proceedto

step 12.

13-11-140 93-32BB.indd 8 11/19/2013 4:57:42 PM

Remote Repeater Installation

 UsingCat5e/6cable,connecttheRJ45outputportonthelast

repeatertotheRJ45inputportonaB126-1A0orB126-1A0-WP-1

receiver.

 ConnectamonitortotheHDMIoutputportonthereceiverusinga

TrippLiteP568-SeriesHigh-SpeedHDMIcable.

 Connecttheexternalpowersupplytotheactiveremotereceiverunit,

andplugitintoaTrippLiteSurgeSuppressor,PDU,orUPS.When

receivingpower,theGreenRJ45LEDontheB126-1A0,andthe

GreenPower LEDontheB126-1A0-WP-1,willilluminate.

Repeatsteps6through14fortheremainingOutput ports on the switch.

 Turnonpowertotheconnecteddevices.TheOrangeRJ45LEDs

ontheB126-2X2,B126-4X4,B126-110,andB126-1A0,andthe

OrangeActivityLEDontheB126-1A0-WP-1,willilluminate.Thevideo

imageshouldnowbedisplayedontheconnectedmonitors.

 Ifnecessary,usetheEqualization control on the repeater and receiver

units to adjust the video image.

Note: An improper Equalization setting can cause the monitor not to display an image at all.

Try each setting until an acceptable image is displayed.

 PresstheswitchnexttoeachsetofOutputLEDstoswitchthe

sourcebeingdisplayedonthecorrespondingOutput monitor. You

canalsousetheincludedremotecontroltoswitchbetweensources.

AswiththeswitchnexttotheOutputLEDs,pressthebuttononthe

remote control of the desired Outputporttoswitchthesourcebeing

displayed.

Note: The same 4 button remote control comes with both the B126-2X2 and B126-4X4.

Buttons 3 and 4 will not be used for the B126-2X2.

 SeetheRS232 Serial Control section in this manual for details on

controllingtheswitchusingTerminalEmulationSoftware.

13-11-140 93-32BB.indd 9 11/19/2013 4:57:42 PM

RS232 Serial Control

BeforeusingRS232SerialControl,youmustrstgointoyouTerminal

EmulationSoftwareandupdatetheCOMportsettings.

1 GototheSetupdrop-downmenuandselecttheSerial Port option.

2 SelecttheCOMportthatisbeingused,andupdatetheremaining

settingsasfollows:BaudRate(57600),Data(8bit),Parity(none),

Stop(1bit),FlowControl(none).

13-11-140 93-32BB.indd 10 11/19/2013 4:57:42 PM

Altri manuali per B126-2X2

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Tripp Lite Commutatore a matrice

Tripp Lite

Tripp Lite B300-9X2-4K Manuale utente

Tripp Lite

Tripp Lite B119-2X2 Manuale utente

Tripp Lite

Tripp Lite B126-2X2 Manuale utente

Tripp Lite

Tripp Lite B119-4X2-4K Manuale utente

Tripp Lite

Tripp Lite NetDirector B060-032 Manuale utente

Tripp Lite

Tripp Lite NetDirector B060-016-2 Manuale utente

Tripp Lite

Tripp Lite B140-202 Manuale utente

Manuali Commutatore a matrice popolari di altre marche

Broadcast Tools

Broadcast Tools SS 8.2 Manuale utente

Altimium

Altimium MATF32 Manuale utente

ALFAtron

ALFAtron ALF-MUK44N Manuale utente

Monoprice

Monoprice Blackbird 15377 Manuale utente

Kramer

Kramer XL 3216VS Manuale utente

PTN

PTN FMX12 Manuale utente

CYP

CYP nT15GX01 Manuale utente

Kramer

Kramer VP-2x2 Manuale utente

Kramer

Kramer Sierra Video 6432V5xl Manuale utente

TESmart

TESmart HMA0402A40 Manuale utente

Octava

Octava HD4XSTPMX Manuale utente

Intelix

Intelix FLX-88 Istruzioni operative

Kramer

Kramer LASSEN XL 3232S Manuale utente

Roland

Roland XS-1HD Manuale utente

Kramer

Kramer VS-66HDCPxl Manuale utente

Atlona

Atlona AT-HDMI-22M Manuale utente

Link

Link HD8X8 Manuale utente

AMX

AMX AVS-OP-2020-117 Istruzioni e ricette