UCHIDA AeroDieCut Manuale utente
OPERATION MANUAL
UCHIDA YOKO CO., LTD., TOKYO, JAPAN
79-231 V1.02
AeroDieCut OPERATION MANUAL
1
・Use machine only after reading the "Safety Instructions" given below carefully.
・These safety instructions are given to ensure that the machine will be used safely and
properly and to prevent operators from sustaining harm and injuries.
・This equipment is not suitable for use in locations where children are likely to present.
Explanation of markings
Marking
Meaning of marking
Warning
This symbol stands for immediate danger threatening the life and health
of persons. Disregarding these instructions may cause severe damage
to health and even serious injuries.
Caution
This symbol stands for an endangering situation that may occur.
Disregarding these instructions may lead to slight injuries or damage to
property.
Definition of Symbols and Notes
In this manual the following names and signs stand for possible dangers.
Caution
This symbol stands for an endangering situation that may occur.
Disregarding these instructions may lead to slight injuries or damages
to property.
Note
This symbol stands for notes, operational hints, and other useful
information.
They are convenient for exploiting the machine’s functional abilities.
SAFETY INSTRUCTIONS
Explanations of the illustrations used in the Safety Instructions are given as follows:
Warning
1. Don’t put hands inside work area. May result in severe injury.
2. Don't touch any rotating part. There is a danger of receiving an injury.
3. Don't open the cover of the equipment. There is a danger of receiving an injury or
electric shock.
4. Be sure to connect the power cord to a grounded outlet. If the ground is not securely
connected, it could lead to electric shock or fire.
5. Don’t disassemble gas spring. There is a danger of receiving an injury.
AeroDieCut OPERATION MANUAL
2
Caution
1. Don't put a hand into the cover or a clearance between parts.
There is a danger of receiving an injury.
2. Don't bring a hand, face, hair, sleeves of clothes and the like close to the rotating parts
of the machine.
There is a danger of receiving an injury.
3. Do not exceed the MAX level when stacking the paper.
Exceeding it may cause a mechanical failure.
4. When you put a machine into operation, please change into the state where all covers
were closed.
If it works where a cover is opened, there is fear of an injury.
Before use
Read this "Operation Manual" carefully before use. In particular, be sure to read "Safety
Instructions" (page 2 to page 3) to ensure that the machine will be used properly.
Keep the manual at an appointed place with care so that it may be accessible whenever
necessary.
The specifications of this product are subject to change for improvement. Therefore, don't
mistake the "Operation Manual" of one product of the same model for that of another because
descriptions in the "Operation Manual" of products of the same model may differ.
AeroDieCut OPERATION MANUAL
3
Contents
1Introduction.......................................................................................................................5
1.1. Names of parts..........................................................................................................5
1.2. Paper weight / quality................................................................................................6
2. Operating instructions ......................................................................................................7
2.1. Turning the power on ................................................................................................7
2.2. Initial setting ..............................................................................................................8
2.3. Job select ..................................................................................................................8
2.4. Paper setting .............................................................................................................9
2.5. Check the condition of the Press plate .................................................................. 10
2.6. Job start ..................................................................................................................11
2.7. Interruption ............................................................................................................. 12
2.8. Power off ................................................................................................................ 12
3. Job data......................................................................................................................... 13
3.1. Details screen ........................................................................................................ 13
3.2. Imposition control screen ....................................................................................... 14
3.3. Data inputs ............................................................................................................. 15
3.3.1. Explanation of each data inputs ..................................................................... 15
3.3.2. Inputs .............................................................................................................. 16
3.4. Data save ............................................................................................................... 18
3.5. Data read ............................................................................................................... 20
3.5.1. Read from Job No........................................................................................... 20
3.5.2. Read from Job-data list .................................................................................. 21
3.5.3. Read input data .............................................................................................. 22
3.6. Change saved data................................................................................................ 22
3.7. Delete saved data .................................................................................................. 23
4. Die board setting ........................................................................................................... 24
4.1. Die board Changing ............................................................................................... 24
4.2. Adjustment of the level of pressurization............................................................... 27
5. Manual control............................................................................................................... 28
5.1. Manual control screen............................................................................................ 28
AeroDieCut OPERATION MANUAL
4
6. Settings.......................................................................................................................... 30
6.1. Settings screen ...................................................................................................... 30
6.1.1. Speed.............................................................................................................. 30
6.1.2. Double feed check .......................................................................................... 31
6.1.3. Paper feed work time...................................................................................... 31
6.1.4. Table position after work................................................................................. 31
6.1.5. Tri-suction ....................................................................................................... 31
6.1.6. Press Conditions............................................................................................. 32
7. Adjustment .................................................................................................................... 34
7.1. Respond for Feeding direction shift ....................................................................... 34
7.1.1. image shift compensation screen................................................................... 34
7.1.2. Cutting position adjustment ............................................................................ 35
7.1.3. Stretch/Shrink adjustment .............................................................................. 36
7.2. Respond for shift of depth direction ....................................................................... 37
7.3. Respond to printing skew....................................................................................... 38
8. Message dialog ............................................................................................................. 39
9. Maintenance .................................................................................................................. 43
10. Troubleshooting ......................................................................................................... 44
11. Product specifications................................................................................................ 46
AeroDieCut OPERATION MANUAL
5
1 Introduction
1.1. Names of parts
No.
Name
No.
Name
01
Feed unit
10
Press plate
02
Feed table
11
Protective plate
03
Depth adjustment handle
12
Die board
04
Joint cable
13
Paper carrying belt
05
Press unit
14
Cutting plate
06
Top cover
15
Plate holder
07
Front cover
16
Press roller
08
Touch screen
17
Caster
09
Ejection table
18
Adjuster
AeroDieCut OPERATION MANUAL
6
Warning
Don’t put hands inside work area.
May result in severe injury.
Don't touch any rotating part. There is a danger of receiving an injury.
Don't open the cover of the equipment. There is a danger of receiving an injury
or electric shock.
1.2. Paper weight / quality
Use suitable paper stocks which weight is 120 to 400gsm (0.005” – 0.016”).
These paper stocks are not suitable in use.
・Papers that has heavily electric static charged. It may cause miss-feed, double feed or
paper jam.
・Papers that are more than 0.125” curled or waved. It may cause miss-feed, double feed
or paper jam.
・Papers that have ink or toner not fused properly. It may cause contaminating the work
and the machine.
・Papers that are too slippery. It may cause miss-feed or inaccurate results.
・Prints that are shrank, stretched or skewed inconsistently. It may cause inaccurate
results.
AeroDieCut OPERATION MANUAL
7
2. Operating instructions
2.1. Turning the power on
Warning
Be sure to connect the power cord to a grounded outlet.
If the ground is not securely connected,
it could lead to electric shock or fire.
ON
OFF
Electric power cord
AC 110-120V
50/60Hz
400W
Opening screen
Home screen
Power on
AeroDieCut OPERATION MANUAL
8
2.2. Initial setting
①After turning on the power , INITIAL SETTING is displayed on the Home screen.
②Press INITIAL SETTING .
③Initial setting starts by automatically.
・Press roller moves to Home position。
・Hold to up the Die board.
④After initial setting is completed , SET UP or START is displayed on the Home
screen.
2.3. Job select
①Set the job data. （Page20）
②Set the Die board on the machine. （Page24）
Home screen Home screen
Home screen
AeroDieCut OPERATION MANUAL
9
2.4. Paper setting
①Enter the number of sheets for operation.
All the sheets on the feed table will feed in case 0 is entered in Quantity.
②If SET UP is displayed on the Home Screen, press SET UP .
③Feed table goes down. when it reaches the bottom, it automatically stops and changes
to the START display.
④Flip through the sheets well before you put them on the feed table.
⑤Set the sheets on the feed table.
Use the paper guide (Large) and paper guides (Small) to fix the sheets.
Home screen
Home screen
Indice
Altri manuali UCHIDA Taglierina
