Truetone 1 SPOT Pro CS7 Manuale utente
www.Truetone.com
IMPORTANT SAFETY INSTRUCTIONS
1. All the safety and operatin instructions should be read before this
product is operated. Keep these instructions for future reference.
2. Pay attention to all warnin s on the power supply and in the operatin
instructions.
3. WARNING: Do not use this device near water or any other liquid.
4. Clean only with dry cloth.
5. Do not block any ventilation openin s.
6. Do not use this device near any heat sources.
7. Do not remove the power plu roundin pin on the input cable.
8. Protect all input and output power cables from bein walked on or
pinched.
9. Only use attachments/accessories specified by the manufacturer.
10. Use only with the brackets and screws provided with this power
supply.
11. Unplu this device durin li htnin storms or when unused for lon
periods of time.
12. Refer all repairs to qualified personnel at Truetone or an authorized
Truetone distributor. Under no circumstances should the power
supply be opened by the user.
13. This li htnin flash with arrowhead symbol within an equilateral
trian le is intended to alert the user to the presence of non-insulated
“dan erous volta e” within the product’s enclosure that may be of
sufficient ma nitude to constitute a risk of electric shock.
- WARNING: To reduce the risk of electric shock, do not remove cover
(or back) as there are no user-serviceable parts inside. Refer
servicin to qualified personnel.
- The exclamation point within an equilateral trian le is intended to
alert the user to the presence of important operatin and
maintenance instructions in the literature accompanyin the
appliance.
14. The maximum ambient temperature should not exceed 35 de ree C.
15. Date code: YYMM, YY means year, MM means month. For example:
1412 represents Year 2014, December.
Owners Manual
Need some reat pedals to o
with your 1 SPOT Pro?
Check out Truetone
*
pedals at
Truetone.com
* Truetone was formerly known as Visual Sound; the makers
of Jekyll & Hyde, Route 66, H2O, Visual Volume and
The 1 SPOT!
Mounting your 1 SPOT Pro under a Pedaltrain
®
pedalboard:
The 1 SPOT Pro comes with 2 metal brackets, 4 black machine screws and 4
silver thread-formin screws. The black machine screws are for attachin the
metal brackets to the sides of the 1 SPOT Pro, and the thread-formin screws
are for attachin the brackets to the Pedaltrain
®
, as shown below. There is no
need to pre-drill holes for the screws if you are usin a powered screwdriver.
Make sure the 1 SPOT Pro is
slanted durin mountin , so that
the IEC input socket is in between the
rails of the Pedaltrain. To help position it
correctly, you can put a 9V battery under the
1 SPOT Pro (center-back of the unit), which
will raise the back to the proper hei ht the
battery is only actin as a temporary spacer.
After the 4 thread-formin screws are installed, push the 9V battery out.
Con ratulations on your purchase of the 1 SPOT Pro CS7 Power Supply by
Truetone! The 1 SPOT Pro CS7 provides 7 outputs to power just about any
effect pedal. All 7 outputs are completely isolated, re ulated, and filtered to
provide quiet and safe operation for your valuable effects pedals.
The 1 SPOT Pro CS7 contains the following:
1 SPOT Pro CS7 Power Supply
Power cables:
(4) DC18 (5.5x2.1mm barrel plu s; 18” (457mm) – White
(3) DC12 (5.5x2.1mm barrel plu s; 12” (305mm) – Yellow
Converter Plu s:
(1) CL6 – Green
(1) CYR – Red
(1) C35 – Black
(1) CBAT – Black battery clip
The proper powerin of effects pedals is much misunderstood, but necessary
knowled e that every effect user must have. It is the difference between proper
functionality of your pedal, or potentially dama e to it. To properly use the 1
SPOT Pro CS7 alon with your effects devices, you must know both the power
requirements of your pedals, and the capabilities of the 1 SPOT Pro CS7 power
supply. We will concentrate on the latter first.
Specifications of the 1 SPOT Pro CS7:
Input: 100-240V~, 50/60Hz, 0.55A (Worldwide input volta e)
Outputs: 7 Outputs are as shown below: (Outputs 2-5 are switchable)
1 2 3 4 5 6 7
Note: These numbers do not
appear on the actual unit.
Note: This symbol
indicates DC volta e.
The bottom panel of the 1 SPOT Pro CS7 contains 4-mini switches that chan e
the volta e output of outputs 2-5.
Switch 1 corresponds to Output-2 and allows it to be switched between
either 9Vdc (OFF) or 12Vdc (ON) at 200mA
Switch 2 corresponds to Output-3 and allows it to be switched between
either 9Vdc (OFF) or 12Vdc (ON) at 200mA
Switch corresponds to Output-4 and allows it to be switched between
either 9Vdc (OFF) or 12Vdc (ON) at 200mA
Switch 4 corresponds to Output-5 and allows it to be switched between
either 9Vdc (OFF) or 12Vdc (ON) at 200mA
Voltage Input:
The 1 SPOT Pro CS7 can be used anywhere in the world without the use of a
step-up or step-down transformer. Like our 1 SPOT, it transforms wall volta e from
100-240Vac, and converts it into the stated volta es on the front panel on the unit.
Which output and settings do I use for my pedals?
It is important for you to know the power requirements for your pedal. For every
pedal that you are oin to power via the 1 SPOT Pro CS7, you need to know the
followin :
1. What is the volta e required by the pedal?
2. Does the pedal require AC or DC volta e?
3. What is the polarity of the pedal? (Center pin positive or ne ative.)
These questions can usually be answered by:
1. Inspectin the pedal itself near the power jack.
2. Referrin to the owner’s manual.
3. Checkin online, or contactin the manufacturer
4. If your pedal can be powered by a 9Vdc battery, it can be powered by one
of the 9Vdc outputs (exception bein the Boss ACA pedals, see below).
Notes on certain pedals:
• Some older Boss pedals require 12Vdc, yet can be powered by a 9Vdc
battery. They will indicate “Use ACA adaptor” near the power jack. To
power an ACA pedal please use outputs 2-5, and set to 12Vdc on the dip
switch for the correspondin output. Modern Boss pedals will indicate
“PSA,” and can be powered by any of the 1 SPOT Pro CS7’s 9Vdc
outputs.
• Many ermanium based fuzzes and Octavia-style pedals will require the
use of the CYR adaptor to reverse the polarity to center pin positive.
•
For pedals with hi h milliamp draws such as Strymon please utilize outputs
6 or 7 that produce 500mA each.
• Eventide pedals such as the Time Factor and H9 may be powered by
outputs 6 or 7 with the addition of the CL6 converter, for proper dc jack tip
size and polarity.
• Line 6 M5 may be powered by outputs 6 or 7.
• Line 6 M9, and the modelin pedals (DL-4/MM-4), may be powered by
outputs 6 or 7, and will also require the CL6 converter.
• Line 6 Tone Core pedals may be powered by any 9Vdc output.
• Line 6 POD or M13 cannot be powered by the 1 SPOT Pro CS7.
• If more 9Vdc pedals need to be powered, a MC5 daisy chain (sold
separately) may be plu ed into any of the 9Vdc outputs dependin on mA
draw.
• Pedals that do not utilize a power jack, yet are powered normally by a 9Vdc
battery, may utilize any 9Vdc output, alon with the CBAT converter.
• TC Electronic Nova pedals may be powered by outputs 2-5 in the 12Vdc
position.
• TC Electronic Classic and Tone Print series may be powered by any 9Vdc
output.
• Di itech Whammy: Versions 1-4 cannot be powered by the 1 SPOT Pro
CS7. Version 5 or Whammy DT may be powered by ouputs 6 or 7.
Warranty:
The 1 SPOT Pro CS7 carries a 5-year warranty to the ori inal owner, coverin
faulty materials and workmanship.
The warranty is considered void for any of the followin reasons:
1. The unit has been modified in any way.
2. Any repair has been attempted by anyone other than the manufacturer.
If your unit becomes defective durin the warranty period, please contact
Truetone to obtain a return authorization. All contact information can be found
at Truetone.com
WARNING: Operation contrary to the uidelines set forth in this manual may
dama e your pedals. Truetone is not responsible for the damage of your
pedals by improper usage.
Input Power Cable:
Your 1 SPOT Pro includes an input power cable. Insert the universal IEC plu
into the socket on the back of the 1 SPOT pro. Plu the other end into a wall
outlet or power strip.
FCC Notice:
Note: This equipment has been tested and found to comply with the limits for a Class B di ital
device, pursuant to part 15 of the FCC Rules. These limits are desi ned to provide reasonable
protection a ainst harmful interference in a residential installation. This equipment enerates, uses
and can radiate radio frequency ener y and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
uarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turnin the
equipment off and on, the user is encoura ed to try to correct the interference by one or more of the
followin measures:
— Reorient or relocate the receivin antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Altri manuali Truetone Alimentazione elettrica
