Ulvac G-5DA Manuale utente

No．P8129-2-02-13

Instruction Manual

for

Direct-Drive Oil Sealed Rotary Vacuum Pump

Model

G-5DA,G-10DA

Before using the product, be sure to read this manual.

Keep this manual in a place where it can be referred to

at any time and look after it carefully.

The contents of this instruction manual are subject to

change without prior notice due to improvements in

performance and the functions of the product.

ULVAC KIKO,Inc.

０．Preface

0.1 Before using this pump

We, ULVAC KIKO,Inc. thank you for purchasing our vacuum pump. When receiving

our vacuum pump, please confirm the product is the same Model No. as you ordered.

Also, check to make sure there are no damages.

To ensure a long life for this pump, read this manual carefully prior to

installation, operation, and maintenance. Also, pay attention to

ascertain the details of safety, specification, and operational

precautions of this pump.

manual shall not be copied without permission by ULVAC KIKO ,Inc. Printed

in JAPAN.

0.2 Safety precautions (General expression)

Safety precautions are identified in this manual using headers DANGER, WARNING,

CAUTION, and NOTE.

"Danger" Indicates major hazardous situations, which present an immediate

threat of death or serious injury.

"Warning" Indicates hazardous situations, which may present a potential

to death or serious injury.

"Caution" Indicates hazardous situations where a potential hazard or

unsafe practice could cause personal injury or equipment damage.

"Note" Indicates undesirable situations where a potential hazard could

cause equipment damage or abnormal operation.

0.3 Safety precautions

When evacuating toxic or inflammable gas, there may be danger of leaking

gas from parts besides inlet port. Practice cautionary steps when working

any kind of gases.

After evacuating toxic gases, the inside of pump and pump oil is

contaminated and toxic. Therefore, handle pump with care during

maintenance.

Do not overhaul or repair this pump.0nly authorized maintenance personnel

should handle this pump to avoid ignition, abnormal action, and electric

shock.

Switch off power before checking or repairing the pump to avoid any

problems (electric shock or personal injury) caused by suddenly starting

up.

Connect an electrical wire cord to ground potential terminal tightly to

avoid electric shock caused by mechanical trouble or electrical leakage.

Do not plug exhaust port or place any materials inside of exhaust port,

because it will reduce pumping speed during operation. Pump explosion,

oil level gauge bursting, or motor over loading are consequences of

excessive pressure inside the pump. This pump is not a compressor. The

maximum pressure inside this pump is 0.03 MPa (GAUGE).

Do not use this pump in an explosive or flammable atmosphere. It may cause

personal injuries or fires.

Do not insert objects, fingers, or another pump body parts into the inlet

port. It may cause electric shock, personal injuries, or fires.

Do not touch the motor body, shaft, or shaft coupling joint during

operation. It may cause personal injuries.

Do not place flammable objects around the pump. It may cause fires. Also,

do not place obstacles around the pump so as to obstruct cooling air.

Abnormal temperature rising may cause burns or fires.

Do not touch the motor while the pump is in operation or when the pump

is still hot immediately after it stops. Touching it will result in burns.

Electric wiring should be carried out in accordance with Electric

Regulation and Instructions. Miswriting may cause fires.

Switch off electric power right away in case of a malfunction to prevent

any troubles. In the case of a malfunction, contact your local agent or

ULVAC KIKO,Inc. Sales and Service Center immediately.

Do not start the pump without pump-oil. Failing to do so will lead to pump

destruction.

0.4 Acceptance and store of product

0.4.1 Acceptance of product

We delivered the pump with the utmost care. After unpacking, please check

up and confirm items as shown below，

(1) The pump is what you ordered.

(2) Spare parts (single use of pump oil, optional parts)

(3) Any damages during transportation.

(4) Any loose screws and nuts.

If you find any abnormal circumstances, please contact your local ULVAC

KIKO,Inc. Sales or Service Center.

0.4.2 Store of product, Installation, Operating condition

This pump is a type of precision equipment; therefore, it is necessary

to satisfy the following items for store product.

(1) Operational temperature and humidity : 7～40°C , 85 % RH >

(2) Installation place should be at an altitude no higher than 1000m above

sea levels for storing or operation.

(3) Required conditions while storing or operating

a. Do not use corrosive or explosive gases.

b. No areas with high moisture.

c. No areas with dust particles.

d. Use indoors only.

e. Do not pile up, or lay on its side.

f. Keep out of direct sun light.

g. Keep away from heat source.

Do not treat with force, or lay on its side. It may cause damage.

0.5 Protective precautions

・100 volt ,single phase,50/60 Hz motor is used for this pump.

・A built-in type thermal protector is equipped for the motor.

・Additional(leakage, etc)protectors are recommended.

Do not apply any voltages other than specifically rated for the motor of

this pump. The over-load protector does not operate normally,

consequently it may cause burning the motor or firing.

CONTENTS

0.Preface ・・・・・・・ 1

0.1 Before using this pump ・・・・・・・ 1

0.2 Safety precautions (General expression) ・・・・・・・ 2

0.3 Safety precautions ・・・・・・・ 3

0.4 Acceptance and store of product ・・・・・・・ 5

0.4.1 Acceptance of product ・・・・・・・ 5

0.4.2 Store of product, Installation, Operating condition

・・・・・・・ 5

0.5 Protective precautions ・・・・・・・ 6

1.For safety operation ・・・・・・・10

1.1 Hazardous of product and safety precautions ・・・・・・・10

1.1.1 DANGER Leakage of hazardous gases and materials ・・・・・・・10

1.1.2 WARNING Electric shock ・・・・・・・10

1.1.3 WARNING Warning explosion ・・・・・・・11

1.1.4 CAUTION High temperature ・・・・・・・11

1.2 Safety data sheet(SDS) ・・・・・・・12

2. General description of the pump ・・・・・・・13

2.1 Principal features ・・・・・・・13

2.2 Dimensional drawings ・・・・・・・14

3. Setting up ・・・・・・・15

3.1 Installation ・・・・・・・15

3.2 Oil charging ・・・・・・・15

3.3 Vacuum tubing ・・・・・・・17

3.4 Electric wiring ・・・・・・・17

3.5 Fluctuations in the power voltage and frequency ・・・・・・・18

4. Operational instructions ・・・・・・・20

4.1 Operational precautions ・・・・・・・20

4.2 Start up operation ・・・・・・・21

4.3 Shut down operation ・・・・・・・22

4.4 Start up procedures in cold climate ・・・・・・・22

4.5 Thermel protector ・・・・・・・23

4.6 Setup oil mist trap (option) ・・・・・・・23

4.7 The restriction in an operation of

oil mist trap (option) ・・・・・・・24

5. Specification ・・・・・・・25

5.1 Ultimate pressure ・・・・・・・25

5.2 Pumping speed ・・・・・・・25

5.3 Required electricity ・・・・・・・25

6. Maintenance, inspection, repair ・・・・・・・27

6.1 Maintenance ・・・・・・・27

6.2 Scheduled inspection ・・・・・・・27

6.3 Oil change ・・・・・・・29

6.4 Replacement of the coupling ・・・・・・・31

6.5 Trouble shooting list ・・・・・・・32

7. Product disposal ・・・・・・・34

8. Maintenance parts ・・・・・・・35

8.1 Maintenance parts list ・・・・・・・35

8.2 Disassembly drawing ・・・・・・・36

Warranty

Safety Data Sheet(SDS)

Check sheet for repair

Sales and Service Centers

DRAWING AND TABLE LIST

Fig-1 General assembly drawing of G-5DA ・・・・・・・14

Fig-2 General assembly drawing of G-10DA ・・・・・・・14

Fig-3 Oil charge to rotary vacuum pump ・・・・・・・16

Fig-4 Vacuum pumping system diagram ・・・・・・・17

Fig-5 Change region of the voltage and frequency ・・・・・・・18

Fig-6 Characteristics of vacuum pumping speed ・・・・・・・26

Fig-7 Characteristics of motor power ・・・・・・・26

Fig-8 Replacement of the coupling ・・・・・・・31

Fig-9 Disassembly drawing of G-5DA ・・・・・・・36

Fig-10 Disassembly drawing of G-10DA ・・・・・・・37

Table-1 Specification ・・・・・・・13

Table-2 Characteristics of the thermal protector ・・・・・・・23

Table-3 Scheduled inspection ・・・・・・・28

Table-4 Trouble shooting list ・・・・・・・32

Table-5 G-5DA Maintenance parts list ・・・・・・・35

Table-6 G-10DA Maintenance parts list ・・・・・・・35

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ulvac Pompa dell'acqua

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente