Ubee DVW32CB Manuale utente

Ubee Interactive — www.ubeeinteractive.com

1 Ubee DVW32CB – Safety and Installation Product Insert v1.0

DVW32C Advanced Wireless Voice

Gateway - Safety and Installation

Product Insert

Federal Communications Commission

(FCC) Interference Statement

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one of the

following measures:

 Reorient or relocate the receiving antenna

 Increase the separation between the

equipment and receiver.

 Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

 Consult the dealer or an experienced radio/TV

technician for help.

FCC Regulatory Information

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired operation.

There is one statement for this product:

 Only the type of PCB PIFA antenna tested

Ubee Interactive — www.ubeeinteractive.com

2 Ubee DVW32CB – Safety and Installation Product Insert v1.0

may be used.

Devices will not permit operations on channels

120-132 for 11a and 11n/a which overlap the

5600 - 5650 MHz band.

FCC Caution: Any changes or modifications not

expressly approved by the party responsible for

compliance could void the user's authority to

operate this equipment.

For product available in the USA/Canada market,

only channel 1 ~ 11 can be operated. Selection

of other channels is not possible.

For operation within 5.15 ~ 5.25GHz frequency

range, it is restricted to indoor environment.

FCC Radiation Exposure Statement:

This device complies with FCC radiation

exposure limits set forth for an uncontrolled

environment. This device should be installed and

operated at a minimum distance of 25cm

between itself and your body.

This device and it's antennas(s) must not be

co-located or operating in conjunction with any

other antenna or transmitter except in

accordance with FCC multi-transmitter product

procedures.

Safety Notices

Read these instructions carefully before

operating the device. It is important to be aware

of these safety instructions. Install the device

according to these instructions and keep this

guide for future reference.

1. Do not use this device in a humid space, in

the rain, or near splashing water.

2. Do not install during thunder or lightning

storms.

3. Do not cover any ventilation openings in the

device case.

4. Do not place the device near heat sources

Ubee Interactive — www.ubeeinteractive.com

3 Ubee DVW32CB – Safety and Installation Product Insert v1.0

such as radiators or stoves.

5. Clean the device only with a clean, dry cloth.

Do not use liquid or chemical cleaners.

6. Avoid static discharge when touching the

device by first touching the coaxial connector

of the coaxial cable.

7. Installation of the device should include

grounding the coaxial cable to the earth at the

building entrance per ANSI/NFPA 70 and the

National Electrical Code (NEC, in particular,

Section 820.93, Grounding of the Outer

Conductive Shield of a Coaxial Cable). The

device is designed for IT power systems with

phase-to-phase voltage at 90~132VAC.

8. Disconnecting the Device: If the device

becomes damaged or encounters some other

abnormality, disconnect the power plug from

the AC wall outlet immediately.

9. The device should be installed in a location

not to exceed the maximum temperature of

40 degrees Celsius (104 degrees

Fahrenheit).

10.When this device is placed upright with the

aid of the stand, the stand must be fixed at a

90-degree angle to the device. Otherwise, the

device will have the risk of tipping over.

11.Keep the device away from Children and

Pets.

12.Place the device on a cool surface. Failure to

do so may result in overheating which can

cause extreme damage.

13.Do not modify or attempt to disassemble the

device. Use it only according to the

instructions.

14.Do not dispose of the device in a trash

container. Please recycle.

15.This product must be installed upright.

Ubee Interactive — www.ubeeinteractive.com

4 Ubee DVW32CB – Safety and Installation Product Insert v1.0

Installation

To install this device, follow the procedures

below and refer to the following page for a

connection diagram.

1. Connect one end of a coaxial cable (not

included) to the CABLE port on the device.

Connect the other end to a cable splitter or the

cable wall outlet. Be sure not to bend or over

tighten the cables as this may strain the

connector and cause damage. If you plan to

connect the device and a television to the

same cable wall outlet, you must use a cable

line splitter (not included).

2. Connect one end of the supplied Ethernet

cable to one of the ETHERNET ports (ETH1

to ETH4) on the device. Connect the other

end to the ETHERNET port on a PC. Note:

Category 5e or Category 6 Ethernet cables

with RJ-45 connectors must be used when

connecting Ethernet devices to the LAN ports.

This ensures Gigabit Ethernet speeds (unless

the computer does not support it).

3. Connect one end of an RJ-11 phone cable to

one of the TEL ports on the device (a port that

has been provisioned for voice service as

specified by the service provider). Connect the

other end to the phone port of the telephone.

Note: If voice service is not provisioned

through the service provider, telephone

service is not available.

4. Connect the power cord to the POWER port

on the device. Plug the other end of the power

cord into the AC wall outlet. Important: Use

only the power cord that is shipped with the

device.

Ubee Interactive — www.ubeeinteractive.com

5 Ubee DVW32CB – Safety and Installation Product Insert v1.0

Wall-Mount Installation

You can mount the device on a wall using the 2

mounting brackets on the bottom of the device.

We recommend that you use two round or pan

head screws.

1. Install two screws horizontally apart on a wall

using the measurement shown to the right.

The screws should protrude from the wall so

that you can fit the device between the head

of the screw and the wall. If you install the

screws in drywall, use hollow wall anchors to

ensure that the unit does not pull away from

the wall due to prolonged strain from the cable

and power connectors.

2. Remove the device from the product package.

3. Mount the device on the wall.

4. Refer to the following figure.

The Distance of the Pothook (Horizontal)

The Screw’s Size (mm)

163mm

(

6.4 inches

)

B C

A 6.65+/-0.35

B 1.9+/-0.15

C 19.0+/1.20

Ubee Interactive — www.ubeeinteractive.com

6 Ubee DVW32CB – Safety and Installation Product Insert v1.0

Additional Information

1. RESET Button (back of device): This button

resets the device to factory defaults. Using a

pointed object, insert it into the button opening,

and hold for more than 10 seconds. The

device will reset and reboot. Note: Not all

parameters are reset to factory defaults. Refer

to the User Guide for more information.

2. Battery (bottom of device): A slot is provided

that houses the battery and can be

opened/closed for battery insertion or

replacement.

3. WPS button (top of device): The WPS button

is used for the Wi-Fi Protected Setup (WPS)

method to connect a Wi-Fi device to the

DEVICE. Refer to the User Manual for more

information.

LEDs and Other Device Indicators

See the following diagram and descriptions of the

device’s LED behavior, and the behavior of the

back-panel Ethernet indicators.

LED Indicators (Color = Blue When On):

Power—If On, indicates that the device has

successfully completed internal power-on tests.

LED flashes if power-on fails. Note that the LED

flashes briefly immediately after powering the

device.

US/DS—When the device initializes, the LED

flashes. When the device locks on to channels

and registers OK, the LED is On. When the

device performs a firmware upgrade, the LED

flashes.

On-line—When the device is obtaining an IP

address and configuration file, the LED flashes.

Ubee Interactive — www.ubeeinteractive.com

7 Ubee DVW32CB – Safety and Installation Product Insert v1.0

When device obtains these items, the LED is On.

Wi-Fi—When Wi-Fi is enabled, the LED is On.

When Wi-Fi is disabled, the LED is Off.

Tel 1/Tel 2—The LED is On when a telephone is

on-hook. The LED flashes when a telephone is

off-hook.

MoCA— When MoCA is enabled, the LED is On.

When MoCA is disabled, the LED is Off.

When passing MoCA network traffic, the LED is

flash.

Battery—LED is On when the battery is installed

and charged. LED is Off if no battery is installed.

If the battery is at low power level (30mins left),

the battery LED will flash.

Back Panel Ethernet Indicators

(Color = Orange or Green):

 When an Ethernet device, such as a computer,

is connected to the device, the LED is Orange

when connected at 10/100 Mbps speeds.

 When an Ethernet device, such as a computer,

is connected to the device, the LED is Green

when connected at 1000 Mbps speeds

(Gigabit Ethernet).

 When data is being passed between the

device and the connected device, the LED

flashes.

Altri manuali per DVW32CB

Indice

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente