Ultra Max 724TA Manuale utente

IL2924

MODELS 760TA- & 772TA-

Not approved for Canada

ANSI/NSF 4

ELECTRIC

GRIDDLES

MODELS

724TA, 736TA, 748TA, 760TA, 772TA

CHROME MODELS

724TCHSA, 736TCHSA, 748TCHSA, 760TCHSA, 772TCHSA

Installation and

Operation

Instructions

2M-Z16214 Rev. A 11/14/14

724TA

These symbols are intended to alert the user to the presence of

important operating and maintenance instructions in the manual

accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the

manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes,

improvements, additions or replacements for previously purchased

equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change

without notice. While Star International Holdings Inc., Company exercises

good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information

provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.

Please record the model number, serial number, voltage and purchase date in the area below and have it ready when

you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business 8:00 am to 4:30 p.m. Central Standard Time

Hours:

Telephone: (314) 678-6303

Fax: (314) 781-2714

E-mail [email protected]

[email protected]

W[email protected]

Website: www.star-mfg.com

Service Help Desk

Authorized Service Agent Listing

Reference the listing provided with the unit

for an updated listing go to:

Website: www.star-mfg.com

E-mail [email protected]

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive

St. Louis, MO 63143

U.S.A

2M-Z8514, Ultra-Max Electric Griddle

GENERAL INFORMATION

This equipment is designed and sold for commercial use only by personnel trained and experienced

in its operation and is not sold for consumer use in and around the home nor for use directly by the

general public in food service locations. For equipment to be used by the general public, please

contact the factory.

INSTALLATION

The griddles are equipped for the voltage indicated on the nameplate mounted on the front panel.

They will operate on alternating current (AC) only.

DO NOT CONNECT TO DIRECT CURRENT (DC).

The installation of the electric griddle should conform to the:

NATIONAL ELECTRIC CODE AND ALL LOCAL ELECTRIC CODES AND

ORDINANCES AND THE LOCAL ELECTRIC COMPANY RULES AND

REGULATIONS

For your protection we recommend that a qualied electrician install this griddle. He should be

familiar with electrical installations and all electric codes. Proper connections and power supply are

essential for efcient performance. The external wiring should be in conduit or an approved type

of exible cable suitable for operation at the temperature indicated on the wiring diagram, and of a

proper size to carry the load. The supply circuit should be properly fused and equipped with a means

of disconnecting, as required by local electrical code. THE BODY OF THE GRIDDLE SHOULD BE

GROUNDED (DO NOT GROUND TO A GAS SUPPLY LINE).

EXHAUST CANOPY

Griddles inherently create a good deal of heat and smoke and should be installed under an efcient

exhaust hood with ame proof lters. A vertical distance of not less than 48” shall be provided

between the top of the appliance and lters or any other combustible material. Exhaust installation

must conform to local codes.

AIR SUPPLY: Provisions for adequate air supply must be provided.

GENERAL OPERATING PROCEDURES

The Ultra-Max series electric griddles may be wired for operation in the eld for either 1-phase or

3-phase power supplies by making line connections at the junction box(es) located at the rear of the

unit. Models 724T-230/400V, 736T-230/400V & 748T-230/400V, should be wired for 3-phase power

supply only. Two junction boxes are provided on the 760T & 772T for making line connections.

CONNECTING POWER SUPPLY

Detach cover on junction box at rear of unit. There is a terminal block for the supply connection in the

junction box. Wires can be rerouted in the terminal block for 3phase hook-up. See wiring diagrams

and model voltage on unit panel

LOCATING AND LEVELING THE UNIT

Do not install the unit closer than 1-inch from a side wall and/or closer than 1-inch from a rear

wall. Make sure the unit is properly ventilated. Level unit by adjusting the (4) feet which have an

adjustment of 1-3/4” (43.75mm) for accurate leveling and perfect line-up with other Ultra-Max series

units.

CAUTION

WARNING

2M-Z8514, Ultra-Max Electric Griddle

GENERAL OPERATING PROCEDURES continued

SEASONING THE GRIDDLE HEATING SURFACE

Before initial use, clean the griddle surface thoroughly with hot soap and water. See Griddle care on

page 4 for further information. After the griddle has been thoroughly cleaned, it should be seasoned

to prevent food from sticking. Before using and after each thorough scouring, season the griddle

heating surface in the following manner.

1. Remove any shipping material from the cooking surface and thouroughly clean the entire grill

with hot soap and water.

2. Turn temperature control dials to 350°F (177°C).

3. Using a clean cloth, not a spatula, brush a thin lm of cooking oil over the griddle cooking surface.

This lm should remain on the hot griddle surface for half an hour.

4. Remove the excess oil and wipe clean.

5. Apply another lm of cooking oil over the hot cooking area for another half hour and again

remove excess oil and wipe clean. The griddle surface should now be ready for use.

Even with careful seasoning, food may, to some extent, stick to the griddle cooking surface until the

griddle plate is broken in.

TEMPERATURE CONTROL

The temperature controls are combination “ON/OFF” switches and thermostats. Turning the dial knob

automatically maintains the selected heat range.

The Ultra-Max electric griddle line has one thermostat for every 12” (30cm) section of griddle that

operates independently of one another. Each thermostat controls the section of the griddle above it

and may be set at different temperatures as desired.

COOKING

Set the thermostat dial knob at the temperature desired. After a short pre-heating period, the

thermostat will automatically maintain the selected temperature.

IDLING

During idle periods, to save on operating costs, lower the temperature setting of the thermostat to

about 250°F (121°C). It is not necessary to maintain cooking temperature during idle periods, as the

griddle can quickly be reheated to the desired temperature.

SIGNAL LIGHTS

Each thermostat has its own signal light which indicates when the unit’s control knob is in the on

position. Cooking surface will be hot when the control knob is in this position.

2M-Z8514, Ultra-Max Electric Griddle

CAUTION

CLEANING

GRIDDLE CARE (NON-CHOME SURFACES)

It takes very little time and effort to keep the griddle attractive and performing at top efciency.

If grease is permitted to accumulate, it will form a gummy cake and then carbonize into a hard

substance which is extremely difcult to remove. To prevent this condition, the following suggestions

for cleanliness should be followed:

1. After each use, scrape the griddle with a scraper or exible spatula to remove excess grease

and food. A waste drawer is provided for the drippings. If there is an accumulation of burned

on grease and food, the griddle should be thoroughly scoured and re-seasoned. Use pumice

or griddle stone while the griddle is warm. Do not use steel wool because of the danger of steel

slivers getting into the food.

2. Daily, use a clean cloth and a good non-abrasive cleaner to clean the stainless steel body of

the griddle. Wipe the polished front with a soft cloth.

3. At least once a day, remove the waste drawer and wash in the same way as an ordinary cooking

utensil. The drawers are removed by pulling forward until they are released from their track.

GRIDDLE CARE (CHROME SURFACES)

(Chrome surface griddles are marked with “CHS” at the end of the model number designation on the

nameplate.) It takes very little time and effort to keep this Industrial Chrome griddle surface sparkling

clean and performing at top efciency. DO NOT allow grease to accumulate as it will carbonize and

become difcult to remove. To prevent this condition, the following cleaning suggestions should be

followed:

1. Remove excess oil and food regularly with a 4” (100mm) wide razor sharp type scraper and

wipe surface with a damp cloth if desired.

2. Following the scraping, for end of the day cleaning, a damp cloth and a non-silicated, non-

abrasive, non-chlorinated cleaner such as Bon-Ami may be used to wipe surface clean, followed

by wiping with clean wet cloth.

3. Follow steps 2 and 3 from Griddle Care (Non-Chrome Surfaces).

ON CROME SURFACES:

1. Never use pumice, griddle stones, or abrasives on the surface.

2. Never strike the griddle surface with a sharp instrument or spatula edge.

3. Never use steel wool.

4. Never use commercial liquid grill cleaner on the griddle surface.

5. Abusing the surface voids the warranty.

GREASE DRAWER

A grease drawer is located at the front can be removed for cleaning by pulling drawer forward. This

drawer contains hot grease and should be checked and emptied when necessary or at least once a

day.

EXERCISE EXTREME CARE IN HANDLING THE GREASE DRAWER

CONTAINING HOT GREASE.

Never pour large amounts of water onto a hot griddle surface, the sudden

temperature change generated by the steam can cause the surface to warp

and possibly the thermal sensors in your hood re suppression system to

discharge. Instead follow the cleaning procedures in this manual.

MAINTENANCE AND REPAIRS

Contact the factory, a service representative, or a local service company for service or required

maintenance.

CAUTION

2M-Z8514, Ultra-Max Electric Griddle

2M-4497-2 11/21/14

The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.

FOR ASSISTANCE

Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.

In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.

ALL:

*Pop-Up Toasters

*Butter Dispensers

*Pretzel Merchandisers

(Model 16PD-A Only)

*Pastry Display Cabinets

*Nacho Chip Merchandisers

*Accessories of any kind

*Sneeze Guards

*Pizza Ovens

(Model PO12 Only)

*Heat Lamps

*Pumps-Manual

Visit our Website at: www.star-mfg.com Email: [email protected]

THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL

This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in which

the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the transportation

company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of the unit.

LIMITED EQUIPMENT WARRANTY

All workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is limited

to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited to the repair

of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below) should be taken

to the closest Star service agency, transportation prepaid.

>Star will not assume any responsibility for loss of revenue.

>On all shipments outside the United States and Canada, see International Warranty.

* The warranty period for the Ultra-Max, Hot Plates, Griddles, Charbroilers is (3) years parts & labor.

* The warranty period for the Star-Max, Charbroilers, Griddles, Hot Plates, Fryers & Finishing Oven is (2) years parts & labor.

*The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.

* ThewarrantyperiodfortheChrome-MaxGriddlesisve(5)yearsonthegriddlesurface.Seedetailedwarrantyprovidedwithunit.

*The warranty period for Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to

Dura-Teccoatingsfromimpropercleaning,maintenance,useofmetallicutensils,orabrasivecleaners,abrasivepads,productidentiersand

point-of-sale attachments, or any other non-food object tha comes in continuous contact with the roller coating. This warranty does not apply to the

“non-stick” properties of such materials.

>This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts

and ninety (90) days on labor.

>This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or

the Service Center's sub-agency.

>This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and

Operating instructions.

>This warranty is not valid on Conveyor Ovens unless a "start-up/check-out" has been performed by a Factory Authorized Technician.

PARTS WARRANTY

Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted, the labor to replace the part is NOT warranted.

SERVICES NOT COVERED BY WARRANTY

PORTABLE EQUIPMENT

Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.

These products should be taken to the Service Agency for repair:

1. Traveltimeandmileagerenderedbeyondthe50mileradiuslimit

2. Mileage and travel time on portable equipment (see below)

3. Labor to replace such items that can be replaced easily during a daily cleaning

routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.

4. Installation of equipment

5. Damagesduetoimproperinstallation

6. Damages from abuse or misuse

7. Operated contrary to the Operating and Installation Instructions

8. Cleaning of equipment

9. Seasoning of griddle plates

10. Voltage conversions

11. Gas conversions

12. Pilot light adjustment

13. Miscellaneous adjustments

14. Thermostat calibration and by-pass adjustment

15. Resettingofcircuitbreakersorsafetycontrolsorresetbuttons

16. Replacementofbulbs

17. Replacementoffuses

18. Repairofdamagecreatedduringtransit,delivery,&

 installationORcreatedbyactsofGod

* TheModel510FD,510FFFryer.

* TheModel526TOAToasterOven.

* TheModelJ4R,4oz.PopcornMachine.

*TheModel518CMA&526CMACheeseMelter.

* TheModel12MC&15MC&18MCPHotFoodMerchandisers.

* TheModel12NCPW&15NCPWNachoChip/PopcornWarmer.

* All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers.

* All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer.

* All Condiment Dispensers except the Model HPD & SPD Series Dispenser.

* All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series.

* AllQCS/RCSSeriesToastersexcept Model QCS3 & RCS3 Series.

* All Fast Steamer Models except Direct Connect Series.

NOTE: Wattage is 4.35 kw

per heated zone. See unit

nameplate on front panel

for correct supply voltage.

TO CONVERT TO 3 PHASE

MOVE WIRE #3 TO

THE 3RD OPEN TERMINAL

CONNECTOR Z SHOWN.

FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR

AT LEAST 90°C (194°F). USE GAUGE SHOWN OR LARGER.

2M-Z8445

TERMINAL BLOCK

SINGLE PHASE

FIELD WIRING

GROUND WIRE

TERMINAL BLOCK

3 PHASE

FIELD WIRING

GROUND WIRE

PILOT

LIGHT

HEATING ELEMENT

THERMOSTAT

NOMINAL AMPS PER LINE 3 PH.

208V-3 PHASE

20.9

Y Z

240V-3PHASE

X Y Z

18.120.936.2 31.3 18.1

208V 240V

8.7 KW

SINGLE PHASE

41.8 36.3

AWG #8

AWG

X-Y X-Y

#12

AWG

#12

AWG

#12

AWG

#12

AWG

2,4

1,3

2,4

8.7 KW 8.7 KW 8.7 KW

TO CONVERT TO 3 PHASE

MOVE WIRES #4 AND #5 TO

THE 3RD OPEN TERMINAL

CONNECTOR Z SHOWN.

NOTE:

1) FOR SUPPLY

CONNECTIONS USE COPPER

WIRE ONLY, SUITABLE FOR

AT LEAST 90°C (194°F). USE

GAUGE SHOWN OR LARGER.

2M-Z8446

TERMINAL BLOCK

SINGLE PHASE

FIELD WIRING

GROUND WIRE

TERMINAL BLOCK

3 PHASE

FIELD WIRING

GROUND CONNECTOR

GROUND WIRE

THERMOSTAT

HEATING ELEMENT

PILOT

LIGHT

NOMINAL AMPS PER LINE 3 PH.

208V-3 PHASE

36.2

Y Z

36.236.2

240V-3PHASE

X Y Z

31.4 31.4 31.4

208V 240V

13.05 KW

SINGLE PHASE SUPPLY

62.7 54.4

AWG #8

AWG

AWG #6

AWG

X-Y X-Y

1,3

2,6

4,5

1,3,5

2,4,6

13.05 KW 13.05 KW 13.05 KW

TO CONVERT TO 3 PHASE

MOVE WIRES #2 AND #3 TO

THE 3RD OPEN TERMINAL

CONNECTOR Z SHOWN.

FOR SUPPLY CONNECTION USE

COPPER WIRE ONLY, SUITABLE

FOR AT LEAST 90°C (194°F).

USE GAUGE SHOWN OR LARGER.

2M-Z8447

TERMINAL BLOCK

1 PHASE FIELD WIRING

GROUND WIRE

TERMINAL BLOCK

3 PHASE FIELD WIRING

GROUND CONNECTOR

GROUND WIRE

PILOT LIGHT

THERMOSTAT

HEATING ELEMENT

NOMINAL AMPS PER LINE 3 PH.

208V-3 PHASE

55.3

Y Z

240V-3 PHASE

X Y Z

4836.255.3 48 31.4

208V 240V

17.4 KW

SINGLE PHASE

83.6 72.5

AWG

X-Y X-Y

2,3

4,6,8

1,5,7

AWG

1,3,5,7

2,4,6,8

17.4 KW 17.4 KW 17.4 KW

MODEL 724T AND 760T (1SIDE)

MODEL 736T, 760T (1 SIDE), 772T (BOTH SIDES EACH)

MODEL 748T

2M-Z8514, Ultra-Max Electric Griddle

NOTE: Wattage is 4.35

kw per heated zone.

(1450 watts per-element)

See unit

nameplate for correct

supply voltage.

TERMINAL BLOCK

FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR AT LEAST 90°C (194°F).

USE #10 AWG OR LARGER. DO NOT CONNECT TO A SYSTEM OPERATING AT MORE THAN 250

VOLTS TO GROUND

230/400 VOLT Y - 8.7 KW

XYZ

2M-Z8449 REV A 2-20-07

21.8 21.8

21.8

NOM. AMPS

PER LINE

16 16 16 16 16 16

13 13

CONTACTOR

HEATING

ELEMENT

THERMOSTAT

PILOT

LIGHT

TERMINAL BLOCK

FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR AT LEAST 90°C (194°F).

USE #6 AWG OR LARGER. DO NOT CONNECT TO A SYSTEM OPERATING AT MORE THAN 250

VOLTS TO GROUND

230/400 VOLT Y - 13.05 KW

XYZ

2M-Z8552 REV A 2-20-07

32.7 32.7

876

32.7

NOM. AMPS

PER LINE

16 16 16 16 16 16 16 16 16

17 17

13 13 13

CONTACTOR

HEATING

ELEMENT

THERMOSTAT

PILOT LIGHT

TERMINAL BLOCK

FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR AT

LEAST 90°C (194°F). USE #8 AWG OR LARGER. DO NOT CONNECT TO A

SYSTEM OPERATING AT MORE THAN 250 VOLTS TO GROUND

2M-Z8450 REV B 7-15-08

16 16 16

876

543

NOM. AMPS

PER LINE

16 16 16 16 16 16 16 16 16

1717 17

13 13 13 13

CONTACTOR

HEATING

ELEMENT

THERMOSTAT

PILOT

LIGHT

230/400 VOLT Y - 17.4 KW

XYZ

25.2 25.2

25.2

MODEL 724T 230V 3 PHASE

MODEL 736T 230V 3 PHASE

MODEL 748T 230V 3 PHASE

2M-Z8514, Ultra-Max Electric Griddle

FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR

AT LEAST 90°C (194°F). USE #8 AWG OR LARGER. DO NOT CONNECT

TO A SYSTEM OPERATING AT MORE THAN 250 VOLTS TO GROUND

760T 230/400 VOLT Y - 21.75 KW

XYZ

31.5 31.5

16 16 16

31.5

NOM. AMPS

PER LINE

16 16 16 16 16 16 16 16 16

1717 17

13 13 13 13

16 16 16

LEGEND

A HEATING ELEMENT

B CONTACTOR

C PILOT LIGHT

D THERMOSTAT

E TERMINAL BLOCK E

2M-Z11776

MODEL 760T 230/400V Y 3 PHASE

2M-Z8514, Ultra-Max Electric Griddle

NAMEPLATE

21 14

CERTAIN INSTANCES MAY NOT BE AVAILABLE

ILLUSTRATIVE PURPOSES ONLY AND IN

SOME ITEMS ARE INCLUDED FOR

MODEL 724TA, 736TA, 748TA, 760TA, 772TA

STAR MANUFACTURING INTERNATIONAL, INC.

SK2122 REV A. 8/02/2012

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ultra Max Piastra

Ultra Max

Ultra Max 724T Manuale utente

Manuali Piastra popolari di altre marche

Proctor-Silex

Proctor-Silex 25340 Manuale utente

New House Kitchen

New House Kitchen NH33-C Manuale utente

Magikitch'n

Magikitch'n 24 Manuale utente

Black Stone

Black Stone 1650 Manuale utente

Anvil

Anvil FTA7116 Manuale utente

Presto

Presto 07030 Manuale utente

Pit Boss

Pit Boss PB2BGT1 Manuale

Dyna-Glo

Dyna-Glo DGL260SNP Manuale utente

Char-Broil

Char-Broil 19952085 Manuale utente

APW Wyott

APW Wyott HMG-2424 Manuale utente

Pit Boss

Pit Boss Ultimate Griddle PB2BGD2 Manuale utente

Airxcel

Airxcel Suburban Elite SOP-1005A Manuale utente

Keating Of Chicago

Keating Of Chicago MIRACLEAN PRE-2000 Manuale utente

Nexgrill

Nexgrill 720-0786A Manuale utente

Outwell

Outwell FH-3047C Manuale utente

Rankam

Rankam Member's Mark GR2298901-MM-02 Guida di riferimento rapido

Black Stone

Black Stone 1972 Manuale utente

Star

Star Ultra Max 760TA Manuale utente