UNIVERSAL HARDWARE UH4031 Manuale utente

FASTENERS DOOR OR FRAME RECOMMENDED DRILL SIZES DRILL DEPTH

Machine Screw Hollow Metal or Aluminum #7 (.201") & 1/4-20 Tap *Through One Side

Sheet Metal Screw

Wood Cored

*1-1/4"

3/16"

1/8"

Hardwood

Hollow Metal

PREPARATION FOR FASTENERS

EXTERIOR (and VESTIBULE) DOOR WIDTH MINIMUM DOOR WIDTH (24")

COMPONENTS

THIS VALVE CONTROLS LATCHING SPEED

(SLOWER- TURN CLOCKWISE)

(FASTER - TURN COUNTER CLOCKWISE)

THIS VALVE CONTROLS DOOR SWEEP SPEED

(SLOWER- TURN CLOCKWISE)

(FASTER - TURN COUNTER CLOCKWISE)

STANDARD CLOSING CYCLE

TURN SPEED REGULATING VALVES CLOCKWISE TO SLOW DOWN

OR COUNTER CLOCKWISE TO SPEED UP DOOR MOVEMENT.

OPENING

10°

BACKCHECK

CLOSING SPEED CONTROL

ATTENTION:

BACKCHECK ("BC") VALVE

CONTROLS THE HYDRAULIC

RESISTANCE TO DOOR

OPENING IN BACKCHECK

RANGE. NEVER CLOSE

THIS VALVE COMPLETELY.

IT IS NOT TO PROVIDE A

POSITIVE STOP.

REGULATING SWEEP SPEED & LATCHING SPEED

POWER ADJUSTMENT SCREW. TURN CLOCKWISE

TO INCREASE OR COUNTER CLOCKWISE TO

DECREASE.

TURN BC REGULATING VALVE CLOCKWISE

TO INCREASE OR COUNTER CLOCKWISE TO

DECREASE. NEVER CLOSE THIS VALVE

COMPLETELY.

MOVE FOOT PIVOT TO HOLE AS ILLUSTRATED

LESS POWER MORE POWER

STANDARD POSITION

HINGE EDGE OF DOOR

FOR CUSTOMER CARE CALL TOLL FREE 800-562-5625 OR

[email protected]

INTERIOR DOOR WIDTH MINIMUM DOOR WIDTH (24")

BEFORE INSTALLATION, ADJUST THE SPRING POWER AS SHOWN ON CHARTS BELOW. DO NOT EXCEED THE MAXIMUM TURN. THE SPRING POWER HAS BEEN PRESET TO “0” TURNS FROM FACTORY.

CAUTION: DO NOT BACK

VALVES OUT OF CLOSER

OR LEAK WILL RESULT.

ATTENTION:

ADJUST CLOSING SPEED

TIME TO BETWEEN 4 & 6

SECONDS FROM 90°.

DOORS USED BY:

HANDICAPPED, ELDERLY

OR SMALL CHILDREN MAY

REQUIRE LONGER

CLOSING TIMES.

POWER AND BACKCHECK ADJUSTMENT FOOT POWER

ADJUSTMENT

CAUTION: DO NOT BACK

VALVES OUT OF CLOSER OR

A LEAK WILL RESULT.

Measure door thickness before

drilling pilot holes to prevent drilling

through opposite side

24"

(610mm)

30"

(762mm)

36"

(914mm)

REGULAR ARM &

TOP JAMB SIZE 3 SIZE 4

42"

(1067mm)

SIZE 5

PARALLEL ARM

REGULAR ARM &

TOP JAMB

PARALLEL ARM

SIZE 3 SIZE 4

24"

(610mm)

30"

(762mm)

34"

(865mm)

38"

(965mm)

SIZE 1 SIZE 2 SIZE 3

48"

(1219mm)

SIZE 4

SIZE 1 SIZE 2 SIZE 3 SIZE 4

54"

(1372mm)

SIZE 5

CLOSER BODY

ELBOW SCREW,

LOCK WASHER

& WASHER

PINION COVER

MAIN ARM SCREW

& WASHER

PA PLATE

FOOT

LOCKNUT

FOREARM

PINION SHAFT

DOOR CLOSER

MODEL UH4031 or UH4032 INSTALLATION INSTRUCTIONS

ADJUSTABLE TO SIZES 1-5

POWER ADJUSTMENT

PAGE 1

10809 ZINS-L1163-2T

999-30013

DETERMINE HAND OF DOOR

PULL SIDE

PUSH SIDE

HINGE SIDE OF DOOR

STOP SIDE OF DOOR

HINGE SIDE OF DOOR

THIS IS A RIGHT HAND DOOR

THIS IS A LEFT HAND DOOR

LATCH

LEFT HAND DOOR

RIGHT HAND DOOR

RIGHT

HAND

DOOR

LEFT

HAND

DOOR

PINION

DIMPLE

PINION

DIMPLE

DOOR

PRELOAD

90°

RIGHT

ANGLE

Fig. B

Fig. A

POSITION OF MAIN ARM WHEN

ASSEMBLING TO SPINDLE

1. SELECT DEGREE OF DOOR OPENING. USE DIMENSIONS

SHOWN IN CHART AND ILLUSTRATIONS ABOVE TO MARK

LOCATION OF ATTACHING SCREWS ON THE DOOR AND

FRAME. PREPARE HOLES (See Preparation For Fasteners

chart page 1).

2. DISASSEMBLE FOREARM FROM MAIN ARM BY REMOVING

ELBOW WASHERS AND SCREW.

3. MOUNT MAIN ARM ONTO CLOSER PINION SHAFT, ALIGNING

PINION DIMPLE (see Fig. A.). SECURE WITH MAIN ARM

SCREW AND WASHER.

4. ATTACH CLOSER TO THE DOOR WITH THE SPEED

REGULATING VALVES FACING THE HINGE SIDE OF DOOR.

5. ATTACH THE FOOT OF THE FOREARM TO THE FRAME.

6. ADJUST THE LENGTH OF THE FOREARM TO POSITION THE

FOREARM AT A RIGHT ANGLE TO THE FRAME TO ENSURE

PROPER PRELOAD (see Fig. B).

7. REATTACH MAIN ARM AND FOREARM USING ELBOW

SCREW AND WASHERS. TIGHTEN LOCKNUT ON FOREARM.

8. SNAP PINION CAP ONTO THE PINION AT THE BOTTOM OF

THE CLOSER.

9. ADJUST CLOSER (refer to Speed and Power Adjustment charts

on page 1).

7TO 100°

6TO 120°

3-1/2 TO 180°

UP TO 54"

UP TO 48"

UP TO 38"

UP TO 42"

UP TO 36"

UP TO 30"

*DOOR/WALL/HARDWARE/JAMB CONDITIONS PERMITTING

DIMENSION "A" OPENING

ANGLE

DOOR WIDTH CLOSER SIZE

CW TURNS

OF POWER

ADJUSTMENT

SCREW

INCHES INTERIOR EXTERIOR

178

152

RIGHT HAND DOOR ILLUSTRATED, SAME DIMENSIONS APPLY TO LEFT HAND DOOR

MEASURED FROM HINGE CENTERLINE

DO NOT SCALE DRAWING

DOOR

PINION CAP

SCREW

& WASHER

FOOT

FRAME

9-1/16" (230 mm)

"A" 1 3/4" (44.5 mm)

BC VALVE

SPEED

REGULATING

VALVES

CENTERLINE

OF HINGE

REGULAR ARM INSTALLATION

MODEL UH4031 or UH4032 INSTALLATION INSTRUCTIONS

PAGE 2

999-30013

6" (152 mm)

1" (25 mm)

3/4"

(19 mm)

RIGHT HAND DOOR ILLUSTRATED, SAME DIMENSIONS APPLY TO LEFT HAND DOOR

MEASURED FROM HINGE CENTERLINE

DO NOT SCALE DRAWING

Fig. B

Fig. A

1. SELECT DEGREE OF DOOR OPENING. USE DIMENSIONS

SHOWN IN CHART AND ILLUSTRATIONS ABOVE TO MARK

LOCATION OF ATTACHING SCREWS ON THE DOOR AND

FRAME. PREPARE HOLES (See Preparation For Fasteners chart

page 1).

2. ATTACH CLOSER TO THE FRAME WITH SPEED REGULATING

VALVES FACING THE HINGE.

3. DISASSEMBLE FOREARM FROM MAIN ARM BY REMOVING

ELBOW WASHERS AND SCREW.

4. MOUNT MAIN ARM ONTO CLOSER PINION SHAFT, ALIGNING

DIMPLE (see Fig. A.). SECURE WITH MAIN ARM SCREW AND

WASHER.

5. ATTACH THE FOOT OF THE FOREARM TO THE DOOR.

6. ADJUST THE LENGTH OF THE FOREARM TO POSITION THE

FOREARM AT A RIGHT ANGLE TO THE FRAME TO ENSURE

PROPER PRELOAD (see Fig. B).

7. REATTACH MAIN ARM AND FOREARM USING ELBOW SCREW

AND WASHERS. TIGHTEN LOCKNUT ON FOREARM.

8. SNAP PINION CAP ONTO THE PINION AT THE TOP OF THE

CLOSER.

9. ADJUST CLOSER (refer to Speed and Power Adjustment charts

on page 1).

PINION

DIMPLE

PINION

DIMPLE

DOOR DOOR

PRELOAD

90°

RIGHT

ANGLE

POSITION OF MAIN ARM WHEN

ASSEMBLING TO SPINDLE

JAMB FACE

DOOR

FRAME

FOOT

PINION CAP

SCREW

& WASHER

7TO 100°

6TO 120°

3-1/2 TO 180°

UP TO 54"

UP TO 48"

UP TO 38"

UP TO 42"

UP TO 36"

UP TO 30"

*DOOR/WALL/HARDWARE/JAMB CONDITIONS PERMITTING

DIMENSION "A" OPENING

ANGLE

DOOR WIDTH CLOSER SIZE

CW TURNS

OF POWER

ADJUSTMENT

SCREW

INCHES INTERIOR EXTERIOR

178

152

9-1/16" (230 mm)

1-1/2" (38 mm)

1/2" (13 mm)

"A" CENTERLINE

OF HINGE

VALVE

SPEED

REGULATING

VALVES ON

THIS SIDE

10809 ZINS-L1187-2T

6" (152 mm)

TOP JAMB INSTALLATION

MODEL UH4031 or UH4032 INSTALLATION INSTRUCTIONS

PAGE 3

999-30013

1 3/4" (44.5 mm)

3/4"

(19 mm)

RIGHT HAND DOOR

HINGE SIDE

LEFT HAND DOOR

HINGE SIDE

3-1/8" (80 mm)

MAXIMUM

RIGHT

HAND

DOOR

LEFT

HAND

DOOR

FRAME

"B"

2-3/4" (70 mm)

1-1/2" (38 mm)

3/8" (9.5 mm) 7/16" (11 mm)

3/8" (9.5 mm)

FROM JAMB

STOP FACE

1. SELECT DEGREE OF DOOR OPENING. USE DIMENSIONS SHOWN IN CHART AND ILLUSTRATIONS ABOVE TO MARK LOCATION OF ATTACHING SCREWS ON THE

DOOR AND FRAME. PREPARE HOLES (See Preparation For Fasteners chart page 1).

2. DISASSEMBLE FOREARM FROM MAIN ARM BY REMOVING ELBOW WASHERS AND SCREW.

3. REMOVE THE FOOT FROM THE FOREARM AND DISCARD. Note: DO NOT DISCARD SCREW, WILL NEED IT IN STEP 7.

4. ATTACH CLOSER TO THE DOOR WITH SPEED REGULATING VALVES FACING THE DOOR OPENING.

5. ATTACH THE PA PLATE TO THE TOP FRAME AS SHOWN IN DIAGRAM.

6. BEFORE INSTALLING THE ARM ON THE PINION SHAFT, ROTATE THE PINION WITH A WRENCH 45° TOWARDS THE HINGE EDGE OF THE DOOR TO ALIGN DIMPLE IN

SPINDLE TO MAIN ARM (see Fig. A). FASTEN WITH MAIN ARM SCREW AND WASHER.

7. FASTEN FOREARM TO THE PA PLATE, USING THE SCREW THAT WAS

REMOVED FROM THE FOOT IN STEP 3 AND PA SHOE WASHER INCLUDED IN

SCREW PACK.

8. WITH THE DOOR CLOSED, ADJUST THE FOREARM LENGTH TO SET ARM

ELBOW ABOUT 1-1/2" [38mm] FROM THE DOOR WHEN CONNECTED TO THE

MAIN ARM. USE WASHERS AND SCREW PROVIDED TO SECURE THE PIVOT

CONNECTION. TIGHTEN LOCKNUT.

9. SNAP PINION CAP ONTO THE PINION AT THE BOTTOM OF THE CLOSER.

10. ADJUST CLOSER (refer to Speed and Power Adjustment chart on page 1).

PINION

DIMPLE

RIGHT

HAND

DOOR

LEFT

HAND

DOOR

PINION

DIMPLE

DOOR

7-5/8 TO 100°

6-1/8 TO 120°

4-1/8 TO 180°

UP TO 48"

UP TO 38"

UP TO 36"

UP TO 30"

*DOOR/WALL/HARDWARE/JAMB CONDITIONS PERMITTING

DIMENSION "A" OPENING

ANGLE

DOOR WIDTH CLOSER SIZE CW TURNS OF POWER

ADJUSTMENT SCREW

INCHES INTERIOR EXTERIOR

194

156

105

9-1/4

7-3/4

5-3/4

DIMENSION "B"

INCHES

235

197

146

HINGE SIDE

LEFT HAND DOOR

HINGE SIDE

RIGHT HAND DOOR

RIGHT HAND DOOR ILLUSTRATED, SAME DIMENSIONS APPLY TO LEFT HAND DOOR

MEASURED FROM HINGE CENTERLINE

DO NOT SCALE DRAWING

9-1/16" (230 mm) "A"

3/4" (19 mm)

3" (76 mm)

STOP FACE

SPEED REGULATING

VALVES

BC VALVE

CENTERLINE

OF HINGE

PA PLATE

FRAME

DOOR

PARALLEL ARM INSTALLATION

MODEL UH4031 or UH4032 INSTALLATION INSTRUCTIONS

PAGE 4

999-30013

50 Icon, Foothill Ranch, CA 92610-3000 USA

www.hamptonproducts.com • 1-800-562-5625

999-30013 REVB_Eng 12/20

FOR CUSTOMER CARE CALL TOLL FREE:

800-562-5625 OR [email protected]

Questo manuale è adatto per i seguenti modelli

Altri manuali UNIVERSAL HARDWARE Serratura della porta

UNIVERSAL HARDWARE

UNIVERSAL HARDWARE UH4051 Manuale utente

Manuali Serratura della porta popolari di altre marche

Assa Abloy

Assa Abloy effeff 827A-IP Manuale utente

We.lock

We.lock SECBNEBL51 Manuale utente

Iseo

Iseo MA1A Manuale utente

ID Lock

ID Lock 150 Manuale utente

Lockly

Lockly ACCESS TOUCH PRO Manuale utente

iLoq

iLoq G50S Manuale utente

SDC

SDC Z7835 Manuale utente

ilco

ilco 452 Manuale utente

Samsung

Samsung shs-h705 Manuale utente

TRU-BOLT

TRU-BOLT 08102017 Manuale utente

CDVI

CDVI 500-LADJ Manuale utente

Igloohome

Igloohome Deadbolt 2S Metal Grey Istruzioni di installazione e manutenzione

eSSL

eSSL FL-300 Manuale utente

JAKO

JAKO JKBTNX4 Manuale utente

Dorma

Dorma MUNDUS PREMIUM GK 50 Guida utente

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuale utente

Yale

Yale MORTISE 8800 SERIES Manuale utente

Siegenia

Siegenia KFV AS3500 Manuale utente