Tyco Electronics PRO-CRIMPER III Manuale utente
Instruction Sheet
PRO-CRIMPER* III Hand Tool Assem ly
58573-1 with Crimping Die Assem ly 408-4251
E
2005 Tyco Electronics Corporation, Harrisburg, A
All International Rights Reserved
AM and Tyco are trademarks. *Trademark
Other products, logos, and company names used are the property of their respective owners. LOC B
1
of 4
TOOLING ASSISTANCE CENTER 1-800-722-1111
RODUCT INFO 1-800-522-6752 This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
07 A R 05 Rev C
58573-2 for Spare Wire Caps
PROPER USE GUIDELINES
CumulativeTraumaDisorderscanresultfromthe prolongeduseofmanually poweredhandtools.Hand toolsareintendedfor occasionaluseandlowvolume
applications. A wide selection of powered application equipment for extended-use, production operations may be available.
Figure 1
Die Retaining
Screws
RO-CRIM ER* III
Hand Tool Frame
354940-1
Die Assembly
58573-1
Stationary Jaw
Moving Jaw
Ratchet
Adjustment
Wheel
Stationary
Handle
Moving
Handle
1. INTRODUCTION
This instruction sheet covers the use of
PRO–CRIMPER III Hand Tool 58573–1 with Crimping
Die Assembly 58573–2, which is used to apply the
standard and moisture resistant spare wire caps listed
in Figure 2. The die assembly is designed to be used
in PRO–CRIMPER III Hand Tool Frame 354940–1
(shown in Figure 1). For instructions concerning the
operation of the hand tool, refer to Instruction Sheet
408–9930, which is supplied with the tool.
Measurements are in millimeters [followed by
inch equivalents in brackets].
Reasons for reissue of this document are provided in
Section 8, REVISION SUMMARY.
2. DESCRIPTION
(Figure 1)
Each die assembly consists of an indenter die and an
anvil die. When closed, the dies form four crimping
chambers, which coincide with the four sizes of spare
wire caps. Die retaining screws are used to secure
the dies in the tool frame.
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
For Single Unstripped
Wire (Thin Copper Insert)
With or Without Moisture-
Resistant Inhibitor
WIRE
INSUL
SPARE WIRE CAP No's CAP TOOL
COLOR
INSUL
.
DIA.
RANGE STANDARD MOISTURE
RESISTANT
COLOR
CODE
COLOR
CODE
DOT
1.22 - 1.91
[.048 - .075] 324484 324693 WHITE WHITE
2.03 - 2.92
[.080 - .115] 324485 324694 RED RED
3.05 - 3.68
[.120 - .145] 324486 324695 BLUE BLUE
3.81 - 5.33
[.150 - .210] 324487 324696 YELLOW YELLOW
Figure 2
NOTE
408-4251
PRO-CRIMPER III Hand Too Assemb y 58573-1
R v
C2
of 4
Figure 3
Tool Jaws
(R f)
Di Ass mbly
PRO-CRIMPER II
Hand Tool Fram
Ass mbly 354940-1
Di
R taining
Scr ws
Ind nt r
Anvil
3. DIE INSTALLATION
1. Close the tool handles until the ratchet releases,
then allow the handles to open fully.
2. Insert the dies into the tool jaws as shown in
Figure 3, and align the die retaining holes in each
die with the associated holes in the tool.
3. Thread, but do not tighten, the die retaining
screws into the holes.
4. Carefully close the tool handles, making sure
that the dies align properly.
5. Tighten the die retaining screws.
4. CRIMPING PROCEDURE
1. Refer to Figure 2, and select a cap of the
correct size for the insulation diameter of the wire
being used.
2. Identify the color code of the cap, and insert the
cap into the crimping chamber with the same color
code. Be sure that the cap is fully inserted.
3. Begin closing the tool handles until the cap is
held firmly in place. Do NOT deform the cap.
4. Insert the unstripped wire completely into the
cap.
When bottoming the wire in a moisture-resistant
cap, greater insertion force must be exerted on
the wire to displace the inhibitor present in the
cap.
5. Close the tool handles until the ratchet releases.
6. Allow the tool handles to open FULLY and
remove the crimped cap from the crimping
chamber by turning the cap and wire 1/4 turn while
pulling lightly on the wire.
Damaged products may not be used. If a
damaged product is evident, it must be replaced.
5. CRIMP INSPECTION
(Figur 4)
Inspect the crimped spare wire cap. The crimp should
be near the center of the insert in the cap, and the
wire should be bottomed in the cap.
Double check that the correct cap was used for the
wire’s insulation diameter, and make sure that the
correct crimping chamber was used.
If the cap fails inspection, remove the cap by cutting
the wire, then apply a new cap to the wire by carefully
following the above procedure.
Figure 4
Wir bottom d in cap.
1Crimp n ar c nt r of ins rt. (Cap was fully bottom d in
di closur .)
2Corr ct wir insulation diam t r for cap
b ing us d.
3
4Cap insulation color match s di closur color dot cod .
1
3
4
2
NOTE
CAUTION
408-4251
PRO-CRIMPER III Hand Tool Assembly 58573-1
3
of 4Rev
C
DC
B
A
HAND TOOL AND DIE
ASSEMBLY
DIE OPENING +0.10 .004]
ASSEMBLY
PART NUMBERS AB C D
58573-1
58573-2 1.83 [.072] 2.26 [.089] 2.95 [.116] 3.61 [.142]
Figure 5
6. MAINTENANCE AND INSPECTION
6.1. Maintenance
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or a clean, soft, lint–free
cloth. Do NOT use any objects that could damage
the dies or tool.
2. Make sure that the proper die retaining screws
are properly secured.
3. When the dies are not in use, store them in a
clean, dry area. When the tool is not in use, store it
with the handles closed to prevent objects from
being lodged within the jaws.
6.2. Inspection
1. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser.
2. Make certain that all die retaining screws and
die components are properly secured.
3. Inspect the crimping surfaces for flattened,
chipped, worn, or cracked areas. If damage is
evident, the dies must be replaced. Refer to
Section 7, REPLACEMENT.
6.3. Measuring Die Opening
The die assembly will perform correctly as long as:
(1) the product specified is correct for the application,
(2) the specific die assembly is used, (3) the die
assembly has been measured to ensure that the
openings are correct, and (4) the die assembly
bottoms.
Figure 5 provides information on die opening sizes.
6.4. Ratchet Adjustment
(Figure 6)
The tool frame assembly ratchet mechanism features
an adjustment wheel with numbered settings. If the
crimp height is not acceptable, adjust the ratchet as
follows:
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the opposite side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher–numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower–numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the crimp height is acceptable, secure the
lockscrew. If the dimension is unacceptable,
remove lockscrew and continue to adjust the
ratchet, and again measure a sample crimp.
408-4251
PRO-CRIMPER III Hand Too Assemb y 58573-1
Rev
C4
of 4
Figure 6
Screwdriver
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
7. REPLACEMENT
Order replacements through your Tyco Electronics
Representative, or call 1–800–526–5142, or send a
facsimile of your purchase order to 1–717–986–7605,
or write to:
CUSTOMER SERVICE (38–35)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105–3608
8. REVISION SUMMARY
Since the previous release of this document, the
following changes have been made:
Per EC 0990–0465–05:
S
Updated document to corporate requirements
S
Added die set 58573–2 to title, Introduction,
and table in Figure 5
S
Changed lockscrew in Figures 1, 2, and 6
S
Changed PRO–CRIMPER II to
PRO–CRIMPER III in all instances
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Tyco Electronics Utensili per crimpatura
Tyco Electronics
Tyco Electronics 90654-1 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics AUTOPRESS C120 Nota di rilascio
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics 1901820-1 Manuale utente
Tyco Electronics
Tyco Electronics CERTI-CRIMP II Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics 1490748-1 Manuale utente
Tyco Electronics
Tyco Electronics 2-1579004-9 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III 58603-1 Manuale utente
Tyco Electronics
Tyco Electronics 1752787-1 Manuale utente
Tyco Electronics
Tyco Electronics 58649-1 Manuale utente
Tyco Electronics
Tyco Electronics PIDG STRATO-THERM Manuale utente
Tyco Electronics
Tyco Electronics 2063811-1 Manuale utente
Tyco Electronics
Tyco Electronics SDE-SA 2063526 Series Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III 58564-1 Manuale utente
Tyco Electronics
Tyco Electronics 90035-3 Manuale utente
Tyco Electronics
Tyco Electronics ERGOCRIMP 2-1579021-9 Manuale utente
Manuali Utensili per crimpatura popolari di altre marche
Textron
Textron ESG105L Manuale utente
Emerson
Emerson Klauke ES 20RMCCFB Manuale utente
Continental Refrigerator
Continental Refrigerator PC150HD Manuale utente
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente
Emerson
Emerson Klauke ES 105CFB Manuale utente
TE Connectivity
TE Connectivity 539 726-2 Manuale utente