U-Line H-1495 Manuale utente
PAGE 1 OF 24 0721 IH-1495
1-800-295-5510
uline.com
MOBILE
WORKSTATION
H-1495, H-1496
H-1497, H-1910
TOOLS NEEDED
Goggles
Rubber Mallet
Phillips Head Screwdriver
1¼" Screws x 30*
*Includes extra screws
Top Gate x 2
Handle x 1
Front Panel x 1 Back Panel x 1
Rail x 9
Installation of rails is required for use of bins.
Top Shelf x 1 Bottom Shelf x 1
Bottom Gate x 2 Front Gate x 1
Swivel Caster x 2 Swivel Caster x 2
Hole Hook
Hooks
Tongue
Para Español, vea páginas 9-16.
Pour le français, consulter les pages 17-24.
PARTS
A
D
G
J K L
H I
E F
B C
PAGE 2 OF 24 0721 IH-1495
Figure 2
1. Slide tongues of bottom shelf (I) into back
panel (K). (See Figure 1)
2. Turn cart on side, install four screws through
each swivel caster (B) into bottom of back
panel (K) and up into bottom shelf (I) as
shown. (See Figure 2)
ASSEMBLY
Figure 1
PAGE 3 OF 24 0721 IH-1495
3. Place handle (G) on top of back panel (K) so that
the screw holes on handle tabs line up with holes on
back panel (K). Install screws. (See Figure 3)
4. Insert tongues on one end of top shelf (H) into slots on
back panel as shown. Install 2 screws on each side as
shown. (See Figure 4)
5. Install additional four screws through four tab holes
which are near the four screws just attached.
(See Figure 5)
G
ASSEMBLY CONTINUED
Figure 3
Figure 4
Figure 5
PAGE 4 OF 24 0721 IH-1495
6. Stand cart up.
7. Place the two top gates (D) onto the top shelf (H) so
that gate is in upright position and smooth side of
gate faces interior of cart. When placed correctly,
the hook on the cart handle fits through the hole in
gate; the gate rests on the support molded into the
top shelf. (See Figure 6)
8. Repeat this process for two bottom gates (E). Leave
all gates in the upright position for the rest of the
assembly process. (See Figure 6)
9. Attach front gate (F) to front panel (J) by sliding 2
hinges on front panel into front gate as shown. Leave
front gate in down position, with the smooth side up,
and resting on top of the front panel. (See Figure 7)
ASSEMBLY CONTINUED
Figure 6
Figure 7
PAGE 5 OF 24 0721 IH-1495
10. Attach front panel (J) to bottom shelf (I) by sliding
shelf tongues into slots on front panel (J). Be sure to
place top and bottom gate tabs into holes on front
panel. Attach fixed casters (C) to bottom tabs of front
panel and up into bottom shelf (I). (See Figure 8)
NOTE: Mobile Workstation may be assembled
with or without storage bins
a. If using WITHOUT storage bins, proceed to Step 11.
b. If using WITH storage bins, proceed directly to
Step 12.
11. ONLY IF NOT USING BINS: Secure top shelf (H) to front
panel (J) from underneath with 4 screws. (See Figure 9)
Assembled without bin configuration
ASSEMBLY CONTINUED
Figure 8
Figure 9
PAGE 6 OF 24 0721 IH-1495
12. Pull the top of front panel (J) no more than 2 inches
away from top shelf (H). (See Figure 10)
13. Install first rail (L) by placing one end in the bottom
slot of inside back panel (K) as shown. Make certain
the rail is positioned open-side up. (See Figure 11)
14. Push the front panel back towards the top shelf just
enough so that the rail is held in place in between
the front and back panels.
NOTE: Make certain rail is held in slots on both
sides before proceeding.
15. Install remaining 8 rails in this same manner.
ASSEMBLY CONTINUED
Figure 10
F i g u re 11
PAGE 7 OF 24 0721 IH-1495
16. Beginning with the bottom rail, slowly move front
panel (J) back into position, making sure each rail
secures properly into slots on both panels.
17. If a rail falls out of position, simply place it back into
its slot and continue.
18. When all 9 rails are properly positioned, attach front
panel (J) back to top shelf (H). Secure with 4 screws.
Rail kit installation is complete and your Mobile
Workstation is ready to use. (See Figure 12)
See chart on next page
for information on bin configurations.
Maximum capacity:
200 lb. (90 kg.) per shelf
400 lb. (180 kg.) total
Top Shelf
27.75 × 17"
Bottom Shelf
30 × 17"
• Exceeding recommended weight limit may result in instability causing serious injury.
• Maximum weight capacity per shelf is 200 lb. (90 Kg).
• Caution when moving cart on incline or rough surface.
• Cart can tip over if weight is not evenly distributed.
CAUTION!
* You may need to alternately pull the front panel away from
and push it towards the back panel to hold each successive rail
in place.
ASSEMBLY CONTINUED
Figure 12
PAGE 8 OF 24 0721 IH-1495
S-20581 S-20581 S-20581 S-20581 S-20581
S-20581 S-20581 S-20581 S-20581 S-20581
S-20581 S-20581 S-20581 S-20581 S-20581
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-12413
S-12414
S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536
S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536
S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536
S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536
S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536 S-13536
S-12417 S-12417S-12417
S-12417 S-12417S-12417
S-12417 S-12417S-12417
S-13537 S-13537
S-13537 S-13537
S-13537 S-13537
S-12416
S-12419
S-12416
S-12419
S-12416
S-12419
S-12416
S-12419
S-12416
S-12419
S-12416
S-12419
S-12416
S-12419
S-12416
S-12419
S-12420 S-12420
S-12420 S-12420
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
S-12415
S-12418
BIN COMBINATIONS
NOTE: S-14454, S-12421 and S-12422 are not recommended for use with cart due to length of bins.
1
-800-295-551
0
uline.com
COMBINATIONS FOR ULINE BINS
(OPTIONAL FEATURE FOR WORKSTATION)
3” tall / 4” wide bins: (including S-12413 and S-12414)
Fit 8 per row, 40 on each side, 80 bins total
5” tall / 5½” wide bins: (including S-12415 and S-12418)
Fit 6 per row, 18 on each side, 36 bins total
5” tall / 11” wide bins: (including S-12417)
Fit 3 per row, 9 on each side, 18 bins total
7” tall / 8” wide bins: (including S-12416 and S-12419)
Fit 4 per row, 8 on each side, 16 bins total
4” tall / 4” wide bins: (including S-13536)
Fit 8 per row, 40 on each side, 80 bins total
5” tall / 6” wide bins: (including S-20581)
Fit 5 per row, 15 on each side, 30 bins total
5” tall / 16½” wide bins: (including S-13537)
Fit 2 per row, 6 on each side, 12 bins total
7” tall / 16½” wide bin: (including S-12420)
Fit 2 per row, 4 on each side, 8 bins total
PAGE 9 OF 24 0721 IH-1495
800-295-5510
uline.mx
ESTACIÓN DE
TRABAJO MÓVIL
H-1495, H-1496
H-1497, H-1910
HERRAMIENTAS NECESARIAS
Lentes de Seguridad
Mazo de Hule
Desarmador de Cruz
30* Tornillos de 1¼”
*Incluye tornillos adicionales
2 Puertas Superiores
1 Asa
1 Panel Frontal 1 Panel Trasero
9 Rieles
Requiere instalación de rieles para
usar con gavetas.
1 Repisa Superior 1 Repisa Inferior
2 Puertas Inferiores 1 Puerta Delantera
2 Ruedas Giratorias 2 Ruedas Fijas
Orificio Gancho
Ganchos
Lengüeta
PARTES
A
D
G
J K L
H I
E F
B C
PAGE 10 OF 24 0721 IH-1495
Diagrama 2
1. Deslice las lengüetas de la repisa inferior
(I) para insertarlas en el panel trasero (K).
(Vea Diagrama 1)
2. Voltee el carrito de lado, inserte cuatro
tornillos en cada una de las ruedas
giratorias (B) para fijarlas a la parte inferior
del panel trasero (K) e insertarlas a través
de la repisa inferior (I) como se muestra.
(Vea Diagrama 2)
ENSAMBLE
Diagrama 1
Questo manuale è adatto per i seguenti modelli
3
Indice
Lingue:
Altri manuali U-Line Scrivania
