Ultimate Lock 3000 Series Manuale utente

The Ultimate Lock™ 3000 Series Installation Guide

a. This lock is designed for a right- or left-handed door that opens into the home or ofce with a deadbolt

currently installed at a 2-3/8" or 2-3/4" backset (centered from the edge of the door). It can be installed on an

outward swinging door, but special instructions are required. See www.TheUltimateLock.com for details.

b. To provide maximum protection, The Ultimate Lock™ should be installed in a solid 1-3/4” thick wood door or

steel-skinned, insulation or foam lled door mounted in a double studded door frame.

c. If your door does not already have a deadbolt installed, it is highly recommended that you purchase an

installation jig kit for deadbolts and door handles. These kits include special hole saws, templates, and other aids

to simplify the installation process. If your door has a metal skin, be sure your kit includes Bi-Metal hole saws to

cut the metal door.

If your door jamb/frame is steel, do not remove the hinge screws! See step 2.

Check www.TheUltimateLock.com to get information on installing the striker plate on a steel door frame.

Congratulations on purchasing the nest engineered deadbolt

lock on the market, The Ultimate Lock™. It is vital that your

lock is installed properly to provide the maximum protection

possible. Read these instructions completely before you begin

the installation. More information can be found at our website:

www.TheUltimateLock.com.

IMPORTANT: Register your lock’s serial number!

Go to www.TheUltimateLock.com and click the “Register Your

Lock” link.

• No. 1 and No. 2 Phillips Screw drivers or bits

• Pencil or steel marking pawl

• Electric drill (3/8" chuck) with torque adjustment

• Drill bits:

1/16"(1.5 mm)

3/32" (2.5 mm)

1/8" (3 mm)

9/64" (3.5 mm)

5/32" (4 mm) (supplied in kit)

• Spade bit or forester bit: 3/4", and 1"

• Hammer, steel center punch, and 1/2" and 3/4"

chisels

• Small carpenter’s square (adjustable)

• Pliers (needle nose and regular)

• Spray lubricant (dry Teon, Silicon Spray, or similar)

• Tape measure or 12-inch ruler

• (If no deadbolt installed) Wood or bi-metal hole

saw: 2-1/8" and 1"

• Wood chisel: 1/2" (13 mm)

• Small carpenters adjustable square

Every Ultimate Lock™ is thoroughly inspected before leaving the factory. It is warranted to be free of defects from workmanship and materials for a period

of TEN YEARS from the date of original purchase. Should any trouble develop during the TEN YEAR period, return the complete lock system, freight

prepaid, to Ultimate Lock, Inc. at 3776 Greenbriar Dr., Stafford, TX 77477 or call 1-866-MLS-4005 (1-866-657-4005) for one of Ultimate’s Authorized Service

Centers nearest you. If our inspection shows the trouble was caused by defective workmanship or material, Ultimate Lock™ will repair (or at our option)

replace the lock without charge. Register your Serial Number on line at www.theultimatelocksystems/warranty.com This Warranty does not apply where:

• Repairs have been made or attempted by others

• Repairs are required because of normal wear and tear

• The lock has been abused, misused or improperly installed

• Alterations have been made to the lock or its components

In no event shall Ultimate Lock™ be liable for any indirect, incidental or consequential damages from the sale or use of the product. This disclaimer applies

both during and after the term of the warranty. Ultimate Lock™ disclaims liability for any implied warranties, including implied warranties of “merchantability”

and “tness for a specic purpose”, after the TEN-year term of this warranty. This warranty gives you specic legal rights, and you may also have other

rights, which vary from state to state. Some states do not allow the exclusion or the limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

*Disclaimer: The Ultimate Lock is only as strong as your door frame. Please contact your local locksmith to visit your home and evaluate your current setup.

Before You Start

Tools You Will Need

A Note About Steel Doors

Limited Warranty

1. Identify Your Parts

Carefully unpack and check that all parts are in the package. Identify parts and hardware from Figure 1. Record the

Serial Number (located inside the lock case) and Date Installed for your lock on the back of this instruction booklet

and save this information for future reference. This information will be required if you ever require any warranty.

Key (qty. 2)

Key Lock

Locating Ring

Deadbolt

Bar Support Cushion

Housing

Lock Bolts

Bar

Gear

Platform

Striker

Decorative Cover

Door Frame

Side

Door

Side

Twist Knob

qty. 2

qty. 6

qty. 2

1 inch (25 mm)

2 inches (50 mm)

3 inches (75 mm)

4 inches (100 mm)

(qty. 1) (qty. 2) (qty. 6) (qty. 6) (qty. 2)(qty. 6)(qty. 2) (qty. 2) (qty. 2)

12 3 4 5 6 789

(Not to scale)

Figure 1

2. Reinforce Your Hinges

3. Measure and Mark

a. It is very important to reinforce the hinges of your door to get maximum protection from forced entry. Your

Ultimate Lock™ comes with 12 special screws to secure the hinges to the studs of the door frame, and not the

door jamb. The six shorter screws go into the middle of the door edge if possible or one inside and one outside

hole on a steel-skinned or thin door.

b. See Figure 2 and remove half of the existing screws from each of the three hinges as shown in the diagram. If

the screws in the door are machine screws (NOT wood screws), do not remove them. Some metal doors have a

metal door jamb and use machine screws to hold the hinges to the door.

c. Use the special 5" (127 mm) long x 5/32" (4 mm) diameter drill bit provided to drill out the exposed screw holes

all the way into the studs behind the door frame. The longer screws  go in the frame and the shorter screws 

go in the door side of the hinge. NOTE: If the door is ber glass or steel sheeted, do not pre-drill the holes in

the door hinges unless the screws have trouble going into the door. If you run into resistance getting the screws

into the door, STOP, predrill the screw holes, and screw in the shorter screws until snug. If your drill has

adjustable torque, set the torque to slip just as the screw is snug. This is also an excellent time to lightly lubricate

the hinge pins one at a time with a suitable lubricant to stop squeaks and rust.

Door Frame

Side

Door

Side

Install longer screws 

into door jamb

Install shorter

screws into door

NOTE: Door frame side only gets screws on the inside two holes closest

to center of hinge. Door will either get two screws in center of door or, if

no screws are in center of the door, one screw in the top inside hole and

one screw in bottom outside hole (typically seen on a steel skinned door).

a. For doors with a deadbolt or key lock: Remove the

old lock from the door. Measure the distance from the

center of the hole for the old lock to the edge of the

door. It will be either 2-3/8" or 2-3/4". Also measure

the diameter of the hole in the edge of the door for the

bolt. It should be 1 inch (25 mm) in diameter. Check

that the new deadbolt will slide into the hole. If not, use a

1-inch spade drill and expand the hole to the proper size.

You can now skip to step 4.

b. For doors without an existing deadbolt: See Figure 3

and measure the backset for your door handle/knob. The

center of the knob will either be 2-3/8” or 2-3/4” from

the edge of the door. Also measure the thickness of your

door. Write these measurements down.

c. Your Ultimate Lock™ should be installed 5-1/2 to 6”

(140 to 153 mm) ABOVE the center of the door handle/

knob, and the backset should match the door handle/

knob. Measure this distance above the center of the

existing door handle/knob and draw a horizontal line

from the door edge back approximately 3 inches on both

sides of the door and across the edge of the door (see Figure 3).

5½ to 6 inches

Backset

Measurement

Hole must be

1” in diameter.

Drill out if needed.

Figure 2

Figure 3

For steel doors with steel door jambs: When installing the Ultimate Lock™

in steel doors or wood doors installed in steel door frames that have not yet had

a deadbolt installed in them but have a deadbolt latch hole already in the door

frame, the lock must be installed in line with the hole in the steel door jamb for

the deadbolt striker (usually covered with a plate).

Place the paper drilling template (or install jig) on the centerline of the recess, and

draw a line on the door (Figure 4). This will be the centerline for installing the

lock in the door.

4. A Note About Steel Doors

5. Measure and Mark Holes

”

(60 MM)

”

(70 MM)

D D

PART # 2

FOLD HERE

30° DRILL

GUIDES

1 " -

(38)

1 " -

(44)

2 " -

(51)

DOOR JAMB

DOOR

6. Prepare Your Door

Refer to the backset measurement recorded in step

3b, and determine the appropriate lock center (A

or B) on the paper template or set the drilling jig to

the proper backset. Fold and place the template on

the INTERIOR of the door as shown in Figure 5,

and mark the location of pilot hole A or B. Refer to

the door thickness as measured in step 3b and mark

the deadbolt center hole (G) that matches your door

thickness.

Backset

Measurement

Place paper template

on interior side of door

”

(60 MM)

”

(70 MM)

D D

PART # 2

FOLD HERE

30° DRILL

GUIDES

1 " -

(38)

1 " -

(44)

2 " -

(51)

These steps are not necessary if you are replacing an existing deadbolt lock. The hole for the cylinder lock and

deadbolt will already be in place.

a. Using the 5" long 5/32" bit provided, drill the pilot hole for the lock cylinder as marked in Step 5 (template mark

A or B) to match the backset of the handle/knob). Make sure the drill bit goes straight through the door.

b. Using the same bit, drill the pilot hole for the deadbolt. Make sure the drill bit goes in level, perpendicular and

the pilot hole is in the middle of the door.

c. Using a 2 1/8" hole saw, drill out the hole for the lock

cylinder. To prevent splintering the surface of the door, do

not drill completely through the door from one side, drill

through from both side of the door.

d. Close the door and push a 2 to 2¼" long nail through the

deadbolt pilot hole, from inside the cylinder lock hole, to

mark the location for the striker plate hole (Figure 6).

e. Using a 1" hole saw, spade bit, or forester bit, drill the hole

for the deadbolt (Figure 3). Insert deadbolt and mark its

outline. Use a sharp chisel to mortise the new deadbolt

faceplate 1/8" (3 mm) deep into the edge of the door.

Push nail through pilot hole

to mark location for center

of striker hole.

Figure 4

Figure 6

Figure 5

7. Install Deadbolt

8. Install Key Lock

a. Look at your door from the inside of the house or room and note if the hinges are on the right or left side of

the door.

b. For a door with hinges on the right, install deadbolt with the cross hole at the bottom. For a door with hinges

on the left, install the deadbolt with the cross hole on top (Figure 7).

c. Mark and drill two 3/32" (2 mm)

pilot holes for the two faceplate

screws , insert the deadbolt

properly and install the screws.

The deadbolt face plate should

be ush with the edge of door

not sticking out from the surface

of the edge of the door.

Cross hole at bottom

for hinges on right

Cross hole at top

for hinges on left

Looking at door from inside:

a. Hold new key lock in your left hand, and rotate the at blade to a horizontal position.

b. With the deadbolt RETRACTED, position the key lock on the outside of the door with the locating ring tted

to the back of the key lock, while inserting the at blade (tailpiece) horizontally through the deadbolt crosshole

(Figure 8) .

NOTE: The deadbolt crosshole will be either at the top or bottom of the unit, as determined in steps 7a and 7b

above. Make sure the tailpiece is at (or horizontal) when inserted through the crosshole.

c. Install the two long lock bolts through the platform and screw them into the key lock. Snug up the lock bolts,

but do not fully tighten them at this point. Make sure the tailpiece does not stick out of the platform, with the

black plastic surface, more than 1/8". If it does, remove the lock and use two pairs of pliers to break off the rst

segment of the tail piece. NOTE: Be very careful not to bend the rest of the tailpiece! Now replace the lock

assembly into the door as before and snug up the lock bolts but do not tighten yet. Using the adjustable square

make sure the Platform is square to the edge of the door and the tail piece is in the center of the large hole in

the Platform. With this done, using a #2 Phillips hand screw driver (NOT a power drill), alternately tighten each

lock screw until they are nice and tight but not over tightened as this can cause the housing to bend in the middle

causing the gear hole to collapse where the gear will not turn properly. Instructions on how to x the gear if this

happens are on the web site www.TheUltimateLock.com.

d. Insert the key into the lock and check for correct operation.

You should be able to remove the key at both the locked

and unlocked positions. If the lock does not function

properly, the at blade (tailpiece) is most likely not positioned

correctly.

e. Position the housing over the platform with the round

corners on the front of both pieces matching up on a 2-3/8"

back set and the square corners on the back of both pieces

matching up on a 2-3/4" backset. This will expose six holes,

three top and three bottom. Mark these holes with a pencil

or metal pawl. Remove the housing and using the 9/64"

drill bit, predrill the holes to a maximum depth of 1-1/4".

Clean away all drilling dust. Drilling deeper than 1-1/4" may

penetrate the outside surface of the door. Use masking tape

or a mark on the drill bit to indicate 1-1/4".

Keylock flat

blade/tailpiece

must be horizontal

when inserted

through deadbolt.

Make sure deadbolt

is oriented properly

(See step 7)

Key Lock

Locating Ring

Housing

Lock Bolts

Deadbolt

Figure 7

Figure 8

a. Apply a dry, multipurpose lubricant to moving parts (teeth

of gear, and security bar).

b. Position security bar in place and start gear into hole.

c. Align the arrow on the rst tooth of the gear with the

marking corresponding to the backset measurement

previously recorded and engage the gear teeth (Figure 9),

making sure that at tailpiece of key lock properly mates

with gear cross hole.

d. The gear should slide in smoothly. Using the key in the key

lock, see if the gear turns smoothly. If you cannot turn

the gear smoothly go to www.TheUltimateLock.com for

correction instructions.

9. Install Security Bar

10. Final Lock Assembly

a. Install the housing over the platform and security bar assembly, making sure to align the corners so the six

predrilled holes lineup with the holes in the housing. Using the six round head screws , attach the housing to

the door and the platform assembly.

b. Position the bar support cushion at the edge of the door in the open area of the lock assembly against the tips

of the housing assembly (Figure 10). If there is any up and down movement, move the bar support cushion

down. The small front edge of the bar support cushion should be even with the edge of a wood door or the

wood core of a steel skinned door. Using the 9/64" drill bit, mark the position of the two holes in the bar

support cushion on the door. DO NOT DRILL HOLES. Remove the bar support cushion and using the

3/32" drill bit, pre drill the two holes. Using screws  found in the small screw package, mount the bar support

cushion to the edge of the door. Using the twist knob and the key, check the lock for smooth operation and

make sure the security bar clears the bar support cushion. If there is a problem, see the troubleshooting

instructions on the web site, www.theultimatelock.com. If the lock works smoothly you are ready to install the

decorative cover.

c. Insert the point of a No. 1 screwdriver into the two mounting holes for the two decorative cover case screws .

Make sure the holes are clear of debris from die cast ash.

d. Install decorative cover and secure with two case screws  using No. 1 Phillips

screwdriver. Alternately tighten each screw until both are tight. DO NOT

OVERTIGHTEN!

e. Use the twist knob and key to exercise the lock. Make sure the lock still turns smoothly.

If the lock hangs or seems to be obstructed while turning, see the troubleshooting

instructions on the web site, www.theultimatelock.com.

f. With security bar retracted, position twist knob in place (oriented vertically), and secure

with screw .

PATENT PENDING

Install gear with

alignment mark

matching the

backset measurement

(Hinges to the LEFT)

(Hinges to the RIGHT)

Figure 9

Bar

Support

Figure 10

11. Install Striker Plate

Platform

Decorative

Cover

Twist Knob

Housing

a. Remove the old deadbolt striker plate from the door frame. Close

the door and see if the new deadbolt aligns with the old hole in

door jamb. If not, use the 1" spade bit to enlarge the old hole for

the new bolt. Make sure it will extend the full 1” depth and the

security button will engage.

b. With the deadbolt partially extended, close the door until the

deadbolt touches the door frame. Mark the top and bottom of the

deadbolt on the edge of the frame.

c. Hold the striker plate on the door frame with the two edge tabs

on the edge of the door frame aligned to the top and bottom of

the deadbolt. Holding the striker plate in place, mark the outside

edge of the striker plate. This will usually be larger than the old

striker plate. Using the chisel, mortise out the frame to t the

Ultimate Lock striker plate. Fit the striker plate in upside down to

check t of mortise. Correct as needed until ush.

d. Holding the striker plate in position, mark the position of two

recessed holes in the striker plate (Figure 12) in the mortise of

the door frame. Using the 3/4" drill bit, start a hole 1/8" in front

of the hole marks and a 3/8" deep hole at a 30 degree angle

(Figure 13). Position the striker plate to make sure it ts ush in

the mortise. Hold the striker plate in position, close the door and

activate the lock to verify both deadbolts clear the striker plate

when thrown. Correct as necessary and then using the 3/32" drill

bit, predrill the two small positioning holes in the striker plate.

Using the 2 small at head wood screws in the small screw

package, attach the striker plate. Close door and verify that the deadbolts clear the striker plate. Using the 5"-

5/32" drill bit provided, predrill the holes for the 3-1/2" mounting screws at a 30 degree angle, to a depth of the

full length of the drill bit. Set the torque on your power drill and using a #2 bit slowly screw the 3-1/2” screws

into the door frame, applying rm pressure on the bit. Close the door and recheck the functioning of the lock.

30°

3/8 inch

1/8 inch

View from top of

door jamb

Mark for

countersink holes

Figure 11

Figure 13

Figure 12

Mark locations for

holes for power screws 

Operation

Non-standard Installations

The Ultimate Lock™ utilizes two deadbolts that work in unison—a mortise deadbolt and a rim deadbolt. The

secondary rim deadbolt protrudes slightly across the door frame and makes it very easy to verify that your door is

locked. To lock your door, simply turn the twist knob counterclockwise 90° until it is horizontal. To unlock the

door, turn the twist knob clockwise 90° until it is vertical. For even more security, The Ultimate Lock™ features a

patented lockout feature that will prevent ANY key from opening the door. To engage the lockout pin, simply press

the button in the locked position until it latches in place. You are now ultimately protected from intrusion!

Installing The Ultimate Lock™ in non-standard congurations requires special

instructions. For guidance on installing the lock on french doors, on outward-opening

doors, or in safe rooms, please visit our website (www.TheUltimateLock.com).

Millennium Lock, Inc

3776 Greenbriar Dr.

Stafford, Texas 77477

Telephone: (713) 266-1400

Fax: (713) 975-9714

For Your Records

It is recommended that you record the details of your Ultimate Lock™ for future reference. This information will

be required if you ever request warranty service.

Date Purchased: ______________________________________________________________

Purchased From: ______________________________________________________________

Serial Number: _______________________________________________________________

12. Finishing Up

You now have the protection of the Ultimate Lock! For added safety, it is recommended that you apply the

“Protected by Ultimate Lock System” decal to the door or a nearby window.

“BE SAFE, LOCK UP, AND SET THE INSIDE SAFETY BUTTON WHEN YOU RETIRE”

TIP: Do not force the screws in. If the screws get too tight before they are all the way in, either apply soap to

screw threads, or carefully remove the screw and re-drill the pilot hole and try again.

For steel door frames: If the door jamb is steel you will have to surface-mount the striker plate and drill 2-5/8"

holes in the steel frame at the point of the mounting holes in the striker plate to accommodate the dimples in the

striker plate. If there is no wood behind the steel frame, you will have to use 1/4" x 1" at-head machine screws

with washers and nuts to mount the striker plate. You will need two 1/4" x 1" at head machine screws, two 5/16"

at washers, two 1/4" at washers, two 1/4" lock washers, and two 1/4" nuts. Holding the 1/4" screw in the hole,

take a pair of curved, long nose pliers and place the 5/16" washer on the screw, then the 1/4" at washer, then the

1/4" lock washer, then the 1/4" nut and tighten them down snug.

Indice

Altri manuali Ultimate Lock Serratura

Ultimate Lock

Ultimate Lock 3000 Series Manuale utente

Manuali Serratura popolari di altre marche

Magic

Magic 105 Manuale utente

Gantner

Gantner GAT NET.Lock 7020 System Guida rapida

Wittkopp

Wittkopp Insys 7202 Manuale utente

Dorma

Dorma Studio Classic Manuale utente

Securam

Securam ECSL-601 Manuale utente

Sudhaus

Sudhaus 3003 Manuale utente

Safety 1st

Safety 1st 48517 Manuale utente

Pado

Pado FDS-10 Manuale utente

Esco

Esco systeQ Series Manuale utente

COMPX

COMPX National D8951 Manuale utente

secureo

secureo Key Box Manuale utente

Stock Loks

Stock Loks C8713 Manuale utente

COMPX

COMPX 1T-058 Manuale del proprietario

Auslock

Auslock T11 Manuale utente

ELCOM

ELCOM 7205 Manuale utente

Stealth SAFES

Stealth SAFES ShadowVault Manuale utente

Knox

Knox KeySecure 5 Manuale utente

Kwikset

Kwikset 48334/01 Manuale utente