TRU-BOLT 1742006 Manuale utente
M1742002 1742006 V1
Bluetooth Square Electronic Deadbolt
INDEX
I. INSTALLATION INSTRUCTIONS
Package Contents / Tools Required.....................................................Page 1
Prepare Door and Jamb.........................................................................Page 2
Adjusting Deadbolt Latch Set...............................................................Page 3
Installing Deadbolt Latch Set............................................................... Page 4
Preparing Interior Assembly.................................................................Page 5
Installing Exterior Assembly..................................................................Page 6
Installing Interior Assembly...................................................................Page 7-8
II. MOBILE APPLICATION INSTRUCTIONS
My Key Mobile™ Application Installation & Use / App Setup............Page 9
Add & Remove Locks / Using the App.................................................Page 10-11
Lock Settings..........................................................................................Page 11
eKey / Passcodes / Users / Records...................................................Page 12-15
Main Menu..............................................................................................Page 16
III. PHYSICAL KEYPAD OPERATION AND INSTRUCTIONS
Exterior Assembly Overview.................................................................Page 17
Turn On/Off Auto Lock Function / Sound Off / Sound On /
Restore Factory Settings.....................................................................Page 18
Add Administrator / Customize Passcodes Received from the App /
Enable/Disable Auto-Lock / Vacation Mode /
Disable Vacation Mode.........................................................................Page 19
IV. ASSISTANCE
Consumer Friendly Message Guide / Programming Records..........Page 20
Installation Trouble Shooting ..............................................................Page 21
Template ................................................................................................Page 23-24
Consumer Assistance...........................................................................Page 25
FCC Regulatory Compliance................................................................Page 26
Limited Warranty....................................................................................Page 27
Page 1
I. INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS
TOOLS REQUIRED
Tools Required for Installation on Pre-drilled Doors:
• Phillips Screwdriver
NOTE: DO NOT USE a drill.
Tools Required for Installation
on Doors That Require Drilling:
• Drill
• Tape Measure
• Pencil
• 2-1/8” (54mm) Drill Hole Saw
• 1” (25mm) Drill
• 1/16” (2mm) Drill
• Chisel
• Hammer
• Phillips Screwdriver
DO NOT RETURN TO STORE! If any parts are missing or damaged,
please call Customer Service toll free at 1-800-860-1677 (Toll Free, M-F 7am – 5pm PST)
Online installation videos can be viewed at TruBoltLocks.info
Exterior Assembly
Entry keys (2 ea.)
Mounting Plate
Interior Assembly
Deadbolt Strike Plate
Deadbolt Latch Set (Adjustable)
2-3/8” (60mm) to 2-3/4” (70mm)
Electronic lock requires (4) High Quality
AA Alkaline batteries. When all 4 batteries
are installed in the correct position, hear 2
beeps and the keypad will illuminate blue.
DO NOT TOUCH the keypad until the keypad
stops illuminating.
BATTERIES (NOT INCLUDED)
PAY CLOSE ATTENTION TO ALERTS
3/4” (19mm) Screws - 5 ea. 1” (25mm) Screw - 1 ea.
5/16” (8mm) Screws - 2 ea. 7/8” (22mm) Screws - 2 ea.
A
C
B
D
Page 2
NOTE: For installation on doors with pre-drilled holes skip to page 4.
1. TEMPLATE
a. Cut out template printed on page 15 & 16 of this Manual
(Figure 1a).
b. Fold template and place on door 36” (915mm) from
the ground as marked (Figure 1b).
2. MARK THE DOOR FOR DRILLING
b. Mark center hole on door edge through guide on
template for 1” (25mm) latch bolt (Figure 2a).
a. Mark center hole on door face through guide on
template for 2-3/8” (60mm) or 2-3/4” (70mm)
backset (Figure 2b).
3. DRILL AND CHISEL DOOR
a. Drill 2-1/8” (54mm) hole through door face as marked
for lock set (Figure 3a).
b. Drill 1” (25mm) hole in center of door edge for
Deadbolt Latch Assembly (Figure 3b).
c. Insert Deadbolt Latch Assembly in hole keeping it
parallel to face of door. Mark outline and remove latch
(Figure 3c).
d. Chisel 1/8” (3mm) deep or until latch face is ush
with door edge (Figure 3d).
4. MARK AND DRILL DOOR JAMB
a. Mark center hole on edge of jamb even with the center of the Latch Bolt on door
edge. (Figure 4a).
b. Drill 1” (25mm) hole 1-3/16” (30mm) deep in door jamb on center mark
(Figure 4b).
c. Outline outside edges of Strike Plate (Figure 4c).
d. Chisel 1/8” (3mm) deep for Strike Plate or until ush (Figure 4d).
e. Install Strike Plate using two 3/4” (19mm) screws provided (Figure 4e).
PREPARE DOOR AND JAMB
Figure 4a Figure 4b Figure 4c Figure 4e
Figure 4d
NOTE: For Drive in Latch, drill hole size indicated on template and press
until it is ush with door edge.
UP
Figure 1a
Figure 2a Figure 2b
Figure 3a
Figure 3c
Figure 1b
Figure 3b
Figure 3d
Page 3
ADJUSTING DEADBOLT LATCH SET
NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm)
Measure the backset (backset is distance between edge of the door and the
center of Lock).
1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET
a. Hold latch with numbers facing forward and thumb pressing on the bolt (Figure 1a).
b. Rotate the cylinder cover clockwise (Figure 1b).
c. Pull and twist the extension plate all the way out (Figure 1c).
d. Rotate the cylinder cover counter clockwise so that the marking aligns with
the 2-3/4” (70mm) position indicator (Figure 1d).
2. TO CONVERT FROM 2-3/4” (70mm) BACKSET TO 2-3/8” (60mm) BACKSET
a. Hold latch with numbers facing forward and thumb pressing on the bolt (Figure 2a).
b. Rotate the cylinder cover clockwise (Figure 2b).
c. Push and twist the extension plate all the way in (Figure 2c).
d. Rotate the cylinder cover counter clockwise so that the marking aligns with
the 2-3/8” (60mm) position indicator (Figure 2d).
Figure 1a Figure 1b
Figure 1c
Your latch is now set 2-3/4” (70mm) backset
Cylindrical Cover Extension Plate
2-3/8”
(60mm) 2-3/8”
(60mm)
2-3/4”
(70mm)
Figure 1d
Figure 2a Figure 2b Your latch is now set 2-3/8” (60mm) backset
Cylindrical Cover Extension Plate
2-3/8”
(60mm) 2-3/8”
(60mm)
Figure 2c
Figure 2d
NOTE: Do not extend Cylindrical Cover past 2-3/4” (70mm)
Page 4
3. INSTALLING THE DEADBOLT LATCH SET (need phillips head screwdriver)
a. Insert Deadbolt Latch Set into door edge hole with the word
“UP” and the arrow on the extension plate facing UP. Cross
shaped spindle connector will be at the bottom of the Deadbolt
Latch Set (Figure 3a).
b. Make sure the face plate sits ush with the door. Do not force
the latch into the mortise ush. Chisel out excess material if
necessary for a ush t.
c. Using two 3/4” (19mm). screws provided, screw the latch into the
door with a hand held screwdriver. DO NOT OVER TIGHTEN.
4. IDENTIFYING YOUR DOOR HANDING
Stand outside the door.
a. If the hinges are on the left your door is Left Handed (Figure 4a and 4b).
b. If the hinges are on the right your door is Right Handed (Figure 4a and 4b).
INSTALLING DEADBOLT LATCH SET
Figure 3a
Deadbolt Latch Extended Deadbolt Latch Retracted
NOTE: Deadbolt Latch must be retracted when installing
NOTE: You are standing outside the door
OUT SWING DOOR IN SWING DOOR
Figure 4a
Left Handed Door
Hinges are on the left side
Left Handed Door
Hinges are on the left side
Right Handed Door
Hinges are on the right side
Right Handed Door
Hinges are on the right side
Figure 4b
Page 5
6. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR
a. Gently move the switch to “L” for Left Handed Door (Figure 6a).
b. Gently move the Switch to “R” for Right Handed Door (Figure 6b).
7. SET THE INTERIOR KNOB POSITION FOR LEFT OR RIGHT HAND HINGED DOORS
a. The Interior Knob goes in the Horizontal position for Left Handed Doors (Figure 7a).
b. The Interior Knob goes in the Vertical position for Right Handed Doors (Figure 7b).
PREPARING THE INTERIOR ASSEMBLY
NOTE: Make sure deadbolt Latch is retracted
5. UNPACK THE INTERIOR ASSEMBLY
a. Remove the battery cover by sliding the cover upward.
b. Locate the screws holding the Mounting Plate to the Interior Assembly. Remove the
screws to release the Mounting Plate from the Interior Assembly.
Entry Switch
(Left or Right)
Figure 6a-b
Right Handed Door
(Vertical)
Left Handed Door
(Horizontal)
Figure 7a Figure 7b
Page 6
9. SECURING THE EXTERIOR ASSEMBLY TO THE DOOR
a. From the side marked “This side against
door”, route the Control Wire through the
rectangular slot in the Mounting Plate (Figure 9a).
b. Place Mounting Plate against door with tailpiece passing
through the center hole in the three hole set (Figure 9b).
c. Secure the Mounting Plate to the Exterior Assembly using
two 7/8” (22mm) Screws(B) (Figure 9c).
d. Hand tighten with a Phillips Screwdriver leaving loosely
connected (Figure 9d).
e. Check that the Rubber Gasket is properly aligned and correct as necessary
(Figure 8a).
f. Check vertical alignment of the lock (Figure 9f).
g. Tighten securely with a hand held Phillips Screwdriver. DO NOT OVER TIGHTEN
10. OPTIONAL INSTALLATION
a. Using a 1/16” (2mm) drill bit, drill a pilot hole in your door using the
Mounting Plate upper hole as a guide (Figure 10a).
b. Insert one 3/4” (19mm) screw(C) and tighten.
8. INSTALLING THE EXTERIOR ASSEMBLY
Work with the Door Open for easy access.
a. Unpack the Exterior Assembly. Use care to not scratch the green circuit board
during handling and installation.
b. Check that the Rubber Gasket is properly seated on the Exterior Assembly (Figure 8a).
c. Insert the Exterior Assembly onto the door with the tailpiece going through the
Deadbolt Latch Set cross shaped spindle connector in the VERTICAL POSITION.
Route the Control Wire through the door under the Deadbolt Latch Set (Figure 8c).
NOTE: Tailpiece must
be positioned vertically
INSTALLING EXTERIOR ASSEMBLY
Control
Wire
Tailpiece (Vertical)
Latch
Hole
Figure 8c
Figure 10a
NOTE: Lock and unlock using the key to see if
the Deadbolt Latch is opening and closing easily.
Figure 8a
Rubber Gasket
Right handed door view
Mounting Plate
C - 3/4” (19mm) screw
(Optional)
B - 7/8” (22mm)
screws
Control Wire
Figure 9a-f
Page 7
INSTALLING INTERIOR ASSEMBLY
11. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY
a. Use care to attach the Control Wire male plug to the Interior Assembly female
socket connector.
b. Carefully insert the male plug, smooth side up, into the female socket on the
interior assembly. DO NOT FORCE! (Figure 11a).
12. ATTACH THE INTERIOR ASSEMBLY TO DOOR
a. IMPORTANT: Make sure the knob is in the vertical position for right hand door and
horizontal position for left hand door.
b. Make sure the tailpiece (Figure 12a) is in the vertical position.
c. Position the Interior Assembly over the vertically positioned tailpiece and carefully
push the Interior Assembly against the door (Figure 12a).
d. Using two 5/16” (8mm) screws and one 1” (25mm) screw, attach
the Interior Assembly to the Mounting Plate. DO NOT OVER TIGHTEN SCREWS
NOTE: Lock and unlock using Interior Knob to see if the
latch is opening and closing easily.
Match
Color
Figure 11a
Vertical Tailpiece
Figure 12a
A - 5/16”(8mm) screws
D - 1”(25mm) screw
Page 8
13. Installing Batteries
a. Slide battery cover up and remove.
b. Insert 4 AA high quality Alkaline batteries into the Battery Compartment in the
direction noted +/- on the Compartment. The Lock will beep 2 times, the keypad
will illuminate blue, and the Tru-Bolt button will ash green twice to signify that
it has received power (Figure 13a).
c. Replace battery cover and slide down on to the Interior Assembly to cover the
batteries (Figure 13b).
14. Testing Lock
a. Always test with the Door Open
b. Test the Lock using the Interior Knob. The bolt should move smoothly in and out.
c. Test the Lock using the Keypad. To lock press and then press “1234”
to unlock.
INSTALLING INTERIOR ASSEMBLY (CONT.)
Battery
Cover
4 AA
Batteries
NOTE: Do not touch the Keypad until the blue light turns off.
Do not use rechargeable batteries or non-alkaline batteries.
Figure 13a-b
INSTALLATION OVERVIEW
Strike Plate
Mounting Plate
C - Optional
3/4”(19mm)
Interior Assembly
Battery Cover
A - 5/16”(8mm) screws
D - 1”(25mm) screw
B - 7/8”(22mm) screws
Latch
Vertical Tailpiece
Exterior Assembly
Rubber Gasket
Control Wire
Keys
C - 3/4”(19mm)
screws
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali TRU-BOLT Serratura della porta
