Tylo Prime+ 1811 Manuale utente

3 person infrared sauna

Prime+ 1811

User Manual

Note: The cabin must be installed on a flat, level surface.

Precautions to be taken before commissioning

Pre-assembly information

Electrical requirements

Cabin construction/ assembly

Junction box connections

Main junction box connections

Power connections on the ceiling

Control panel instructions

Lighting: Internal/ external/ colour therapy

Maintenance & technical support

Wiring diagram

121210

Page 1

Precautions to be taken before commissioning Warning (space configuration and use):

•Correct electrical earthing is required

•Electrical sockets are not permitted in the sauna.

•Do not allow heating elements to come into contact with water.

•Do not fit a lock or bolt on the door.

•Do not block the ventilation holes.

•Children must always be supervised in the sauna.

•Clean the sauna with a damp cloth.

•Cleaning the sauna with steam cleaners, high pressure cleaners or spraying with water is not permitted.

Electrical warning – “Do not insert the sauna power cable into a socket before assembly is complete.”

Warning (human restrictions):

•Being exposed to high temperatures for a long time may lead to hyperthermia (body temperature is several

degrees above 37° Celsius)

•Hyperthermia symptoms include: dizziness, lethargy, grogginess and feeling faint. Effects of hyperthermia:

oFailure to realise that you have to leave the infrared sauna.

oDamage to the foetus in pregnant women.

oBeing physically unable to leave the sauna.

oLoss of consciousness

•Warning – the consumption of alcohol or drugs increases the risk of fatal hyperthermia.

•If you have health problems or are ill, consult your doctor before using the sauna.

•Stop using it immediately if you feel restless, if you start shaking, if you have a headache or feel sick

or nauseous.

•People who suffer from hyperthermia or cardiovascular diseases should seek medical advice before using

the infrared sauna.

•Do not use a sauna if you have drunk alcohol or taken tranquillisers or if you suffer from pain in the heat.

•Using the infrared sauna is not advisable if you have been exposed to UV radiation (a solarium or been

sunbathing) in the last 24 hours.

•Should you notice unusual skin changes after using the infrared sauna e.g. persistent erythema (reddening

of the skin for more than one day) or a reticular change in colour, you should stop using it and seek medical

advice.

Warning (fire risk):

•Do not use the sauna to dry clothing, bathing costumes etc.

•Do not hang towels or other objects on or in front of the infrared heat radiator.

•Never operate the infrared sauna with a damaged cable or a damaged socket.

Pre-assembly information:

a. Two (2) adults are required to assemble and install the sauna.

b. Assembly tools: Phillips screwdriver

c. The boxes are labelled in order of assembly.

d. Note: The glass for assembling the front wall panel is heavy and fragile.

Box 1: Floor, ceiling, bench valance, bench, fan component and manual

Pack of 10 Phillips screws for the junction box covers

Door handle set

Box 2: Back and front panels

Box 3: Left and right panels

Electrical requirements: The infrared sauna must have a 230 volt connection.

Page 2

How to construct the sauna:

Note – there are 11 power connections in all and several low voltage connections.

(7) are in the cabin: (back, left and right) wall panels, bench valance, bench valance fan,

bench and main power connection.

There are additional power connections on the top outer face of the ceiling.

(1) Mains connection cable for the cabin. Do NOT insert the main electrical connection

cable for the sauna into the socket before all the assembly steps have been

completed correctly.

------------------------------------------------------------------------------------------------------------------------------------------------

There are (5) power connection/ junction boxes that are labelled accordingly and must be connected after

assembling each section.

Back panel Left Right Bench valance Bench

B1 to B1 L1 to L1 R1 to R1 S3 to S3 S1 to S1

B2 to B2

These (5) power plugs are connected easily by simply inserting the white plug of the white junction

box cover into the correct plug-in connection (3) in the junction box.

Example below: L1 to L1 (left wall panel power connection) (left wall panel junction box)

Fitting the junction box covers: After the junction box has been connected securely fix the junction

box cover with a Phillips screwdriver and 2 Phillips screws from Box 1.

Floor panel (Box 1): Put the floor panel on a level surface 8-16 cm from the wall panel and no more

than 152 cm away from a 230V socket.

Page 3

Position the floor panel in such a way that the ceramic tiles/ IR floor heating point towards the front

of the sauna.

Note: Put the ceiling, bench valance and bench aside until the corresponding steps.

Rear wall panel (Box 2):

•Place the rear wall panel part into the rear slot on the floor panel.

•Attach the second back panel section to the first back panel section (see picture below).

•The back panel part must be held upright until the right panel is fitted.

•Connect the electricity supply to the B-1 junction box.

•Fix the cover of the B-1 junction box with 2 Phillips screws.

Note – Put the front panel aside until the “Front panel” section.

Page 4

Right wall panel (Box 3):

•Place the right panel in the right hand slot on the floor panel.

•Attach the back wall panel to the right wall panel by lifting the right panel and pushing

it into the retaining bracket on the back panel.

•Connect the R-1 electrical supply to the R-1 junction box.

•Fix the cover of the R-1 junction box with 2 Phillips screws.

Left wall panel (Box 3):

•Place the left panel in the left hand slot on the floor panel.

•Attach the back panel to the left panel by lifting the left panel and pushing

it into the retaining bracket on the back panel.

•Connect the L-1 electrical supply to the L-1 junction box.

•Fix the cover of the L-1 junction box with 2 Phillips screws.

Page 5

Bench valance (Box 1):

•Insert the bench valance between the right and left wall panel sections.

•Connect the S-3 electrical supply to the S-3 junction box.

•Fix the cover of the S-3 junction box with 2 Phillips screws.

Slide the fan component (Box 1) into

the support on the bench valance.

Connect the white connection on the black

junction box to the white connection on the fan.

Black main junction box: (2) connections

Locate the black main junction box that is fixed to the internal floor of the sauna.

1 Insert the 24 pin, multicoloured cable plug into the left hand side of the main junction box.

See point 3 -

Input/output

2 The ON/ OFF switch is on the right hand side of the main junction box.

Set the switch as shown above to the ON (EIN) position.

3 Connect the loudspeaker input and output.

Note – Do NOT insert the 230 volt alternating current cable into the socket yet.

Page 6

Bench (Box 1):

•Push the bench seat downwards into the back panel with the junction box pointing towards

you.

•Tilt the bench against the back panel as shown below.

•Connect the S-1 electrical connector to the S-1 junction box.

•Fix the cover of the S-1 junction box with 2 Phillips screws.

•Connect the bench valance strip lights to the strip light connection in the connector (Note:

two connections may come out of the floor with some models. You only need to connect

one with this model.)

•Lay the bench down and push it into the right place.

Front wall panel (Box 2):

•Insert the front left glass section into the slot provided.

•(Note: The seal should be in the middle and on the inside

of the sauna.)

•Two adults are required to push the right fixed section

into the front right hand slot.

•The person who is holding the door will have to help

fit the section into the floor and side panel.

•When the section is fixed securely to the floor and the side

panel you are ready for the ceiling section.

Note: All wall panel parts are now connected but not secured.

Note: If additional helpers are not available to hold the glass sections

while two people fix the ceiling section, fix the whole front with

adhesive tape.

Page 7

Ceiling (Box 1):

•Lift the ceiling up and place it carefully on the four (4) wall panels as shown below.

•Note: Ensure that the electrical connections are placed through the ceiling and are not disconnected

when you put the ceiling into position slowly.

•Tip: To make it easier to pull cables through the ceiling slot, you can take small styropor blocks and

put them in several places between the ceiling and the wall panels so that the ceiling stays put. When

the cables have been pulled through, remove the styropor blocks and lower the ceiling onto the wall

panels.

•Using a step ladder, open the flaps in the ceiling and turn the wooden support 90º. This fixes

the ceiling securely onto the wall panels and ensures that the door panel cannot fall out.

A dipole radio antenna is supplied with your infrared sauna for better

FM reception.

You will find the dipole antenna in the bag in the installation manual.

1. Take the dipole antenna (black wires) out of the bag in the installation

manual.

2. Open the cover on the top of the ceiling above the touch screen.

3. Connect the dipole antenna to the wire marked 7

4. Spread the wire out and pull it apart to improve FM radio reception.

Ceiling to the rear wall panel: (2) connections:

Lift the door panel on the top left of the rear external

face of the ceiling. You will see 4 connections

labelled 1 – 4.

Fix each ceiling connection 1 – 4 to the

corresponding number.

Ensure that they are connected securely to each

other. After connecting close the ceiling flap.

Connection between the ceiling and front wall panel:

•Lift the door on the top of the ceiling.

You will see four connections.

Note: Connect white to black

on the 2 black and white cables

•Connect the other 2 connections matching the colours.

•Numbered 5, 6, 7 & 8. Connect numbers 5 – 8 to 5 – 8.

•Close the front ceiling flap.

Page 8

Door handles:

Inside Outside

Your infrared sauna is now ready for use.

------------------------------------------------------------------------------------------------------------------------------------------------

Page 9

Control panel instructions:

Main current: Press POWER to turn the sauna ON (AN) or OFF (AUS). If a red light comes

on the sauna is ON. If it is white the sauna is OFF.

Timer functions: Press and hold down or in order to set the running time. You can

also run your finger up or down the timer to set it.

Timer 2: Use this function with a pre-setting of up to 24 hours to set the sauna to come on later.

Temperature functions:

1. Press to switch between Cand F. C or F will light up to show the required units.

2. Press and hold or to set the required temperature.

Pressing once will increase or reduce the setting in one degree intervals. You can also run your finger

over the temperature bar.

The central temperature display shows the actual sauna temperature.

3. Press to set the bench/ leg/ floor heat to ON or OFF. Red waves can be seen in heating mode

and white ones in OFF mode.

Light functions:

1. Press Inside light to switch it ON or OFF.

2. Note: Outside light ON or OFF will not work with S series models.

Colour therapy functions:

Press the colour therapy light in order to activate coloured light or a colour sequence. This sequence

is shown in detail below:

1. Press – RED

2. Press – RED-GREEN

3. Press – GREEN

Page 10

Altri manuali per Prime+ 1811

Indice

Lingue:

Altri manuali Tylo Sauna

Tylo

Tylo Prime+ 1814 Manuale utente