10
Electric safety can be improved by application of a residual current device
(RDA) with the residual current of 30 mA.
OPERATION:
nSwitching the device on and off
To switch the device on and off one has to use the trigger (6) (see Fig. D).
The desired operation mode of the device (blowing or suction) should be
selected before the machine is switched on.
PREPARATION FOR OPERATION: nSelection of the operation mode
The blower is delivered partly assembled in a transportation package. The operation mode can be selected with use of the dedicated selector
After having the device unpacked check completeness of the kit and fit switch (8).
the non-assembled parts in accordance with the manual. To switch the device over to the mode of «Collection and chopping» the
NOTE: Prior to any assembly of adjustment operations selector switch must be rotated to the symbol of «suction» ( Fig. B).
make sure that the device is unplugged from the In order to select the operation mode of «Blowing» set the selector
electric power network. switch next to the symbol of «blowing» (see Fig. C).
UNPACKING AND ASSEMBLY: NOTE! Prior to switching the device over to the blowing mode the operator
must empty the waste bag. Otherwise the already collected wastes may be
WARNING! Operation of the blower is not allowed when the pipe or the
blown out from the bag.
waste bag are not in place.
nInstallation of the blowing and suction pipe nAdjustment of the blowing /suction pressure
Blowing /suction pressure can be adjusted with use of the rotation speed
1. Connect the bottom part (1) of the pipe with its top part (2) by
control knob (4). Rotation speed can be infinitely varied within the range
pushing the bottom part into the top one until locking. The connected
from 8000 to 14000 rpm. To select the necessary rotation speed the
parts must be secured with used of two screws (14) (see Fig. A).
control knob should be set accordingly against the scale from 1 to 6.
2. Insert the assembled pipe into the device housing and secure against
It is reasonable to set the rotation speed as low as is indispensable if
unintentional disconnection by means of two screws (14) (see Fig. A).
higher values of rpm are not necessary.
To disconnect the pipe it is first necessary to unscrew the fixing screws.
nGeneral rules for the device operation
NOTE! Prior to dismantling the pipe the machine must
be switched off and disconnected from the source of NOTE! Prior to switching the blower on hold it firmly with two hands.
electric power. Length of the shoulder belt should be accordingly adjusted so that the
pipe is guided right above the ground level. In order to alleviate
nInstallation of the waste bag (see Fig. A)encumbrance to the operator and to facilitate guiding of the pipe on the
Suspend the bag lug on the hook attached to the pipe. Then slide the bag ground, the device is provided with wheels (12) attached to the pipe
inlet sleeve onto the discharge nozzle (9) until locking. bottom end (see Fig. F – G).
To detach the waste bag (10) gently squeeze the locking pins of the The garden vac/blower must be operated in strict adherence to relevant
sleeve, unlock the clamp and slide out the inlet sleeve of the bag. instructions and guidelines contained in this User Manual. The machine
nAttachment of the shoulder belt (see Fig. A)is designed with the purpose to enable its operation by operators
Snap the shoulder belt (13) to its lug on the main handle and adjust its standing upright. Any other position of the operator's body is
length as desired. inappropriate and is associated with possible injuries. Do never switch
the blower on when it lies on its side or is put upside down.
CONNECTION TO THE ELECTRIC NETWORK:
nEmptying the waste bag
The blower is designed for operation with power voltage from the 230-In order to maintain high suction pressure and enable effortless
240 V electric grid. Do never attempt to supply the device from another operation of the device it is recommended to empty the waste bag (10)
voltage source. every time when it is half-full. It helps to maintain low total weight of the
Prior to connecting the device make sure that parameters of the device device and full suction pressure of the device.
specified on its rating plate correspond to the ones of the voltage source. Prior to emptying the bag it is necessary to switch the blower off and
NOTE! Check condition of the power cord before plugging it into the electric unplug the power cord form the electric outlet. Take the bag out of the
outlet. Operation of the device with faulty or damaged power cord is blower and empty its content by unfastening the zip (11) placed at the
forbidden. bottom of the bag. Prior to reinstallation of the bag clean the discharge
nExtension cable nozzle (9) of the blower housing. Remember to fasten the zip back before
While working with the blower on the open area it is necessary to use the blower is switched on.
appropriate electric extension cables purposefully dedicated for such
applications. To avoid unintended disconnection of the electric line make
NOTE! Prior to commencement of any maintenance jobs, switch the device
a loop at the end of the extension cable (16) and attach it to the
off and make sure that it is disconnected from the source of power voltage.
dedicated bracket (15) according to Fig. E. Operators should put the
extension cable over a shoulder to the back and pay attention to always WARNING! Take care to avoid moistening of the blower. Do never spray it
keep the cable behind the machine (see Fig. F). with water.
STORAGE AND MAINTENANCE:
Sound pressure level (LpA)
Sound power level (LwA)
Guaranteed sound power level (LwA)
Average vibrations
,2
(measuring tolerance – 1 5m/s )
93,2 dB(A)
104,2 dB(A)
3 dB(A)
2
2,291 m/s
Measuring tolerance K K
LpA, LwA
106 dB(A)
