Unicol RHPL100-HD Manuale utente
Revised 13/12/21
*Please check model specific details before installing*
WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your
carrier claims agent and do not continue the installation until it has been reviewed. Please watch for
pinch points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any
spring loaded parts. Before installing, make sure that the supporting surface will support five times the
combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also
layout all components to ensure that you have all of the required parts before proceeding (see BOM list
on following page). Use of this product for anything other than its specified use may result in failure or
personal injury. This product is intended for indoor use only. We recommend using a qualified trades
person for installation. Use an assistant or lifting equipment to lift and position products.
01865 767676
www.unicol.com
RHPL100-HD
Screen Size: 70-100” Guide Max. Weight: 150kg
2Revised 13/12/21
COMPONENTS
01865 767676
www.unicol.com
INSTALLERS REQUIRED
1-2
# DESCRIPTION QTY
1Heavy Duty Base 1
2PowaLift Mast 1
3Mount Adapter 1
4PZX Screen Mount - Back Plate 1
5PZX Screen Mount - Mounting Arms 2
6CO74 - 7.5cm Castors 4
7Non-Marking Feet 4
8Remote Control 1
9Glass Shelf 1
10 Optional Accessory - Soundbar & VC Mount 1
#TOOLS REQUIRED
1 3/16th Allen Key
2 Pozidrive Screwdriver
3 17mm Spanner
4 Rubber Mallet
2
1
8
5
4
7
6
10
3
9
3
Revised 13/12/21
01865 767676
www.unicol.com
STEP 1
For a trolley version, tap castors with the rubber
mallet until they lock into place ensuring braked
castors are at the front. (as shown above).
For a stand version, insert the plastic feet.
STEP 2
Connect base to mast as shown using the 6 x M12
x 35 hex head screws
STEP 4 (view from rear)
Locate the mount adapter and fix it to the rear of
PZX screen back plate using the 4 x M10 x 25 Hex
Head Screws
STEP 3
In preparation for cabling up later remove the mast
top rear cover by removing the 10 x M6 x 16 Button
Head Allen screws.
If there is an external signal or network cable to
connect, remove the bottom cover. (10 screws).
Put aside and retain.
Front
4Revised 13/12/21
01865 767676
www.unicol.com
STEP 6
Using the griplock (top) and taglock (bottom)
spacers fix the mount arms to the screen
fixing holes. Choose the correct manufacture
recommended fixing screws for your screen from
the universal fixing pack supplied.
If you are fitting the VCCS accessory do it now.
STEP 9
Once centered, ensure the bottom screws are not
tightly fixed and screw down the top screws to
level the screen. Once level tighten bottom screws
to secure the mount.
NOTE: The screen position cannot be adjusted after
the bottom screws have been tightened.
STEP 7
Using another team member, lift the screen up and
gradually offer it up to the back plate. Gently tilting
the screen forward, hook the arms over the lip of
the back plate rail and lower once in position.
Centre the screen horizontally by sliding from side
to side until you are happy with the position.
STEP 5 (view from front)
Fit the mount adapter and fitted screen backplate
to the mast by placing fixing screws from the rear
of the mast through the fixing holes into the adapter
plate and tighten.
5
Revised 13/12/21
01865 767676
www.unicol.com
STEP 10
With the screen fitted, cable it up by routing from
the 4-way power socket up through the aperture in
the mast mount adapter and screen backplate to
the rear of the screen.
STEP 11
External cables route through either base apertures
up the power train to exit at the top of the unit.
There should be enough room without removing
bottom cover. After cabling refit the rear mast
cover by reversing actions in Step 3. To power the
unit, plug the ‘kettle’ connector into the rear of
the unit. Switch on and set up display and any AV
accessories.
STEP 1
Operate the lift motor using manual switch, hand
held remote or LINAK Desk Control App. On the
manual switch and hand held remote press the
UP arrow or DOWN arrow to operate the screen
movement.
Download LINAK Desk Control App from this link:
https://www.linak.co.uk/products/controls/desk-
control-app/#/description or use QR code above.
STEP 2
As soon as power is connected you have 3 minutes
to pair the App by pointing your phone at the unit.
When bluetooth has connected your phone press
‘Connect’. Continue to follow the instructions on
the App to operate the unit.
Note: This App was built for desks but is
recommended by LINAK to operate this unit.
LIFT OPERATION
Manual Switch
Hand Held Remote LINAK Desk Control App
6Revised 13/12/21
01865 767676
www.unicol.com
STEP 2 (OPTIONAL)
With the VCCS assembled hook the top bracket
over the rail of the PZX screen mount back plate.
The normal position is central on the rail but you
can slide it from side to side.
STEP 3 (OPTIONAL)
In order to allow the VC unit to position under the
screen there is up & down adjustment. To adjust
the unit remove or loosen the screws shown
arrowed and move the arms to the desired position.
STEP 4 (OPTIONAL)
The Soundbar fits to the bottom bracket on the
arms. The VC unit fits to the small platform above
the sound bar bracket. Cable up routing up the
arms through the aperture in the PZX screen mount
back plate.
STEP 1 (OPTIONAL)
If fitting the VCCS Soundbar & VC Mount locate the
component shown exploded above. If the screen is
aleady fitted it is easier to remove this in order to fit
the VCCS unit. Reverse steps 8 & 9 above.
VC Unit
Soundbar
ACCESSORIES – SOUNDBAR & VC MOUNT
7
Revised 13/12/21
01865 767676
www.unicol.com
ACCESSORIES – GLASS SHELF
STEP 2 (OPTIONAL)
With the shelf assembled hook the top bracket over
the rail of the PZX screen mount back plate. The
normal position is central on the rail but you can
slide it from side to side.
STEP 1 (OPTIONAL)
Assemble standard or large shelves the same way.
Remove allen screw shown above so that the top
arm clamp can be lifted clear. Position shelf so
that the fixing hole aligns with hole on bottom arm
clamp. Refit top arm clamp into slots and fix with
allen screw.
STEP 3 (OPTIONAL)
Secure the shelf arm by tightening the bottom
securing pozi drive screw against the bottom rail on
PZX backplate. (Diagram viewed from behind).
STEP 4 (OPTIONAL)
Adjust the height of shelf by loosening the pozidrive
screws on the sides of the arm and sliding up or
down. Retighten at desired height.
Indice
Altri manuali Unicol Supporto TV
