UNIMO Technology ChatterBox BiT-4 Manuale utente
BiT-4
USER’S MANUAL
ChatterBox
UNIMO
Technology Co.,Ltd.
CONTENTS
1. GETTING STARTED
Main features
Package contents
Battery charging
Battery
2. INSTALLATION
Installation of Speaker and Microphone
Installation of cradle, bracket and BiT-4 main device
3. BUTTONS AND PORT
4. BASIC FUNCTIONS
Power on / off
Volume up / down
Automatic power off
Voice command
5. SMART-PHONE CONNECTION
Smart-phone pairing
Second Smart-phone pairing
New Smart-phone (the third Smart-phone) replacement
6. MODE CHANGE
Music mode
FM radio mode
1:1 Intercom mode
Universal Intercom mode
4 Riders Multi-Intercom mode
Surround Monitoring mode
Battery power level
7. PHONE FUNCTION
Answering incoming call
Rejecting incoming call
Hanging up the call
Automatic answering
Holding the current call, answering an incoming call
While in calling, rejecting another incoming call
Last number redialing & Speed dial
While being on the phone, switching device between BiT-4 and Smart-phone
8. MUSIC MODE
Enter / Exit music mode
Music play / stop
Fast-forward / Rewind
Switching music between two paired Smart-phones
Music sharing
9. FM RADIO MODE
Entering / Exiting FM radio mode
Playing / Muting FM radio
Scanning channel up / down
Saving channel
Saved channel up / down
10. INTERCOM MODE
Volume control in Intercom mode
1:1 Intercom pairing
1:1 Intercom connection / disconnection
Audio Multi-Tasking
4 Riders Multi-Intercom pairing
4 Riders Multi-Intercom connection / disconnection
4 Riders Multi-Intercom reconnection and reposition
1:1 Intercom automatic re-connection
11. UNIVERSAL INTERCOM PAIRING
Universal Intercom pairing with BiT-4 set as a master
Universal Intercom pairing with Non-ChatterBox product set as a master
Universal Intercom connection / disconnection
Conference call between 1:1 intercom & Universal Intercom
12. SURROUND MONITORING MODE
13. SET UP MODE
Language
Music sharing
VOX
Side Tone
Reset
Exit
14. RESET
Reset
Factory Reset
15. SMART-PHONE APPLICATION CONTROL
16. SOFTWARE UPGRADE
17. SUPPORT
Precaution
Limited warranty
Limitation of liability
Reasons for limited liabilities
Disclaimer of liability
Customer service center
18. FAQ (Frequently Asked Questions)
19. CE/FCC DECLARATION
20. SIMPLE MANUAL
1. GETTING STARTED
Thank you for choosing our ChatterBox BiT-4, Bluetooth Communication System for Motorcycle
helmet.
Main features
Bluetooth V 4.1
1:1 Intercom maximum range up to 700 meters (Refer to FAQ)
4 Riders Multi-Intercom
Universal Intercom
FM Radio
5 Languages voice prompt (English, French, German, Italian, Spanish)
Dual pairing with two Bluetooth devices (Smart-phone, MP3, Navigation etc)
Music sharing
Surround monitoring
Audio Multi-tasking
Answering phone call using VOX
Side Tone (Listening own voice during phone conversation)
Smart-phone Application Control
Usable during charging
Volume of each mode is separately adjustable during Intercom communication
Allowing Intercom to stay connected during a phone conversation
User upgradable firmware
Water Resistance
Package contents
BiT-4 Main device with a built-in battery
USB charging data cable
Microphones for both open-face and full face helmets
Speaker, Velcro for speaker, Velcros for microphones and a Butterfly Mic-holder,
Helmet mounting cradle, Metal Bracket, 2 screws and L-wrench
User manual, Chatterbox Logo sticker
Battery charging
Connect the supplied USB charging data cable with a PC or wall charger.
Be sure to charge the product using the USB charging data cable provided. Charge with a normal
charger of 5V or less than 1.2A. Using a high-speed charger for Smart-phones or a supplementary
battery with high-speed charging (9V, higher than 1.2A) may inflate the battery, cause an explosion,
or damage internal circuits.
With a normal charger, it takes 2.5~3 hours to fully charge. Charging time depends on the
temperature. The Red LED flashes while charging and the Blue LED lights and stay showing the
charging is finished. If the charging is finished disconnect the charging cable. Overcharging may
cause battery inflation and damage the battery.
You can charge BiT-4 with a power bank (an external battery pack) while you are using it. In this case,
the Red LED and Purple LED (Red and Blue LED at the same time) flash alternately. When the
charging is finished, the LED turns and flashes to Blue.
Battery
Please read the following notes. The battery of this product cannot be replaced by user. Always keep
your battery charged enough.
Every battery discharge by itself naturally. If the battery was discharged and not charged for
a long time, the voltage drops under 2.0V, the battery can not be charged again. In this case,
you need to replace the battery if battery replacement is applicable. However, this
replacement can not be covered by warranty.
Do not disassemble the product or do not try to replace the battery. It may cause product
failure. Warranty repair can not be applicable.
Battery capacity may be reduced depending on environmental factors and usage. Life cycle
of Lithium Ion, or Lithium Polymer battery, battery manufacturer guarantees 300 times of
full charges and discharges.
Use or store the product at -15°C and +50°C. Higher or lower temperatures may temporally
cause reduced battery capacity, battery life, or temporary inactivity.
Long exposure of the product to direct sunlight in a hot temperature may cause circuit
failure or battery failure.
Do not use any product damaged by impact, circuit or battery failure may occur.
2. INSTALLATION
Speaker and Microphone Installation
Both microphones for open-face and full-face helmets are provided. Please choose the one that you
intend to use for the type of your helmet.
① Remove the inner pad of the helmet where you want to locate the speakers and microphone.
② Make sure to clean inside of your helmet with alcohol and fully dry the spot where you want to
put the Velcro for the speakers and microphone.
③ For open-face helmet, attach soft Velcro disk inside of the helmet at your chic level and place the
boom-microphone on it and set the white dot on the Microphone-head to face your mouth.
Additionally, fix the boom-stick by using the butterfly shaped holder to support it.
④ For full-face helmet, attach soft Velcro disk on the chin bar of the helmet and attach hard Velcro
disk to the microphone. It is recommended to fix wires with tapes.
⑤ Mount the soft Velcro disks on the liner of your helmet, in the indented part of the helmet
padding, where your ears would line up. For the best sound quality, be sure to locate the
speakers to the right location.
⑥ Attach the right speaker (with the longer wire) to the corresponding Velcro disk that you applied
on the helmet liner. Attach the left speaker (with the shorter wire) to the other Velcro disk.
⑦ Re-install removed inner pad back on the helmet
※ CAUTION: Repositioning of the Velcro stickers of the speakers and microphones more than
one time may result in poor adhesion. ( Velcro stickers are available on the website,
http://www.chatterboxglobal.com/)
Open-Face microphone Ultra Slim Full-face microphone
Speakers Cradle and Bracket
Installation of cradle, bracket and BiT-4 main device
1. Prepare the provided cradle, bracket, screws and L-wrench.
2. Attach the metal bracket with rubber to face cradle to the cradle using screws but do not fully
tighten at this stage.
3. Slide the bracket iron plate into the gap between the helmet shell and the inner pad of the left
side.
4. Now tighten the screws on the bracket to fit the cradle to the helmet firmly using the L wrench.
5. Connect the microphone and speakers to the cradle. Make sure to match the arrow at the end
of the plug and jack.
6. Insert the guide fin on the back of the product along the slide of the cradle and push it down
until you hear the 'click' sound.
※ CAUTION: If screws of the cradle are over-tightened, back of cradle may be bended and this may
result in difficulty setting the BiT-4 main device on the cradle or main product may fall off by shock
or vibration.
3. BUTTONS AND PORT
4. BASIC FUNCTIONS
Power On/Off: Long press POWER BUTTON for 3 seconds.
Volume Up: Press the PLUS BUTTON with intervals of longer than 0.5 seconds.
Volume Down: Press the MINUS BUTTON with intervals of longer than 0.5 seconds.
※ CAUTION: Fast double-pressing within 0.5 seconds will result in searching next / previous song in
Music mode OR that will result in scanning up and down channels in FM radio mode.
Automatic Power-Off: If the BiT-4 main device is not in operation for longer than 60 minutes, the
device will automatically be turned off to save the battery.
※ Automatic Power-off function can be controlled through the Smart-phone application. However,
this function will not be off while a phone call, Intercom call, Music play and FM radio are operating
Voice Command function of your Mobil-phone:
To activate Voice Command function in your Smart-phone through BiT-4 device, after stopping
Music or FM radio, long press PLUS BUTTON longer than 1 second. But make sure the voice
Indice
