UDI R/C Swan U42 Manuale utente
Operations Guide
U47
NOVA
Equipped with WIFI Camera
Catalog
Instruction for Drone and Controller 3
Installing & Removing Spare Parts 7
Pre-Flight Checklist 10
Pre-Flight Operation Instructions 11
Functions 14
Using App 16
Spare Parts 17
Troubleshooting 25
www.udirc.com
2
Instruction For Drone And Controller
Drone
A Propeller
Left Right
Front
Rear
Power Switch
B Propeller
Propeller Guard
B Propeller
A Propeller
Camera
Drone Battery
Front LED
(Green)
Front LED
(Green)
Drone Bottom
Housing
Rear LED
(Red)
Rear LED
(Red)
Drone
Cover Housing
Specifications
Drone Size
Drone Weight
Propeller Diameter
248x280x59.0mm
138g
110mm
Max Streaming Video Range/Radius
40m
50m
120 mins
Flying Time 10 mins
Drone Battery 3.7V 1000mAh
Main Motor 8520x4
Max Flying Height 15m
Charging Time for Drone Battery
Max Flying Distance/Radius
www.udirc.com
3
Exploded View
www.udirc.com
01
02
03
07
04
05
06
11
04
06
07
12
06
01 08 13 1409
15
16
17
18
19
20
18
22
19 21
02
11
04
06
07
06
23
13
09
24
25
08
01
02
09 1008
02
03
04
06
07
06
08
09
27
10
26
01
18
19
18
19
4
16 Camera Board
15
No. Name NameNo.
1 Propeller Guards
17 Battery Switchboard
2 Propeller Piston
18 LED Cover
3 A Propeller
19 Cushion
4 Transmission Gear
20 Drone Bottom Housing
5Rear A LED Board
(Red LED/White Plug)
21 Camera Component
6 Copper ring
22 Camera Organic Board
7 Motor holder
23 Switch Button
8 Spindle steel pipe
24 Drone Housing Cover
9 Steel pipe fixings
25 Rear B LED Board (Red LED/Red Plug)
10 Propeller A Motor
B Propeller
26 Front A LED Board (Green LED/White Plug)
11
Front B LED Board
(Green LED/Red Plug) 27 Battery Compartment
12
Propeller B Motor13
Receiving Board14
Receiving Board holder
Controller
www.udirc.com
Power Indicator
Phone Holder Slot
Left Stick Right Stick
Heading Hold
Mode
One Button Take
Off / Landing/
Emergency Stop
Button
Power Switch
Photo
Video
Notice: Taking photo and recording video are available after connecting with
smart phone.
5
Controller Button Functions
Battery Installation
Open the battery cover on the back side of the controller, insert 4 AA batteries
following the polarity indicators. ( Picture 1/2, battery is not included)
1.Make sure the electrodes are correct. 3.Do not mix different kinds of batteries.
2.Do not mix new with old batteries. 4.Do not charge the non rechargeable battery.
Notice:
www.udirc.com
High/Medium/Low Speed
Mode (Press Down)
Trimmer Mode Button
(Press Down)
Alkaline Battery
Picture 1 Picture 2
Battery Cover
High / Medium / Low Speed button:
Left Stick:
Right Stick:
Power Switch:
Press to right switch to High /Medium/ Low Speed.
Move the Stick to forward / backward / left / right to fly the drone up / down / turn left / turn right.
Move the Stick to forward / backward / left / right to fly the drone forward / backward / left / right.
Trimmer Mode Button:
Press down the left stick and turn to the required trimmer direction,
then it will adjust the direction accordingly. Release the stick to exit trimmer mode.
Push up the power switch to turn on the controller, and pull down to turn off.
Heading Hold Mode:
Press to enter Heading Hold Mode. Press again to exit Heading Hold Mode.
Take Off / Landing / Emergency Stop Button:
automatically. Press again and the drone will land automatically. Press and hold the button for
more than 1 second for an emergency landing, the drone propellers will stop and it will land
immediately.
Press once and the drone will take off
Video:
Press down the button, start to record video.
Photo:
Press down the button, start to photograph.
6
Drone Battery
Phone Installation Instruction
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household
trash. Please contact local environmental or waste agency or the
supplier of your model or your nearest Li-Po battery recycling center.
Charging Instruction for Drone Battery
Parts installation
* For faster charging, it is recommended to use an adapter with 5V 2A output current
(not included) to charge the battery
Notice：Make sure that the button on phone is not clamped.
Power BankPhone Charger Computer Charging Car Charger
1. Connect the drone battery with USB cable first and then choose one of the
method as below picture shown to connect with USB plug.
2. The red USB indicator light keeps bright when charging and the light turns
green when fully charged.
www.udirc.com
Picture 3 Picture 4 Picture 5 Picture 6
1. Take out the phone holder and insert into the controller(Picture 3).
2. Pull out upper lamp of the holder ( Picture 4/5), put the phone into the holder,
then release the clamp, and the phone will be fixed on the holder( Picture 6).
7
Propeller installation diagram
When install, put the propeller hole aims to the drone shaft hole, and then press
down until bottom, tighten it with screw, and then put on propeller cover( Pic 8);
when disassemble, loose the screw and then pull out the propeller.
Notice: When install, please make sure correct propeller in place, otherwise
the drone can not work well.
Picture 9
Picture 10
Picture 8
Warning: When pick up the motor, please don’t damage the LED board.
Motors Replacement Diagram
1. To remove the motor, remove the screw from the lampshade first，then take
the lampshade out, unplug the motor connector from LED board and then take
the defective motor out ( Picture 9) .
2. To install the motor, put the motor into motor holder( make sure the motor
press down and also the gears are pairing) and plug the required motor
connector into the LED board socket. Put on the motor cover and fix it with screw.
Notice: The motor’s rotating direction should be the same, or it will not work.
Tips: The motor is consumable. If it is damaged, please buy new motor for
replacement.
www.udirc.com
插 好 插 座 后 ，将 线 理 顺 ，
按箭头方向摆放。
8
When install the propeller guard, attach one buckle to the arm and then push
another buckle in until they locks (Picture 11).
When remove the propeller guard, take it out from buckles on both sides and pull
out the propeller guards.
Propeller guards assembly instruction
When install, push the battery to the end(Picture 12);
When disassemble,you need to squeeze up and down of the battery buckle and
then put out the lipo battery box is fine.
Battery installation diagram
www.udirc.com
Picture 12 Picture 13
Sticker face up
Picture 11
Push here
Battery buckle
9
Pre-Flight Checklist
1. Ensure that the drone battery and controller batteries are fully charged.
2. Ensure that the left stick of the controller is in the middle position.
3. Strictly follow the instructions for the order for turning on and turning off the
controller and drone. Turn on the controller power first and then turn on the
drone power before flying; Turn off the drone power first and then turn off the
controller power when fishing flying. Improper on/off sequence may cause the
drone to fly out of control and could threaten your safety or the safety of others.
Please cultivate a correct habit of turn on and turn off.
4. Ensure the connection between the battery and motor is solid. Vibration during
use may cause a bad connection and the drone could become difficult to control.
5. Improper operation may cause the drone to crash, which may cause motor
defects that could affect flying ability. If this occurs, visit the local distributor to
buy new replacement parts,so that the drone will return to its best status.
Receiver board wire diagram
www.udirc.com
Front
Rear
Positive/ Negative wire pad
+-
Front B LED board socket
Rear A LED board socket
Front A LED board socket
Camera board socket
Rear B LED board socket
10
Altri manuali per Swan U42
4
Indice
Altri manuali UDI R/C Quadricottero
UDI R/C
UDI R/C U842-2 Manuale utente
UDI R/C
UDI R/C U39 Fury Manuale utente
UDI R/C
UDI R/C U52G Manuale utente
UDI R/C
UDI R/C VOYAGER U845Wifi Manuale utente
UDI R/C
UDI R/C Swan U42 Manuale utente
UDI R/C
UDI R/C U28W Manuale utente
UDI R/C
UDI R/C U829 Manuale utente
UDI R/C
UDI R/C FALCON U842 Manuale utente
UDI R/C
UDI R/C U61 Manuale utente
