Trotec PPOS 10-20V Manuale utente
TRT-BA-PPOS10-20V-TC2020-09-001-EN
PPOS 10-20V
EN
ORIGINAL INSTRUCTIONS
CORDLESS POLISHER
2 EN
cordless polisher PPOS 10-20V
Table of contents
Notes regarding the instructions ..........................................2
Safety .....................................................................................2
Information about the device................................................7
Transport and storage...........................................................9
Start-up..................................................................................9
Operation .............................................................................11
Available accessories..........................................................12
Errors and faults..................................................................12
Maintenance ........................................................................13
Disposal ...............................................................................14
Declaration of conformity ...................................................14
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information
(e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Wear safety glasses
Information marked with this symbol indicates that you
should wear eye protection.
Wear a protective mask
Information marked with this symbol indicates that you
should wear a protective mask.
You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:
PPOS 10-20V
https://hub.trotec.com/?id=44253
Safety
General Power Tool Safety Warnings
Warning
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term power tool in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
General Power Tool Safety Warnings– Work area
safety
•Keep work area clean and well lit. Clutter or dark areas
invite accidents.
•Do not operate power tools in explosive atmosphere,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
•Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
EN 3
cordless polisher PPOS 10-20V
General Power Tool Safety Warnings– Electrical
safety
•Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
•Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
•Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
•Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
•If operating a power tool in a damp location is
unavoidable, use a residual current device(RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
General Power Tool Safety Warnings– Personal
safety
•Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
•Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
•Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
•Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situation.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
•If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
•Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
4 EN
cordless polisher PPOS 10-20V
General Power Tool Safety Warnings– Power tool
use and care
•Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
•Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
•Disconnect the plug from the power source and/or
remove the battery pack, if detachable, from the power
tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
•Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
•Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
•Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
•Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
General Power Tool Safety Warnings– Battery tool
use and care
•Recharge only with charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
•Use power tools only with specifically designed battery
packs. Use of any other battery packs may create a risk of
injury and fire.
•When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
•Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
•Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
•Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130°C may cause explosion.
•Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outsides the specified range may damage
the battery and increase the risk of fire.
General Power Tool Safety Warnings– Service
•Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
•Never service damaged battery pack. Service of battery
packs should only be performed by the manufacturer or
authorized service providers.
EN 5
cordless polisher PPOS 10-20V
Device-specific safety warnings for polishing
machines
•Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
•Hold onto the power tool with both hands. Position
your arms and your body in a way that allows you to
have the greatest control possible in order to absorb
kickback forces and reaction torques at high rotational
speeds.
•Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your
control.
•Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory could
snag your clothing and entangle the accessory in your
clothing.
•Use special care when working corners and sharp
edges. Avoid the accessory bouncing or getting stuck
in a corner. The result would be a loss of control or
kickback.
•Do not position your hand in the area next to the
rotating polishing wheel. In the event of a loss of control
or kickback, the rotating polishing wheel can hit your hand
and cause injuries.
•Make sure that the polishing bonnet is well attached
on the polishing disc. A loose polishing bonnet can slip
from the polishing disc, get entangled with your hand and
cause injuries.
•Only switch on the polishing machine once the
polishing disc completely rests on the area to be
polished.
•Do not use abrasives. Abrasives can damage the paint.
Dust particles hazardous to health can be
released during dry polishing. Always wear a
suitable dust mask to protect you from inhaling dust
particles.
Safety Warnings Specific for Polishing Operations
Make sure that no loose parts of the polishing bonnet, in
particular its attachment strings, spring freely. Clamp the
attachment strings or cut them to length. Loose and spinning
attachment strings can entangle your fingers or snag on the
workpiece.
Intended use
Only use the device PPOS 10-20V:
• for treating and refurbishing cars, boats, caravans,
motorcycles, floors or furniture.
• for polishing, waxing or dewaxing painted or chromium-
plated areas.
We recommend using the power tool with original Trotec
accessories.
Foreseeable misuse
The device is not suitable for grinding, sanding, wire brushing or
working with cutting wheels.
Any other use than the one described in the chapter "Intended
use" is regarded as reasonably foreseeable misuse.
Personnel qualifications
People who use this device must:
• have read and understood the instructions, especially the
Safety chapter.
6 EN
cordless polisher PPOS 10-20V
Personal protective equipment
Wear eye protection.
With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.
Wear a protective mask.
It saves you from inhaling harmful dusts generated
when processing workpieces.
Residual risks
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket and the battery from the device!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of explosive substances
Do not expose the battery to temperatures above
45°C! Do not let the battery come into contact with
water or fire! Avoid direct sunlight and moisture. There
is a risk of explosion!
Warning of hot surface
Some parts of this product can become very hot and
cause burns. Particular attention has to be given where
children and vulnerable people are present!
Warning
Toxic dusts!
The harmful / toxic dusts produced during operation
pose of risk to the health of the operator and persons
in the vicinity.
Wear eye protection and a dust mask!
Warning
Do not process materials containing asbestos.
Asbestos is considered carcinogenic.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Caution
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
Caution
Keep a sufficient distance from heat sources.
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
EN 7
cordless polisher PPOS 10-20V
Information about the device
Device description
The device PPOS 10-20V is suited for treating and refurbishing
cars, boats, caravans, motorcycles, floors, furniture and other
painted surfaces.
The device operates at an idle speed of 3000min-1. The large
polishing disc with Ø245mm provides for treating large
surfaces.
The supplied cloth polishing bonnet is ideally suited for applying
polishing agent, the synthetic fibre polishing bonnet serves for
polishing or dewaxing surfaces.
No polishing marks will occur thanks to eccentric motion.
The device is equipped with two handles for maximum surface
control. It allows for an even pressure distribution.
The battery comes with its own battery level indication. As a
result you can check the current charging status without having
to connect it to the device.
Device depiction
1
2
3
2
12
4
5
11
6
10
9
7
8
No. Designation
1On/off switch
2Handle
3Polishing disc
4Quick charger
5Red battery LED (battery charging)
6Battery
7Cloth polishing bonnet
8Synthetic fibre polishing bonnet
9Battery level indication
10 Release button
11 Green battery LED (quick charger ready for operation)
12 Battery holder
Scope of delivery
• 1x Cordless polisher PPOS 10-20V
• 1 x Rechargeable battery
• 1x Quick charger
• 1x Cloth polishing bonnet
• 1x Synthetic fibre polishing bonnet
• 1x Manual
8 EN
cordless polisher PPOS 10-20V
Technical data
Parameter Value
Model PPOS10-20V
Nominal voltage 20V
Idle speed 3000min-1
Diameter of polishing disc 245mm
Weight 2.0kg
Battery Multiflex20 – 2.0 DC
Type Li-ion
Nominal voltage 20 V
Capacity 2Ah
Quick charger Multiflex20 – 2.0 AC
Input
Nominal voltage 230 - 240V / 50Hz
Power input 65W
Output
Nominal voltage 21.5V
Charging current 2.4A
Fusing 3.15A (slow-blowing)
Charging time 1 h
Protection class II /
Vibration information according to EN62841
Vibration emission value ah9.15m/s2
Uncertainty K 1.5m/s2
Sound values according to EN62841
Sound pressure level LpA 66.4dB(A)
Sound power LWA 77.4dB(A)
Uncertainty K 3 dB
Information on noise and vibration:
• The specified total vibration and noise emission values
were measured by means of a test procedure standardized
in EN62841 and can be consulted for the comparison of
one power tool with another.
• The specified total vibration and noise emission values
can also be used for preliminary load assessment.
Caution
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
• The actual vibration and noise emission may differ from
the stated values during operation of the power tool. This
depends on how the power tool is used and especially on
the type of workpiece being processed. Try to keep the
vibration load to a minimum. Exemplary measures for
reducing the vibration load include wearing gloves during
operation of the tool and the limitation of working hours.
All parts of an operating cycle must be considered for this
(e.g. times at which the power tool is switched off and
times when it is switched on but runs without load).
EN 9
cordless polisher PPOS 10-20V
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
• Switch off the device.
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Allow the device to cool down.
• Remove the battery from the device.
• Remove the polishing bonnet from the device.
The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:
• The user may transport the batteries by road without any
additional requirements.
• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
– Only ship batteries if their housing is undamaged.
– Mask open terminals with tape and pack the battery in
a way that it cannot move inside the packaging.
– Please also observe any other national regulations.
Storage
Before storing the device, proceed as follows:
• Switch off the device.
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Allow the device to cool down.
• Remove the battery from the device.
• Remove the polishing bonnet from the polishing disc.
• Clean the device as described in the Maintenance chapter.
• Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• Ambient temperature below 45°C
• protected from dust and direct sunlight
• Store the device with the polishing disc facing upwards in
order for the polishing disc to maintain its shape.
Start-up
Unpacking the device
• Take the device and the accessories out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
• Check the contents for completeness and look for
damages.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
• Dispose of the packaging material according to the
national regulations.
10 EN
cordless polisher PPOS 10-20V
Charging the battery
Note
The battery can be damaged in case of improper
charging.
Remove the charger's mains plug before inserting or
removing the battery.
Never charge the battery at ambient temperatures
below 10°C or above 40°C.
The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.
Prior to initial start-up and when the battery is low (only the red
LED in the battery level indication(9) is illuminated), the battery
should be charged. To do so, please proceed as follows:
1. Slide the battery(6) onto the quick charger(4) upside
down until it locks in place.
1 h
6
4
11
5
9
2. Insert the mains plug of the quick charger(4) into a
properly fused mains socket.
ðThe red battery LED(5) lights up.
ðCharging requires approx. one hour.
3. Wait until the red battery LED(5) goes off and the green
battery LED(11) lights up.
ðThe battery(6) is fully charged.
4. Hold onto the mains plug while pulling the power cable of
the quick charger(4) out of the mains socket.
ðThe battery(6) and the quick charger(4) may have
become warm during charging.
Allow the battery(6) to cool down to room temperature.
5. Take the battery(6) out of the quick charger(4) by
pressing and holding the release button(10) and pulling
the battery(6) off the quick charger(4).
Inserting the battery
1. Slide the battery(6) onto the device until it locks in place.
6
Removing the battery
1. Detach the battery(6) from the device by pressing and
holding the unlocking button(10, I.) and pulling the battery
off the device(II.).
10
6
2. If required, charge the battery(6) as described in the
section Charging the battery.
Indice
Altri manuali Trotec Levigatrice
