Tyco Electronics 2063195-1 Manuale utente
Instruction Sheet
SDE PE -12 Commercial
Hand Tool Assembly 2063195-1 408-10224
LOC B
1
of 5
E
2008 Tyco Electronics Corporation, Harrisburg, A
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
TOOLING ASSISTANCE CENTER 1-800-722-1111
RODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
10 JUN 08 Rev A
with Die Assembly 2063195-2
PROPER USE GUIDELINES
CumulativeTraumaDisorderscanresultfromthe prolongeduseofmanually poweredhandtools.Hand toolsareintendedfor occasionaluseandlowvolume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Handle
Emergency
Ratchet
Release
Die Retention
Screws
Ratchet Adjustment
Wheel
Moving
Jaw
Die Set
2063195-2
Nut Locator
Stationary
Jaw
Anvil (Lower)
Wire Die
Wire Crimper
(Upper Die)
Spacer
Insulation Crimper
(Upper Die)
Anvil (Lower)
Insulation Die
DIE
PART NO
IRE SIZE (mm2) INSULATION
ASSEMBLY
PART NO
.1.25-2.5 0.5-1.0 SIZE STRIP LENGTH
927779-[ ]
n
14 23
928818-[ ] ---
n
1
.
4
-
2
.
3
40
927783-[ ]
n
20 27
4
.
0
2063195-2 928876-[ ] ---
n
2
.
0
-
2
.
7
927777-[ ]
n
21 31
963885-[ ]
n
---
2
.
1
-
3
.
1
4.3
927781-[ ]
n
--- 2.7-4.1
Figure 1
1. INTRODUCTION
All dimensions on this document are in metric
units. Figures and illustrations are for
identification onl and are not drawn to scale.
SDE PEW–12 Commercial Hand Tool Assembly
2063195–1 consists of SDE PEW–12 Frame
Assembly 9–1478240–0 (Instruction Sheet 408–8851)
and die set assembly 2063195–2. See Figure 1. The
tool is used to crimp terminal numbers provided in the
table in Figure 1.
2. DESCRIPTION
The tool frame features two jaws, a handle, ratchet
adjustment wheel, and an emergency ratchet release.
The die set consists of an indenter (upper die) and an
anvil (lower die). The tool frame holds a die assembly
with two crimping chambers. See Figure 1. Die
retaining screws are used to secure the dies in the
tool frame.
The tool features a ratchet and an adjustment wheel
with a range of settings. The ratchet ensures that the
tool has completed the cycle and will not release until
the handles have been FULLY closed, unless the
emergency ratchet release is rotated to manually
release the ratchet. The adjustment wheel controls
NOTE
i
408-10224
SDE PE -12 Commercial Hand Tool Assembly 2063195-1
Rev
A2
of 5 Tyco Electronics Cor oration
the amount of handle pressure exerted on the dies
during the crimping procedure.
The dies bottom before the ratchet releases. This
feature ensures maximum tensile performance of
the crimp. DO NOT re-adjust the ratchet.
3. INSTALLATION AND REMOVAL OF DIE SET
AND LOCATOR ASSEMBLY
(Figure 1)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil so that the chamfered side
and the marked surfaces face outward, when
mounted in the moving jaw of the tool frame.
3. Insert the short die retaining screw through the
jaw and through the anvil die, and tighten the
screw just enough to hold the die in place. Do
not
tighten the screw completely at this time.
4. Place the wire crimper so that the chamfered
side and the marked surface face outward, when
mounted in the stationary jaw of the tool frame.
5. Insert the long die retaining screw through the
jaw and through the crimper die, and tighten the
screw just enough to hold the die in place. Do
not
tighten the screw completely at this time.
6. Carefully close the tool handles, making sure
that the anvil and crimper align properly. Continue
closing the tool handles until the ratchet in the tool
frame has engaged sufficiently to hold the anvil
and crimper in place, then tighten both die retaining
screws.
7. Place the nut onto the end of the long screw and
tighten the nut enough to hold the locator assembly
in place, while still allowing the locator to slide up
and down.
8. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and slide
the anvil and crimper out of the tool jaws.
The ratchet has detents with audible clicks" as
the handles are closed. The ratchet releases on
the sixth click".
4. CONTACT SUPPORT ADJUSTMENT
(Figure 2)
The contact support is preset prior to shipment,
but minor adjustment may be necessary.
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
The ratchet has detents that create audible clicks
as the tool handles are closed.
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
Figure 2
Contact
(Ty ) Stri Length
Wire Inserted
to Sto
Locator in
Wire Sto
Slot
Wire
Adjustment
Screw for
Contact
Su ort
Contact
Su ort Locator
Back of Tool
(Wire Side)
CAUTION
!
NOTE
i
NOTE
i
NOTE
i
408-10224
DE PEW-12 Commercial Hand Tool Assembly 2063195-1
3
of 5Rev
A
Tyco Electro ics Corporatio
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
5. CRIMPING PROCEDURE
T is tool is provided wit a crimp adjustment
feature. Initially, t e crimp eig t s ould be
verified as specified in Figure 3. Refer to Section
6, CRIMP HEIGHT INSPECTION, and Section 7,
CRIMP HEIGHT ADJUSTMENT, to verify crimp
eig t before using t e tool to crimp desired
contacts and wire sizes.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 2 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact through the front of the tool and into the
appropriate crimp section.
Positio Poi t o
Ce ter of Wire
Barrel Opposite
Seam
Modified A vil
A"
WIRE IZE
(MAX) mm2
CRIMP ECTION
(WIRE IZE
MARKING )
CRIMP HEIGHT
DIMEN ION A" +0.05
0.5-1.0 0.5-1.0 1.23
1.25-2.5 1.25-2.5 1.56
Figure 3
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire barrel faces the top of
the tool. Place the contact up into the nest so that
the movable locator drops into the slot in the
contact. Refer to Figure 2. Butt the front end of the
wire barrel against the movable locator.
Make sure t at bot sides of t e wire barrel are
started evenly into t e crimping section. Do NOT
attempt to crimp an improperly positioned
contact.
6. CRIMP HEIGHT IN PECTION
This inspection requires the use of a micrometer with
a modified anvil. Tyco Electronics recommends the
modified micrometer (Crimp Height Comparator
RS–1019–5LP) which may be purchased from:
ShearerIndustrialSupplyCo.
717–767–7575 or VALCO
610–691–3205
Proceed as follows:
1. Refer to Figure 1 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height listed in Figure 3. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
CRIMP HEIGHT ADJUSTMENT.
Damaged product s ould not be used. If a
damaged contact is evident, it s ould be
replaced. Contacts must not be re-terminated.
7. CRIMP HEIGHT ADJU TMENT
Although the ratchet is preset prior to shipment, it is
important to verify the crimp height using a
micrometer or caliper. General use and subsequent
wear may cause the tool to go out of adjustment. It is
recommended that crimp height be inspected, and the
ratchet be adjusted, if necessary, on a regular basis.
Refer to Figure 4, and proceed as follows:
Figure 4
Ratchet Adjustme t Wheel
Adjustme t
Screw
NOTE
i
CAUTION
!
CAUTION
!
408-10224
SDE PEW-12 Commercial Hand Tool Assem ly 2063195-1
Rev
A4
of 5 Tyco Electronics Corporation
1. If the crimp height is larger than recommended,
remove the ratchet wheel adjustment screw and
rotate the adjustment wheel counterclockwise (+)
to a higher setting. Reinstall the screw. Repeat as
required.
2. If the crimp height is smaller than
recommended, remove the ratchet wheel
adjustment screw and rotate the adjustment wheel
clockwise (–) to a lower setting. Reinstall the
screw. Repeat as required.
3. If the crimp cannot be made to conform to the
recommended crimp height, the tool or die set
must be replaced. See Section 9,
REPLACEMENT.
8. MAINTENANCE AND INSPECTION
8.1. Daily Maintenance
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or a clean, soft, lint–free
cloth. DO NOT use any objects that could damage
the dies or tool.
2. Make sure that the proper die retaining screws
are properly secured.
3. When the tool is not in use, keep the handles
closed to prevent objects from becoming lodged in
the dies. Store the tool in a clean, dry area.
4. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser.
8.2. Inspection
1. Close the tool handles until the ratchet releases,
and then allow them to quickly open freely. If they
do not open quickly and fully, the spring is
defective. See Section 9, REPLACEMENT.
9. REPLACEMENT
Order replacements through your representative, or
call 1–800–526–5142, or send a facsimile of your
purchase order to 717–986–7605, or write to:
CUSTOMER SERVICE (038–035)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105–3608
10. REVISION SUMMARY
S
Initial release of document
408-10224
SDE PEW-12 Commercial Hand Tool A embly 2063195-1
5
of 5Rev
A
Tyco Electronics Corporation
Figure 5
Pro-Crimper Han Tool 354940-1
(Instruction Sheet 408-9930) SDE PEW-12 Han Tool 9-1478240-0
(Instruction Sheet 408-8851)
SDE Bench Terminator 1490076-2
(Customer Manual 409-10052) 626 A apter 679304-1
(Instruction Sheet 408-4070)
Battery Tool (Shoul ere Die) 1725837-1, -2
(Customer Manual 409-10053) Battery Tool (Pin Die) 1213890-1, -2
(Customer Manual 409-10065)
2063195-2 Die Set can be Use in Tools Show Below
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Tyco Electronics Utensili per crimpatura
Tyco Electronics
Tyco Electronics 9-1478246-0 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III 58517 Series Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER II Manuale utente
Tyco Electronics
Tyco Electronics 90301-2 Manuale utente
Tyco Electronics
Tyco Electronics 408-10205 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics AMP 91907 Manuale utente
Tyco Electronics
Tyco Electronics PIDG Series Manuale utente
Tyco Electronics
Tyco Electronics ERGOCRIMP 2-1579021-9 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III 58564-1 Manuale utente
Tyco Electronics
Tyco Electronics 3-1579002-1 Manuale utente
Tyco Electronics
Tyco Electronics SDE PEW-12 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics 58593-1 Manuale utente
Tyco Electronics
Tyco Electronics SOLARLOK 1579004-9 Manuale utente
Tyco Electronics
Tyco Electronics 48858-1 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III 58603-1 Manuale utente
Manuali Utensili per crimpatura popolari di altre marche
Textron
Textron ESG105L Manuale utente
Emerson
Emerson Klauke ES 20RMCCFB Manuale utente
Continental Refrigerator
Continental Refrigerator PC150HD Manuale utente
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente
Emerson
Emerson Klauke ES 105CFB Manuale utente
TE Connectivity
TE Connectivity 539 726-2 Manuale utente