Uctronics K0073 Manuale utente
Smart Robot Car Kit
Quick Start Guide
Model: K0073
Smart Robot Car Kit
User Guide
M2*4 micro servoscrews
2 bars
M2*10 screws round head
4 bars
PTZ self-tapping screws
4 bars
M2 nuts
4 pieces
M3*12 screws round head
2 bars
5 Pin line tracking module cable
1 piece
4 Pin ultrasonic module cable
1 piece
Fixing tool
1 set
Line tracking module
1 piece
Camera module
1 piece
18650 Battery charge r
1 piece
18650 Battery
2 pieces
M3 nuts
2 pieces
Ultrasonic bracket
1 piece
Servo accessory
2 set
Pan/Tilt/Zoom
1 set
M3 nuts
2 pieces
Battery container
1 piece
Motor drive board
1 piece
M3*5*4 countersunk
headscrews
2 bars
Packing list
M3*30 screws round head
8 bars
M2.5*6 screws round head
4 bars
Chassis
1 piece
Ultrasonic module
1 piece
Deceleration DC motor
4 pieces
Servo
2 pieces
Wheel
4 pieces
Fastener
8 pieces
M3*30 socket screws
2 bars
M3*6 socket screws
2 bars
M3 nuts
2 pieces
M2.5 nuts
4 pieces
M3 nuts
8 pieces
M3*6 screws round head
2 bars
M2.5*25 socket screws
4 bars
M2.5*11 socket screws
4 bars
For Ultrasonic sensor For Line tracking moduleFor Battery container For DC motors
For Raspberry Pi and Driver board
For Pan-and-Tilt Servo
Smart Robot Car Kit
User Guide
15 Pin FPC cable
1 piece
CD
1 piece
SD
1 piece
1DC motors installation
Step 1: Place the DC motor in the position
marked on the chassis
Step 2: Install the DC motor
*8 x M3*30 round head screws
4 x DC motors
8 x M3 nuts
1 x Chassis
8 x T-type fasteners
For example, the Front L and Front R marks should
be matched between the motor and chassis
*
Smart Robot Car Kit
User Guide
After you complete the first 2 steps, your robot car should
look like this:
Smart Robot Car Kit
User Guide
Step 3: Repeat the steps above, until 4 motors are all installed.
2 Wheels installation
*4 x Wheels
Smart Robot Car Kit
User Guide
After a successful motors and wheels installation, your robot
car should look like this (from the down side of the chassis):
3Pan and Tilt servos installation
Step 1: Mount the Pan servo accessory
1 x Servo
1 x Servo accessory
1 x Pan and Tilt accessory
1 x M2*4 round head screw
2 x PTZ self-tapping screws
*
Step 2: Mount the Pan servo
4 x M2 nuts
4 x M2*10 round head screws
*
Smart Robot Car Kit
User Guide
*Flip the chassis over from the last step and find the
center position of the servo before mounting
NOTE: Servo accessories do not fit as perfectly with the screw as
nuts, and you might need to screw harder.
Step 3: Mount the accessory of the Tilt servo
2 x Pan and Tilt brackets
2 x Pan and Tilt accessory screws
*
Step 4: Mount the tilt servo and the camera module holder
1 x Servo accessory
1 x Pan and Tilt bracket
2 x PTZ self-tapping screws
*
Find the center position of the servo before mounting
*
Smart Robot Car Kit
User Guide
Step 5: Mount the servo and camera holder
1 x Servo accessory
1 x M2*4 round head screw
*
Step 6: Mount the camera module
1 x Camera module
*
Note the orientation of the Camera Module
*
Smart Robot Car Kit
User Guide
4Ultrasonic Module installation
Step 1: Mount the ultrasonic sensor to its plastic holder
*1 x Holder for HC-SR04 Ultrasonic Module
1 x HC-SR04 Ultrasonic Module
Step 2: Mount the ultrasonic module to the chassis
2 x M3 nuts
2 x M3*12 round head screws
*
Smart Robot Car Kit
User Guide
You can adjust the direction of the Pan-Tilt servo to the left and
right to better install the nuts of the ultrasonic module and line
follower
Altri manuali Uctronics Auto giocattolo motorizzata
