Ubee DDW3600 Manuale utente
Ubee TI D3.0 WLCM
Model Number: DDW3600
User Manual
Rev. 1.0
November 12, 2009
◆Important Safety Warnings
"Installation" should include bonding the screen of the coaxial cable to the earth at the building
entrance per ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93,
Grounding of Outer Conductive Shield of a Coaxial Cable.
◆Installation
Follow the procedures below to install the hardware. Figure 0 illustrates the connection
relationship.
1. Connect one end of the coaxial cable (not included) to the CABLE port on the modem, and
connect the other end to the cable wall outlet. Be sure not to bend or over tighten the cables as
this may strain the connector and cause damage. If you plan to connect the modem and
television to the same wall outlet, you must use a cable line splitter (not included).
2. Connect one end of the Ethernet cable to the ETHERNET port on the modem, and connect
the other end to the Ethernet port on the PC.
3. Connect one end of the Phone line cable to the VoIP port on the modem, and connect the
other end to the phone port of the phone set.
4. Connect one end of the DC power adapter to the POWER port on the modem, and connect
the other end to an electric outlet on the wall.
◆Connectors on the rear panel of the Modem
This list of connectors describes where to connect the cables and power adapter when
installing the cable modem.
1. POWER: This is where you plug the included power adapter. Remember to use only the
power adapter that came with the Cable Modem.
2. GigE: This is where you plug the Ethernet cable. The other end connects to the Ethernet
port on the PC or NIC.
3. RESET button: This is what you can reset the setting to factory default by pressing button
on more than 10 seconds.
4. CABLE Connector: This is where you connect the coaxial cable (not included) that leads to
the cable splitter (not included) or the cable wall outlet.
5. USB: This is where you plug the USB cable. The other end connects to the USB port on the
PC.
Figure 1 illustrates the connection relationship
◆LEDs on the front panel of the Modem
Please see the LED descriptions below.
LED Color DESCRIPTION
Power Green
Indicates that the cable modem has
successfully completed internal power-on
tests. LED flashes if power-on fails.
DS
Green/Orange Indicates that data is being received from
the cable network. Orange indicates more
than one Channel is bonded. Green
indicates that one Channel is bonded. Prior
to registration, DS would flash slowly to
indicate it’s looking for DS channel.
Post-registration (READY LED is lit), DS
would flash when traffic is being passed.
US Green/Orange Indicates that data is being transmitted from
the cable modem to the cable network.
Orange indicates more than one Channel is
bonded. Green indicates that one Channel
is bonded. LED flash when traffic is being
passed.
Ready Green LED flashes slowly when performing
upstream ranging. LED flashes quickly
when acquiring IPAddress and
Configuration File. LED must remain off if
device receives disable configuration file.
LED must be solid once registered with
network.
WLAN Green Indicates connectivity in the WiFi port LED
flashes when traffic is being passed.
WPS Green TBD
LAN1 to LAN4 Green/Orange
Indicates connectivity between the Ethernet
port on the cable modem and the PC’s
Ethernet port. LED flashes when traffic is
being passed. Green indicates GbE.
Orange indicates that 10/100/1000 is
enabled.
USB
Green Indicates connectivity in the USB port LED
flashes when traffic is being passed.
◆Specification
Operating Environment: 40 degree C max.
DOCSIS RF Requirement Specification
Table 3. DOCSIS RF Specification
US-DOCSIS 2.0 Upstream Output
Parameter Value
Frequency 5 to 42MHz (edge to edge)
Level range (one channel) TDMA;
+8 to +54 dBmV (32QAM, 64QAM)
+8 to +55 dBmV (8QAM, 16QAM)
+8 to +58 dBmV (QPSK)
S-CDMA:
+8 to +53 dBmV (all modulation)
Modulation Type QPSK, 8QAM, 16QAM, 32QAM, 64QAM, 128QAM and 256QAM
Modulation Rate (nominal) TDMA: 160, 320, 640, 1280, 2560 and 5120 kHz
S-CDMA: 1280, 2560, and 5120 kHz
Bandwidth TDMA: 200, 400, 800, 1600, 3200 and 6400 kHz
S-CDMA: 1600, 3200 and 6400 kHz
Output Impedance 75 ohms
Output Return Loss > 6 dB (5 – 42 MHz)
Connector F connector
US-DOCSIS 2.0 Downstream Output
Parameter Value
Center Frequency 91to 857 MHz (+/- 30 kHz)
Level Range (one channel) -15 dBmV to +15 dBmV
Modulation Type 64QAM, 256QAM and 1024QAM (Three Demodulators)
Symbol Rate (nominal) 5.056941 Msym/s ( 64QAM) and
5.360537 Msym/s (256QAM)
Bandwidth 6 MHz
Total Input Power < 30 dBmV (40-900 MHz)
Input Load Impedance 75 ohms
Input Return Loss > 6 dB (88-860 MHz)
Connector F connector
DOCSIS 3.0 Upstream Output
Parameter Value
Frequency 5 to 42 MHz (edge to edge)
Level range (one channel) TDMA/ATDMA;
+17 to +57 dBmV (32QAM, 64QAM)
+17 to + 58 dBmV (8QAM, 16QAM)
+17 to +61 dBmV (QPSK)
S-CDMA:
+17 to +56 dBmV (all modulation)
Modulation Type QPSK, 8QAM, 16QAM, 32QAM, 64QAM, 128QAM and 256QAM
Modulation Rate (nominal) TDMA: 160, 320, 640, 1280, 2560 and 5120 kHz
S-CDMA: 1280, 2560, and 5120 kHz
Bandwidth TDMA: 200, 400, 800, 1600, 3200 and 6400 kHz
SCDMA Codes per Sub
Frame 1 to 128
S-CDMA: 1600, 3200 and 6400 kHz
Output Impedance 75 ohms
Output Return Loss > 6 dB (5 – 42 MHz)
Connector F connector
US-DOCSIS 3.0 Downstream Output
Parameter Value
Center Frequency 88 to 1002 MHz (+/- 30 kHz)
Level Range (one channel) -15 dBmV to +15 dBmV
Modulation Type 64QAM, 256QAM
Symbol Rate (nominal) 5.056941 Msym/s ( 64QAM) and
5.360537 Msym/s (256QAM)
Bandwidth 6 MHz (Alpha = 0.18 @ 64QAM & 0.12 @ 256QAM)
Capture Bandwidth Supporting four channel bounding on continuous 64MHz CBW
Total Input Power < 36 dBmV
Input Load Impedance 75 ohms
Input Return Loss > 6 dB (88-1002 MHz)
Connector F connector
WLAN RF Requirement Specification
a) frequency rage：
2.412GHz to 2.462GHz
b）EUT frequency list：
the following frequency is point to centre frequency
1.There are 11 channel at 802.11 b/g/ n model HT20
Channel
ID Frequency
(MHz) FCC(USA)
1 2412 O
2 2417 O
3 2422 O
4 2427 O
5 2432 O
6 2437 O
7 2442 O
8 2447 O
9 2452 O
10 2457 O
11 2462 O
There are 7 channel at 802.11 b/g/ n model HT40
Channel
ID Frequency
(MHz) FCC(USA)
3 2422 O
4 2427 O
5 2432 O
6 2437 O
7 2442 O
8 2447 O
9 2452 O
c）modulation：
Standard Data Rate
(Mbps) modul. coding
DSSS-CCK 1 BPSK
DSSS-CCK 2 QPSK
DSSS-CCK 5.5 CCK
11b DSSS-CCK 11 CCK
OFDM 6 BPSK
9 QPSK
OFDM 12 QPSK
OFDM 18 QPSK
OFDM 24 16QAM
OFDM 36 16QAM
OFDM 48 64QAM
11g OFDM 54 64QAM 3/4
MCS8 13 BPSK 1/2
MCS9 29 QPSK 1/2
MCS10 39 QPSK 3/4
MCS11 52 16QAM 1/2
MCS12 78 16QAM 3/4
MCS13 104 64QAM 2/3
MCS14 117 64QAM 3/4
11n 20MHz 2 streams MCS15 130 64QAM 5/6
MCS8 27 BPSK 1/211n 40MHz 2 streams
MCS9 54 QPSK 1/2
MCS10 81 QPSK 3/4
MCS11 108 16QAM 1/2
MCS12 162 16QAM 3/4
MCS13 216 64QAM 2/3
MCS14 243 64QAM 3/4
MCS15 270 64QAM 5/6
Test Channels Rates
Mbps Conditions Mode Antenna Limits
Tx power
802.11g 1,6,11 6 @target power 20dBm 0&2
802.11g 1,6,11 36 @target power 20dBm 0&2
802.11g 1,6,11 48 @target power 19dBm 0&2
802.11b 1,6,11 @target power 19dBm 0&2
802.11n 1,6,11 MCS0/8 @target power 20dBm HT20/40 0&2
802.11n 1,6,11 MCS4/12 @target power 20dBm HT20/40 0&2
802.11n 1,6,11 MCS5/13 @target power 18dBm HT20/40 0&2
802.11n 1,6,11 MCS6/14 @target power 14dBm HT20/40 0&2
802.11n 1,6,11 MCS7/15 @target power 12dBm HT20/40 0&2
+/-2dB(ex
pect the
band
edge
power)
Test Channels Rates
Mbps Conditions Mode Antenna Limits
Tx Spectral Mask
802.11g 6 @+/-9MHz offset 0&2 0dBr
802.11g 6 @+/-11MHz offset 0&2 -20dBr
802.11g 6 @+/-20MHz offset 0&2 -28dBr
802.11g 6 @+/-30MHz offset 0&2 -40dBr
802.11n 6 @+/-9MHz offset HT20 0&2 0dBr
802.11n 6 @+/-11MHz offset HT20 0&2 -20dBr
802.11n 6 @+/-20MHz offset HT20 0&2 -28dBr
802.11n 6 @+/-30MHz offset HT20 0&2 -45dBr
802.11n 6 @+/-19MHz offset HT40 0&2 0dBr
802.11n 6 @+/-21MHz offset HT40 0&2 -20dBr
802.11n 6 @+/-40MHz offset HT40 0&2 -28dBr
802.11n 6 @+/-60MHz offset HT40 0&2 -45dBr
Channel Accuracy
802.11g
/n 6
@2437MHz center
frequency( 25±3℃) 0&2 +/-25ppm
Packet Error Rate (PER)
802.11g 1,6,11 @date rate=6,36,48,54
Mbps 0&2 <10%
802.11n 1,6,11 @date rate=MCS0/8,
MCS5/13, MCS6/14 &
MCS7/15 HT20 0&2 <10%
802.11n 1,6,11
PER<10% @date
rate=MCS0/8,
MCS5/13, MCS6/14 &
MCS7/15
HT40 0&2 <10%
Receiver Sensitivity Test
802.11g 1,6,11 @10% PER/1000 Byte
Pack size/48,54Mbps 0&2 <-70dBm
802.11n 1,6,11 @10% PER/1000 Byte
Pack size/ MCS6/14 &
MCS7/15 HT20 0&2 <-68dBm
802.11n 1,6,11 @10% PER/1000 Byte
Pack size/ MCS6/14 &
MCS7/15 HT40 0&2 <-63dBm
◆ Safety Notices
1. When this device is placed upright with the aid of the stand, the stand must be fixed at a 90
degree angle to the cable modem；otherwise the device will have the risk of tipping over.
2. "Installation" should include bonding the screen of the coaxial cable to the earth at the
building entrance perANSI/NFPA 70, the National Electrical Code (NEC), in particular
Indice
Altri manuali Ubee Modem
Ubee
Ubee DDM3513 Manuale utente
Ubee
Ubee DDM354 Manuale utente
Ubee
Ubee U10C035 Manuale utente
Ubee
Ubee DDW3611 Manuale utente
Ubee
Ubee DDW262.G Manuale utente
Ubee
Ubee Interactive DDM3500 Manuale utente
Ubee
Ubee DDM3521 Manuale utente
Ubee
Ubee DDW3612 Manuale utente
Ubee
Ubee DDW365 Manuale utente
Ubee
Ubee U10C019 Manuale utente
