Tylo SENSE PLUS Manuale utente
1303
ENGLISH
INSTALLATION GUIDE
SENSE PLUS /MPE
29005150 -ENG
X
Keep this user guide!
In the event of any problems, please contact the retailer where
you purchased the equipment.
© This publication may not be reproduced, in part or in whole,
without the written permission of Tylö. Tylö reserves the right to
make changes in materials, construction and design.
TABLE OF CONTENTS
Before installation ..........................................................1
Parts .......................................................................................1
Installation requirements ........................................................ 1
Installation tools ..................................................................... 1
Planning installation ............................................................... 2
Installation ...................................................................... 4
Sauna heater installation ....................................................... 4
Connection/wiring diagram ........................................... 7
Checking installation ..................................................... 8
1
BEFORE INSTALLATION
Parts
Check that the following parts are included in the packaging:
32
1
4
7
6
910 11
8
5
Figure 1: Sauna heater parts
1. Sauna heater
2. Herb bowl/air humidifier
3. Brackets x 4
4. Sensor/temperature cut-out C-P, cable length 4 m
5. Warning sticker in ten languages
6. 3 mm Allen key
7. Lock screws M5x6 x
8. Bracket screws x 8
9. Connectors x 3
10. Screws RXS/A2 PHIL B6x25 x 2
11. Clips TC (5-7) x 10
Contact your dealer if anything is missing.
The following control panels are compatible with Sense Plus:
CC10, CC50, CC300, EC50 and h1.
Control panel CC10 is supplied with Sense MPE.
Cable between heater and control panel must be: shielded cable
(LiYCY 8X0. 25 mm²).
Installation requirements
For detailed instructions concerning sauna construction/ventila-
tion etc., go to: http://www.tylö.se/byggabastu and download this
document: "Building a sauna.pdf".
To ensure safe use of the heater, check that the following criteria
are met:
• The sauna cabin should meet the requirements for ceiling
height and dimensions according to: "Building a sauna.pdf".
• The sauna cabin should meet the requirements for insulation
and materials according to: "Building a sauna.pdf".
• Cable (EKK) or electrical ducting for connecting the heater
must be run on the outside of the heat insulation.
• Cable installation must be correctly performed (see The sec-
tion called Connection/wiring diagram, Page 7).
• Fuse size (A) and power cable size (mm²) must be suitable
for the heater (see The section called Connection/wiring dia-
gram, Page 7).
• The sauna ventilation must comply with the instructions in this
manual (see The section called Positioning the inlet vent,
Page 3, The section called Positioning the outlet vent,
Page 3).
• The position of the sauna heater, control panel and sensors
must comply with the instructions in this manual.
• The heater output (kW) must be suitable for the sauna volume
(m³) (see Table 1, Page 1). The minimum and maximum
volumes must not be exceeded.
NOTE! A brick wall without heat insulation increases
the warm-up time. Each square metre of plastered
ceiling or wall surface equals an additional 1.2–2 m³
of sauna volume.
Table 1: Output and sauna volume
Output kW Sauna volume min./max. m³
6.6 4-8
8 6-12
!
DANGER! Incorrect ventilation or heater positioning
can lead to the wooden panels drying out, posing a
fire risk in certain circumstances.
!
DANGER! Insufficient insulation of the sauna cabin
can pose a fire risk.
!
DANGER! Use of the wrong materials in the cabin,
such as chipboard, plasterboard etc., can pose a fire
risk.
!
DANGER! The heater must be connected by a qual-
ified electrician according to the applicable regula-
tions.
Installation tools
The following tools and materials are needed for installation and
connection:
• spirit level,
• adjustable spanner,
• electric drill,
• screwdriver.
2
Planning installation
Before starting to install your sauna heater:
• Plan where to position the sauna heater (see The section
called Positioning the heater - normal installation, Page
2).
• Plan where to position the control panel (see control panel in-
structions for correct positioning).
• Plan where to position the sensor (see Figure 3, Page 2
and Figure 5, Page 3).
• Position the inlet vent (see The section called Positioning the
inlet vent, Page 3).
• Position the outlet vent (see The section called Positioning
the outlet vent, Page 3).
1
2
34
Figure 2: Schematic diagram of installation
1. Sauna heater
2. Control panel
3. Sensor
4. External on/off switch (option)
Positioning the heater - normal installation
!
DANGER! More than one heater can be installed in
the same sauna cabin.
Position the sauna heater:
• on the same wall as the door (or the side wall if very close to
the door wall). The heater can also be positioned in a recess
(see Figure 5, Page 3).
• at a safe distance from the floor, side walls and interior fittings
(see Figure 3, Page 2).
Position the sensor according to the diagram (see Figure 3, Page
2).
16
9
8
10
7
5
2
4
3
Figure 3: Positioning the heater - normal installation
1. Minimum distance from side wall: 110 mm
2. Sensor position: 200 mm from heater
3. Sensor
4. Sensor position: 40 mm from ceiling, regardless of ceiling
height
5. Minimum distance from ceiling: 1030 mm
6. Minimum distance from interior fittings: 100 mm
7. Minimum ceiling height: 1900 mm
8. Minimum distance: 20 mm
9. Minimum distance from interior fittings: 30 mm
10. Distance from floor: 100-270 mm (with legs: 100 mm)
If the wall that the sensor is to be installed on is made of highly
heat insulating material (e.g. concrete, brick) or of toughened
glass, the sensor can be installed directly above the heater
(above the centreline of the heater as seen from the front and
side see Figure 4, Page 2).
1
Figure 4: Sensor installation on ceiling on centreline of heater as
seen from the front and side
1. 200 mm
Positioning the heater - recess installation
To position the sauna heater in a recess:
1. Position the heater at a safe distance from the floor, side walls
and interior fittings (see Figure 5, Page 3).
3
2. Position the sensor according to the diagram (see Figure 5,
Page 3).
7
10
9
11
4
5
2
3
1 1 8
6
Figure 5: Positioning the heater - recess installation
1. Minimum distance from side wall: 200 mm
2. Sensor position: 200 mm from heater
3. Sensor
4. Max. 1000 mm
5. Sensor position: 40 mm from ceiling, regardless of ceiling
height
6. Minimum distance from ceiling: 1030 mm
7. Minimum distance from interior fittings: 100 mm
8. Minimum ceiling height: 1900 mm
9. Minimum distance: 20 mm
10. Minimum distance from interior fittings: 30 mm
11. Distance from floor: 100-270 mm (with legs: 100 mm)
Positioning the inlet vent
Install the inlet vent straight through the wall under the centreline
of the heater. Vent size for a family sauna approx. 125 cm².
The air circulation from the door must concord with the hot air cir-
culation from the heater.
1 2
3 4
Figure 6: Positioning the inlet and outlet vents
1. Inlet vent position.
2. Outlet vent position through the sauna wall.
3. Outlet vent position through the cavity.
4. Outlet vent position via duct.
Positioning the outlet vent
!
DANGER! The outlet vent must not lead outdoors.
This could cause the ventilation direction to be re-
versed, which may negatively affect the heater tem-
perature cut-out.
!
DANGER! Any gap above the sauna ceiling should
not be sealed without leaving at least one vent hole
on the same wall as the sauna door.
Position the outlet vent
• at the maximum possible distance from the inlet vent, e.g. di-
agonally (see Figure 6, Page 3).
• high on the wall or in the ceiling (see Figure 6, Page 3).
• so that it vents into the space the door and inlet vent open in-
to.
The outlet vent must have the same area as the inlet vent.
Ensure that the outlet vent is open.
Mechanical ventilation is not recommended due to the risk of poor
air exchange, which can negatively affect the heater temperature
cut-out.
4
INSTALLATION
Sauna heater installation
It is easiest to prepare for installation with the heater lying down.
To install the heater:
1. Lay the heater down front upwards.
2. Slacken the screws and open the cover (see Figure 7, Page
4).
Figure 7: Opening/closing the cover
3.
!
WARNING! Always check that the heater is con-
nected to the correct main/phase voltage.
Connect the heater using standard wiring (Fk or EKK) ap-
proved for fixed installation.
Any single wires (Fk) must be protected in electrical conduits
(VP) to the heater.
Connect the electrical cable (1) to terminal (2) (see Figure
8, Page 4) according to wiring diagram (see The section
called Connection/wiring diagram, Page 7).
3
2
46 75
18
Figure 8: Circuit board
1. Electrical cable
2. Terminal for connection of electrical cable
3. Control panel cable
4. Terminal for connection of control panel
5. Sensor cable
6. Terminal for connection of control panel and sensor
7. Light cable (if relevant)
8. Terminal for connection of light (if relevant)
4. Connect the control panel cable (3) to terminals (4 and 6) (see
Figure 8, Page 4) according to the wiring diagram (see
The section called Connection/wiring diagram, Page 7).
5. Connect the sensor cable (5) to terminal (6) (see The section
called Connection/wiring diagram, Page 7) according to
the wiring diagram (see The section called Connection/wir-
ing diagram, Page 7).
6. Connect light cable (if relevant) (7) see Figure 8, Page 4
to terminal (8) according to the wiring diagramFigure 16,
Page 7.
7. Close the cover and tighten the screws (see Figure 7, Page
4).
5
8. Use the drill template to mark the heater's position (see Fig-
ure 9, Page 5). The drill templates will position the heat-
er 150 mm from the floor. (This step is not required if the heat-
er is to stand on the floor. See separate instructions for heater
feet (option).)
2
1
3
4
Figure 9: Drill template
1. 298 mm
2. 308 mm
3. 340 mm
4. 48 mm
9. Attach the four brackets to the wall following the template
markings. Attach the two lower brackets with their screw hole
downwards so that the hole is hidden. Only the two upper
brackets need locking with the lock screws (see Figure 10,
Page 5).
Figure 10: Bracket and screws
10. Install the sensor on the wall see Figure 11, Page 5.
Tighten the screws carefully to avoid breaking the circuit
board.
Figure 11: Installing the sensor
11. Attach the herb bowl/air humidifier (see Figure 12, Page
5).
Figure 12: Installing the fragrance holder/air humidifier
6
12. Insert the lock screws (M5x6 mm) into the screw holes on the
brackets (see Figure 13, Page 6).
Figure 13: Insert the lock screw into the screw hole
13. Hang the heater on the brackets by sliding it straight in to-
wards the wall (see Figure 14, Page 6). It may be ne-
cessary to slacken the bracket screws slightly. Tighten them
again after the heater has been hung up.
Figure 14: Sliding the heater on
14. Tighten both lock screws using an Allen key. (see Figure 15,
Page 6).
Figure 15: Tightening the lock screws
Unusual voltages/numbers of phases
Before connecting to voltages or numbers of phases not listed in
the wiring diagram Figure 16, Page 7, contact Tylö Customer
Service.
7
CONNECTION/WIRING DIAGRAM
Output kW Voltage Amperage Wiring area mm²
6.6 400V 3N~ 10 1.5
8 400V 3N~ 12 2.5
1
1
77
3
2
3
5
4
6
5
Figure 16: Wiring diagram
1. Heater
2. Terminal for connection of electrical cable
3. Control panel
4. Terminal for connection of control panels CC10, CC50, CC300, EC50 and h1
5. Sensor
6. Terminal for connection of control panel and sensor
7. Light/terminal for connection of light
8
CHECKING INSTALLATION
To check the installation:
1. Switch heater on (see User Guide).
2. Check that the control panel lights up .
3. Start the heater (see User Guide).
4. Check that all three tubular elements start to heat up (go red).
Altri manuali per SENSE PLUS
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Tylo Stufa
Tylo
Tylo Sense Combi-U7 Manuale utente
Tylo
Tylo SENSE PLUS/MPE Manuale utente
Tylo
Tylo Expression Manuale utente
Tylo
Tylo SENSE SPORT Manuale utente
Tylo
Tylo H2 Manuale utente
Tylo
Tylo SENSE SPORT COMBI 4 Manuale utente
Tylo
Tylo COMPACT 2/4 Manuale utente
Tylo
Tylo CROWN ELITE Manuale utente
Tylo
Tylo Steam Outlet Commercial Manuale utente
Tylo
Tylo SENSE SPORT 2/4 Manuale utente
Tylo
Tylo AIR Manuale utente
Tylo
Tylo SU 2/4 Manuale utente
Tylo
Tylo Sense Pure Manuale utente
Tylo
Tylo SENSE COMBI Manuale utente
Tylo
Tylo SENSE COMBI Pure Manuale utente
Tylo
Tylo SENSE COMMERCIAL Manuale utente
Tylo
Tylo Sense Combi USA Pure Manuale operativo
Tylo
Tylo MPE Series Manuale utente
Tylo
Tylo Expression Combi Manuale utente
Tylo
Tylo SENSE SPORT Manuale utente
Manuali Stufa popolari di altre marche
Empire Heating Systems
Empire Heating Systems WCC65 Manuale utente
Wetekom
Wetekom 92 86 43 Manuale utente
Desa
Desa SPC170-F Manuale utente
Watlow
Watlow Watrod Electric Tubular Heaters Manuale utente
Haverland
Haverland ECO-DRY GPS Series Manuale elenco delle parti
Stelpro
Stelpro ASILVC2060 Series Manuale utente