Trust ZCM-300 Manuale utente
ZIGBEE Smart Build-in Dimmer
ZCM-300
USER MANUAL
Item 71317 Version 1.0
Always read the instructions
before using this product
PREMIUM-LINE
ZCM-300 SWITCH-IN
2
ZCM-300 BUILD-IN DIMMER
1
3
2
4
6B
L
i
v
e
w
i
r
e
(
b
r
o
w
n
)
L
i
v
e
w
i
r
e
(
b
r
o
w
n
)
LS L N N
join mode
LED
3
ZCM-300 BUILD-IN DIMMER
5
7
6A
6B
PP
L
N
Wall Switch
Wall Switch
L NS N
L
P
L
N
Wall Switch
L NS N
L
L
i
v
e
w
i
r
e
(
b
r
o
w
n
)
N
e
u
t
r
a
l
w
i
r
e
(
b
l
u
e
)
S
w
i
t
c
h
w
i
r
e
(
b
l
a
c
k
)
LS L N N
join mode
Trust Smart Home Switch-in
4
ZCM-300 BUILD-IN DIMMER
A
9
10
8
LS L N N
join mode
5
5
7
6
8
ZCM-300 BUILD-IN DIMMER
11
12
LS L N N
join mode
5 sec
LS L N N
join mode
LED
Dimming mode
LED flashes 1x red: Leading Edge
LED flashes 2x red: Trailing Edge
LED flashes 3x red: Filament LED mode
A
A
CB
Turn lamp ON
at 100% brightness
LS L N N
join mode
LS L N N
join mode
3 sec Short
6
1
3 4
ZCM-300 BUILD-IN DIMMER
D
LS L N N
join mode
3 sec
Position 4
Position 3
Position 2
Position 1
LS L N N
join mode
1 sec
13
7
5
7
6
8
ZCM-300 BUILD-IN DIMMER
LS L N N
join mode
6 sec
RESET
LS L N N
join mode
1 sec
8
EN ZCM-300 BUILD-IN DIMMER
1. Turn OFF mains power
Always turn OFF the power (in the fuse box) before
installing or removing this product. The ZCM-300 can
be used for two wall switches connected to one lamp
(stairwell/hotel circuit) or for a single wall switch connected
to one lamp.
2. Loosen ceiling lights
Remove the existing lighting from the ceiling and leave
the wires connected to the lighting. The lighting must not
exceed the maximum wattage. If no live wire (brown)
is present, it must be pulled. If in doubt, consult an
electrician.
3. Disconnect the switch wire (black) and neutral
wire (blue)
To install the ZCM-300, disconnect the switch wire (black)
and neutral wire (blue) from the lamp. (Disconnect terminal
block or cut wires if necessary) If in doubt about wire
colors, consult an electrician.
4. Connect the live wire to a terminal block
Connect the live wire (brown) from the ceiling box to a
terminal block. Also connect the other end of the live wire
(brown) to same terminal block.
5. Connect the wires to the module
Connect the neutral wire (blue) from the
ceiling box to the outer [N] contact of the module.
Optional: The S-contact does not need to be connected.
Connect the switch wire (black) from the ceiling box with
the [S] terminal if you want to (continue to) make use of a
wall switch. Connect the neutral wire (blue) of the lamp
with the center [N] contact.
Connect the switch wire (black) of the lamp
to the [ L
L
] contact. Connect one new live wire (brown)
from the terminal block to the [L] terminal.
Tighten the terminal screws securely.
6A. Double wall switch installation diagram
This is the technical installation diagram of the ZCM-300
with two wall switches (hotel / stairwell circuit).
6B. Single wall switch installation diagram
This is the technical installation diagram of the ZCM-300
with one wall switch.
7. Download App
Download and install the Trust Smart Home Switch-in App
from the Google Playstore or App Store to connect the
dimmer to an Smart Bridge or ICS-2000.
8. Switch on the mains voltage
Turn on the power before proceeding with the installation.
Do not touch any stripped parts of the wires after this
step. The LED indicator on the module will flash for 60s
when power is on to indicate it is in connect mode
9. Connect Module
ASelect a room in the App.
Press the + button and choose Trust Smart Home. Press
Premium Line and choose built-in dimmer. Then follow the
steps in the App.
10. Optional: Also connect with Zigbee remote
control
Go to www.trust.com/faq for more information on how the
dimmer can be connected with a zigbee remote control.
9
EN
ZCM-300 BUILD-IN DIMMER
11. Dimming Mode
If your lighting flickers, you can choose a dierent dimming
mode:
ATurn o the module with the App or remote control.
Press and hold the mode button for 5 seconds until the
LED flashes red and then release.
The LED flashes red 1x for the Leading edge mode:
This mode is most suitable for dimmable incandescent,
halogen, lamps with a traditional (wound) dimmable
transformer and some specific LED lamps
Press 5 seconds again to go to the next dimming mode
For the Trailing edge mode, the LED flashes red 2x: This
mode is most suitable for LED lamps and lamps with an
electronic dimmable transformer.
Press 5 seconds again to go to the next dimming mode
For the Filament LED lamp mode, the LED flashes 3x red:
This mode is intended for dimming Filament LED lamps
Activate dimming sequence with 230V wall switch
To activate the dimming sequence with a 230V wall
switch, first switch the module ON with the wall switch.
Then quickly turn the wall switch OFF and ON again. To
lock the dimming level, quickly turn the wall switch OFF
and ON again.
12. Adjust dimming range
If the connected lighting flickers in then lowest dim level or
does not dim deep enough, you can adjust the lower limit
of the dimming range.
ATurn on the lamp and set it to 100% brightness.
BPress and hold the join button for 3 sec. The lamp
will go to the lowest brightness. Then release the join
button.
CShort press the join button to decrease the minimum
brightness.
The minimum brightness starts at position 4. Every time
the join button is pressed shortly, the lamp will dim 1
position deeper (4-3-2-1). If you shortly press the join
button again after setting 1, the minimum dim setting will
increase again (1-2-3-4).
DPress and hold the join button again for 3 seconds
when the correct dim position has been selected. The lamp
will flash 2x to confirm the selected dimming position.
As soon as the lamp starts flashing, the button can be
released.
13. Install module
First check whether the lighting dims properly.
Place the dimmer in the ceiling box. Reinstall the lamp.
Make sure that you can always reach the built-in dimmer,
for example to reset it or to reconnect it.
Activate connection mode
If the ZCM-300 is not connected to an Smart Bridge or ICS-
2000, you can enter the connection mode by pressing the
join button shortly on the module. The LED will flash slowly
for 60s to indicate it is in connect mode
Reset ZCM-300
Warning: This step removes the module from the Smart
Bridge or ICS-2000 or the ZYCT-202. To reset the dimmer,
press the join button for 6 seconds. The LED will flash
quickly. Shortly press the button again. The connected
lamp will go ON-OFF-ON-OFF to confirm the reset and then
enter connect mode.
10
NL ZCM-300 BUILD-IN DIMMER
1. Stroomvoorziening uitschakelen
Schakel altijd de stroomvoorziening UIT (in de
zekeringkast) voordat u begint met de installatie of
verwijdering van dit product. De ZCM-300 kan worden
gebruikt voor twee wandschakelaars die zijn verbonden
met één lamp (trappenhuis / hotelcircuit) of voor één
enkele wandschakelaar die op één lamp is aangesloten.
2. Maak plafondverlichting los
Verwijder de bestaande verlichting van het plafond en laat
de draden aangesloten op de verlichting. De verlichting
mag het maximale wattage niet overschrijden. Als er
geen fasedraad (bruin) aanwezig is, moet deze worden
getrokken. Raadpleeg een elektricien als u twijfelt.
3. Ontkoppel de schakeldraad (zwart) en de
nuldraad (blauw)
Om de ZCM-300 te installeren, ontkoppelt u de
schakeldraad (zwart) en de nuldraad (blauw) van de lamp.
(Loskoppelen van het kroonsteentje of knip de draden
indien nodig door) Raadpleeg een elektricien als u twijfelt
over de draadkleuren.
4. Sluit de fasedraad aan op een
lasklem
Sluit de fasedraad (bruin) van de plafonddoos aan op een
lasklem. Sluit het andere uiteinde van de fasedraad (bruin)
ook weer aan op dezelfde lasklem.
5. Verbind de draden met de module
• Verbind de nuldraad (blauw) uit de
plafonddoos met het buitenste [N] contact
van de module.
• Optioneel: Het S-contact hoeft niet aangesloten
te worden. Verbind de schakeldraad (zwart) uit
de plafonddoos met het [S] contact als u gebruik
wilt (blijven) maken van een wandschakelaar.
• Verbind de nuldraad (blauw) van de lamp
met het middelste [N] contact.
• Sluit de schakeldraad (zwart) van de lamp
aan op het [ L
L
] contact.
• Sluit één nieuwe fasedraad (bruin) van de
lasklem aan op het [L] contact.
• Draai de aansluitingsschroeven stevig vast.
6A. Installatieschema dubbele wandschakelaar
Dit is het technische installatieschema van de ZCM-300
met twee wandschakelaars (hotel / trappenhuiscircuit).
6B. Installatieschema enkele wandschakelaar
Dit is het technische installatieschema van de ZCM-300
met een wandschakelaar.
7. Download App
Download en installeer de Trust Smart Home Switch-in
App uit de Google Playstore of App Store om de dimmer te
verbinden met een Smart Bridge of ICS-2000.
8. Schakel de netspanning in
Schakel de netspanning in voordat u doorgaat met de
installatie Zorg dat na deze stap geen gestripte
delen van de draden worden aangeraakt. De LED-
indicator op de module zal 60 sec knipperen wanneer de
spanning is ingeschakeld om aan te geven dat deze in de
verbindmodus zit.
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Trust Dimmer
Trust
Trust START-LINE ACC-250-LD Manuale utente
Trust
Trust START-LINE ACD-200 Manuale utente
Trust
Trust START-LINE ACM-250-LD Manuale utente
Trust
Trust 300 Series Manuale utente
Trust
Trust START-LINE RECEIVER AGC-200 Manuale utente
Trust
Trust START-LINE ACD-200 Manuale utente
Trust
Trust 300DM Manuale utente
Trust
Trust START-LINE ACC-250-LD Manuale utente
