Ultimate Support SECOND TIER PRO Manuale utente

V-STAND®PRO / IQ-3000

SECOND TIER PRO

Manual

V-Stand Pro

IQ-3000

Page 2

STEP 1 – PREPARE

V-STAND® PRO OR IQ-3000

Back End

End

Cap

Sleeve

STEP 1A

Identify the back end of

the support arm of the

V-Stand Pro.

STEP 1B

Slide the support arm

back to make room for

second tier assembly

by lifting it up at an

angle, then sliding

it down until fully

extended. Lay arm flat

onto collar.

STEP 1C

Using a flathead

screwdriver, carefully

detach end cap.

STEP 1A

Identify the back end of

the support arm of the

IQ-3000.

STEP 1B

Slide sleeve forward to

make room for second

tier pro assembly.

STEP 1C

Using a flathead

screwdriver, carefully

detach end cap.

Page 3

STEP 2 – ASSEMBLE

SUPPORT ARMS

Small Spring

Riser Tube

Nut

Z-knob

Washer

Support Arm

STEP 2A

Place nut (H) in well of riser tube (B) on opposite side

of teeth. (NOTE: Until assembled, may fall

out – do not lose!)

STEP 2B

Place one small spring (G) in the well at the center of

the teeth of both support arm (A) and riser tube (B).

Press and hold together.

STEP 2C

Place washer on z-knob (E). Assemble by screwing

z-knob (E) into Nut (H) through riser tube (B) and

support arm (A).

STEP 2D

Repeat STEPS 2A-2C for second assembly.

PARTS USED

A. Two (2) Support Arms

B. Two (2) Riser Tubes

E. Two (2) Z-knobs

F. Two (2) Washers

G. Two (2) Small Springs

H. Two (2) Nuts

Page 4

STEP 3B

Release the quick release lever. Slide end clamp onto end of

stand support arm. (NOTE: Make sure end clamp is as far onto

the support arm as possible.)

STEP 3C

Utilizing the leveling bubble, ensure end clamp is level. Secure

by flipping the quick release lever toward end clamp (which

can be tightened, or loosened using a flathead screwdriver).

STEP 3A

Loosen z-knob on end clamp and rotate until bubble level

and riser tube receiver are perpendicular.

STEP 3 – ATTACH CLAMPS AND

ARMS TO STAND

Z-Knob

Support Arm End Clamp

Quick Release Lever

Flathead screwdriver

Riser Tube

Bubble Level

Page 5

STEP 3D

Using printed height markers, choose desired height and adjust

memory collar position to that line. Use included allen wrench

to lock in place. (NOTE: Leave slightly loose, as you will tighten

completely in STEP 3F.)

STEP 3E

Slide riser tub with memory clamp into end clamp receiver.

STEP 3F

Memory Collar will lock into place in end clamp receiver

groove. After ensuring desired height, make sure 1st tier and

2nd tier support arms are parallel. Finally, tighten completely

using included allen wrench.

Allen Wrench

Memory Collar

Riser tub

End Clamp

Receiver Grove

End Clamp Receiver

Page 6

STEP 4A – Adjust Level

Utilizing the leveling bubble, ensure end clamp is level. If desired,

arms can be adjusted to desired angle, in or out of center, by

loosening Z-knob, adjust to desired angle, then tighten.

STEP 4C – Adjust Angle

Adjust angle of support arm by loosening z-knob, adjust to

desired angle, then tighten.

STEP 4B – Set Height

Set and/or change height by installing memory collar at desired

height (use included allen wrench to tighten).

STEP 4 – Adjust Angles

and Height

Page 7

Included Parts:

A. Two (2) Support Arms

B. Two (2) Riser Tubes

C. Two (2) Memory Collar

D. Two (2) End Clamps

E. Two (2) Z-knobs

F. Two (2) Washers

G. Two (2) Small Springs

H. Two (2) Nuts

Included Tool:

I. One (1) Allen Wrench

Other Tool needed:

J. One (1) Flathead

Screwdriver

(Not Included)

Visit ultimatesupport.com

to download a detailed

product manual, read full

warranty details and to

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ultimate Support Rack e supporto

Ultimate Support

Ultimate Support APEX Series Manuale utente

Ultimate Support

Ultimate Support V-Stand Series Manuale utente

Ultimate Support

Ultimate Support APEX Series Manuale utente

Ultimate Support

Ultimate Support Full-Tilt Series Manuale utente

Ultimate Support

Ultimate Support AMP-150 Manuale utente

Ultimate Support

Ultimate Support GENESIS Series Manuale utente

Ultimate Support

Ultimate Support MS-90/36 Manuale utente

Ultimate Support

Ultimate Support Apex Series Manuale utente

Ultimate Support

Ultimate Support AXW-1 Manuale utente

Ultimate Support

Ultimate Support MDS Series Manuale utente

Ultimate Support

Ultimate Support Genesis GS-200 Manuale utente

Ultimate Support

Ultimate Support Deltex Pro Series Manuale utente

Ultimate Support

Ultimate Support GENESIS Series Manuale utente

Ultimate Support

Ultimate Support IQ-3000 Manuale utente

Ultimate Support

Ultimate Support PRO Series Manuale utente

Ultimate Support

Ultimate Support IQ Series Manuale utente

Ultimate Support

Ultimate Support MC-125 Manuale utente

Ultimate Support

Ultimate Support MC-125 Manuale utente

Ultimate Support

Ultimate Support Genesis Series Manuale utente

Ultimate Support

Ultimate Support IQ Series Manuale utente

Ultimate Support

Ultimate Support Live Retro Series Manuale utente

Ultimate Support

Ultimate Support BOX 5 Manuale utente

Ultimate Support

Ultimate Support SP-100 Manuale utente

Ultimate Support

Ultimate Support Sunken 6 Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente