Tyco Electronics PRO-CRIMPER III Manuale utente
Instruction Sheet
PRO-CRIMPER* III Hand ool Assembly 408-9830
L C B
1
of 3
E
2007 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. ther products, logos, and company names used are the property of their respective owners.
T LING ASSISTANCE CENTER 1-800-722-1111
PR DUCT INF RMATI N 1-800-522-6752 This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
08 AUG 07 Rev E
58499-1 with Die Assembly 58483-1
PROPER USE GUIDELINES
CumulativeTrauma Disorderscanresultfromtheprolongeduseofmanuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
The PR -CRIMPER III Hand Tool is a Commercial" grade tool and is
designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate Application Specification (114-series), but may not comply
with other feature parameters of the specification. A variety of tools are offered
to satisfy your performance requirements. For additional information, contact
the Tooling Assistance Center at 1-800-722-1111.
Die Assembly
Moving Jaw
Ratchet Adjustment
Wheel
Moving Handle
Stationary Handle
PR -CRIMPER III Hand Tool
Frame 354940-1 (See Instruction
Sheet 408-9930)
Pivot Pin
Back of Tool
(Wire Side)
Stationary
Jaw
DIE ASSEMBLY PRODUC
FAMILY FLEXIBLE COAXIAL
CABLE SIZE (RG/U)
DIE ASSEMBLY
CRIMPING CHAMBER
MARKING
178, 196 .105 (A)
58483-1 SMB Straight Cable
Plug Connectors
174, 179, 187, 188, 316 .128 (B)
Plug Connectors
174, 188, 316 (All Double Braid) .151 (C)
Figure 1
1. IN RODUC ION
PRO–CRIMPER III Hand Tool Assembly 58499–1
consists of PRO–CRIMPER III Hand Tool Frame
354940–1 and Die Assembly 58483–1. The tool
assembly is used to crimp the ferrule of the
connectors listed in Figure 1. In this use, the die
assembly does not provide for crimping of the center
contact.
Read these instructions thoroughly before using the
tool assembly.
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures are
not drawn to scale.
For additional information on the hand tool frame,
refer to 408–9930. Refer to the applicable connector
instruction sheet for assembly of the connector.
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
NO E
i
Downloaded from Arrow.com.
408-9830
PRO-CRIMPER III Hand Tool Assembly 58499-1 with Die Assembly 58483-1
Rev
E2
of 3 Tyco Electro ics Corporatio
2. DESCRIPTION
(Figure 1)
The tool frame features a stationary jaw and handle, a
moving jaw, a moving handle, and an adjustable
ratchet that ensures full crimping. The tool frame
holds the die assembly.
The die assembly consists of an indenter (stationary
die) and an anvil (moving die). When closed, the dies
form three crimping chambers. Each die is held in the
hand tool frame by a single screw.
3. INSTALLATION AND REMOVAL OF
DIE ASSEMBL
(Figure 2)
1. Close the tool handles until the ratchet releases,
then allow the handles to open fully.
2. Insert the dies into the tool jaws as shown in
Figure 2, and align the retaining holes in each die
with the associated hole in the tool.
Figure 2
Tool Frame
Jaws
Die Retai i g
Screws
A vil
I de ter
3. Thread, but do not tighten, the die retaining
screws into the holes.
4. Carefully close the tool handles, making sure
that the dies align properly.
5. Tighten the die retaining screws with the
appropriate hex wrench.
6. To disassemble, close the tool handles until the
ratchet releases, remove the two die retaining
screws, and slide the dies out of the tool jaws.
4. CRIMPING PROCEDURE
(Ferrule O ly)
Make sure that the center contact is properly crimped
and assembled onto the connector as described in
applicable connector instruction sheet. Then proceed
as follows:
1. Slide the ferrule over the cable braid until it is
positioned against the shoulder of the plug body.
2. Close the tool handles until the ratchet releases,
then allow the handles to open FULLY.
3. Place the ferrule in the appropriate crimping
chamber on the anvil die so that the shoulder of
the plug body is close to the edge of the die. Refer
to Figure 3.
Refer to Figure 1 for the appropriate crimping
chamber.
Figure 3
Shoulder of Plug
Body Close to
Edge of Die
Crimpi g
Chamber
(Ref)
4. While holding the assembly, close the tool
handles until the dies hold the ferrule in place.
5. Carefully close the tool handles until the ratchet
releases, then allow the handles to open FULLY.
6. Remove the ferrule from the dies.
7. Inspect the crimped ferrule according to
applicable connector instruction sheet. If
necessary, adjust the ratchet as described in
Section 5.
5. RATCHET ADJUSTMENT
(Figure 4)
The tool ratchet mechanism features an adjustment
wheel with numbered settings. The adjustment wheel
controls the amount of handle pressure exerted on
the jaws during crimping. If the crimp is not
acceptable, adjust the ratchet as follows:
1. Remove the lockscrew from the ratchet
adjustment wheel.
NOTE
i
Downloaded from Arrow.com.Downloaded from Arrow.com.
408-9830
PRO-CRIMPER III Hand Tool Assembly 58499-1 with Die Assembly 58483-1
3
of 3Rev
E
Tyco Electro ics Corporatio
Screwdriver
Ratchet
Adjustme t
Wheel
Lockscrew
Figure 4
2. With a screwdriver, adjust the ratchet wheel
from the front of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel
counterclockwise
to a higher–numbered
setting. If a looser crimp is required, rotate the
adjustment wheel
clockwise
to a lower–numbered
setting.
4. Re–assemble the lockscrew.
5. Make a sample crimp. If the crimp is acceptable,
the adjustment setting is correct. If the crimp is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
6. MAINTENANCE AND INSPECTION
6.1. Maintenance
Ensure that the tool frame and dies are clean by
wiping them with a clean, soft cloth. Remove any
debris with a clean, soft brush. Do not use objects
that could damage any components. When not in use,
keep tool handles closed to prevent objects from
becoming lodged in the dies, and store in a clean, dry
area.
6.2. isual Inspection
Inspection of the dies should be made on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimping sections for flattened,
chipped, worn, or broken areas. If damage or
abnormal wear is evident, the dies must be replaced.
Refer to Section 7, REPLACEMENT.
6.3. Measuring Die Opening
Figure 5 provides dimensions for the die openings.
C
A
B
DIE OPENING DIMENSION +0.10 [+.004]
A B C
2.667 [.105] 3.251 [.128] 3.835 [.151]
Figure 5
7. REPLACEMENT
Customer–replaceable parts are shown in Figure 1.
Available separately, Repair Kit 679221–1 includes a
replacement nut and a variety of pins, rings, screws,
and springs. If the dies are damaged or worn
excessively, they must be replaced. Order the repair
kit and replaceable parts through your representative,
or call 1–800–526–5142, or send a facsimile of your
purchase order to 717–986–7605, or write to:
CUSTOMER SERVICE (038–035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105–3608
8. RE ISION SUMMARY
Revisions to this instruction sheet include:
S
Updated document to corporate requirements
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Tyco Electronics Utensili per crimpatura
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics 90430-1 Manuale utente
Tyco Electronics
Tyco Electronics 408-10205 Manuale utente
Tyco Electronics
Tyco Electronics PIDG STRATO-THERM Manuale utente
Tyco Electronics
Tyco Electronics 1752787-1 Manuale utente
Tyco Electronics
Tyco Electronics PRO- CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics 90301-2 Manuale utente
Tyco Electronics
Tyco Electronics 69156-1 Manuale utente
Tyco Electronics
Tyco Electronics 2063195-1 Manuale utente
Tyco Electronics
Tyco Electronics 45449 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics ERGOCRIMP 3-1579001-5 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics SIMEL Autocoup CC040 Cof. + charg. Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuale utente
Tyco Electronics
Tyco Electronics 1213850-1 Manuale utente
Tyco Electronics
Tyco Electronics 1-1579001-2 Manuale utente
Tyco Electronics
Tyco Electronics 696675-1 Manuale utente
Tyco Electronics
Tyco Electronics PRO-CRIMPER III 58603-1 Manuale utente
Manuali Utensili per crimpatura popolari di altre marche
Textron
Textron ESG105L Manuale utente
Emerson
Emerson Klauke ES 20RMCCFB Manuale utente
Continental Refrigerator
Continental Refrigerator PC150HD Manuale utente
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente
Emerson
Emerson Klauke ES 105CFB Manuale utente
TE Connectivity
TE Connectivity 539 726-2 Manuale utente