Universal Tool UT8931 Manuale utente

INSTRUCTION MANUAL

Air Auto Shut-Off Straight Screwdrivers

This product is designed for installing and removing threadedfasteners in wood, metal,

and plastic. The use of spare parts/accessories other than those originally supplied by

the manufacturer may result in a drop in performance and/or increased

maintenance/noise level/vibrations, and as the result, the full cancellation of the

manufacturer’s liability. No other use is permitted. For professional use only.

Air Supply Requirements

1. Supply tool with 90 PSI (6.3 KG/CM2) of clean, dry air. Higher pressure drastically

reduces toollife.

2. Connect the tool to the airline using pipe, hose, and fitting sizes shown in the diagram

below.

Lubrication

1. Use an air line lubricator with SAE #10 oil, adjustedtotwo (2) drops per minute.

If an air line lubricator cannot be used, add air motor oil to the inlet once a day.

2. For gearing and clutch, use Shell-grade grease containingmolybdenum.

3. Grease clutches every 12,000 screws.

Torque Adjustment

Shut Off Clutch: Grip the tool around the handle and press the tool into the fixing

which is to be tightened. The motor will start and tighten the fixing to the required

torque set by adjusting the tensions on the clutch spring. At this point, the internal drive

is disengaged and the air to the motor cut off.

1/2" (12mm)

CA048362 (1/2") NPT

CA048361 (1/2") NPT

0 130

1/2" (12mm)

CA048360 (1/2") NPT

1/4 NPT

3/8" (10mm)

10' (3m) MAX

Torque Cover

Air Inlet

R/L Switch

Bit Retainer Sleeve

1234

Operating Procedures

1. Make sure the air in airline is clean and dry.

2. Make sure the tool is connected correctly with the air compressor.

3. Install a bit (as illustrated below). Before using, do check the bit being installed in the

tool correctly.

4. Torque Adjustment: Take off the torque cover and turn the torque adjustment ring

clockwise to increase the torque. Turn the torque adjustment ring counter-clockwise

to reduce the torque. When the torque is set up, put the torque cover back and

fasten it tightly to avoid changing the set-up accidentally. (as illustrated below)

5. Right/Left Indication: Turn right (clockwise) the switch (marked “R”) for tightening

screws. Turn left (counter-clockwise) the switch (marked “L”) for loosening screws.

6. Push to start: Push the tool to activate the motor.

7. Suggestion: Correct / Re-set torques before operation on a daily basis.

8. If not usedfor a long time, re-set the tool to the lowest torque.

Installation of Bit

Press the sleeve softly

Insert a bit

Make sure the bit

is fixed tightly

Set The Torque

R/L Switch

R Indication –turn right (clockwise) –fastening screw

L Indication –turn left (counter-clockwise) –loosening screw

12 3

678

12 3

678

Turn clockwise to

increase the torque

Take off the

adjustment ring

Put the torque

cover back

Fasten the rear

housing

Release the torque cover

Push Softly

Turn counter clockwise

to lower the torque

UT8931 AUTO SHUT-OFF STRAIGHT SCREWDRIVER 1700 RM / 0.3~2.5 NM

INDEX# PARTS NO.

PARTS DESCRIPTION

QTY/

SET

INDEX# PARTS NO.

PARTS DESCRIPTION

QTY/

SET

17120001PS REAR HOUSING 1 41 SPP0208 SPRING PIN 1

27120061PS-W TORQUE COVER 1 42 7120045PS PIN 1

37160002PS C RING 1 43 7120043PS END PLATE 1

47120003PS BIT RETAINER SLEEVE 1 44 7160046PS PIN 1

57120004PS SPRING 2 45 R-1340HH BALL BEARING 1

67120005PS TORQUE RING 1 46 7120048PS VALVE 1

77160006PS REGULATION WASHER 1 47 OR0602 O-RING 1

87120007PS NEEDLE PIN 3 48 7120050PS END HOUSING 1

97120008PS CLUTCH HOUSING 1 49 7120063PS HANDLE GRIP 1

10 7120009PS ANVIL BUSHING 1 50 7160060PS SCREW HOLDER 1

11 7120010PS WASHER 1 51 7160052PS SCREW 1

12 7138011PS TORQUE SPRING 1 52 7120051PS-RD SWITCH 1

13 7160013PS STEEL BALL 1 53 OR2352178 O-RING 1

14 7120012PS ANVIL 1 54 7120054PS OPERATING ROD 1

15 7160014PS STEEL BALL 2 55 OR0302 O-RING 1

16 7120016PS SLIDE BASE 1 56 7160056PS VALVE PLATE 1

17 7120064PS C RING 1 57 7160057PS SPRING 1

18 7120018PS BALL RACE 1 58 7160058PS SILENCER 2

19 7160019PS STEEL BALL 53 59 7120059PS EXHAUST DEFLECTOR 1

20 7120020PS END CLUTCH 1 60 ZZ389507 SILENCER 1

21 7120021PS CENTER CLUTCH 1 61 OR1898 O-RING 1

22 STB3175 STEEL BALL 2 62 7160062PS AIR INLET 1

23 7120023PS REAR CLUTCH 1 63 CP1HP60 HANGER 1

24 7120024PS RETAINER 1

25 7160017PS C RING 1

26 7120025PS PILOT PIN 1

27 B6901ZZ BALL BEARING 1

28 7120027PS CENTER HOUSING 1

29 7120029PS GEAR CAGE 1

30 7120030PS PIN 8

31 7120031PS PLANT GEAR 8

32 7120032PS SUN GEAR 2

33 7150033PS GEAR CAGE 1

34 7120036PS INTERNAL GEAR 1

35 7155066PS RETAINING COLLAR 1

36 L-1680HH HALL BEARING 1

37 7120039PS FRONT PLATE 1

38 7120041PS BLADE 5

39 7138040PS ROTOR 1

40 7120042PS CYLINDER 1

7160064PS

TORQUE ADJUSTMENT

RING

7160080PS

DISTINGUISHABLE RING,

4PC/SET

Division of Florida Pneumatic Mfg Corp.,

851 Jupiter Park Lane,

Jupiter, FL 33458, USA.

Ph: (1) 561 744 9500

Fax: (1) 561 575 5574

EC/UKCA DECLARATION OF CONFORMITY

We FLORIDAPNEUMATICMFGCORP,851JUPITERPARKLANE,JUPITER,FL33458,USA

Declareunderoursoleresponsibilitythatthemachinefallswithintheprovisionsofthe directive:

MachineType: UT8931 AirAutoShut-OffScrewdriver

TechnicalData:

ChuckSize: 1/4”HEXQC FreeSpeed: 1700rpm

Weight: 0.52kg(1.14lbs) Length: 193 mm(7,59”)

RecommendedHoseSize: 10m(3/8”) WorkingAirPressure: 6.3bar(90PSI)

Noise: (soundpressurelevel 72 dB(A) Vibration: 1.81Metres/Sec ²

Spindlesize: N/A Serial No: ________________

Towhichthisdeclarationrelates,isinconformitywiththerequirementsof:TheMachineryDirective2006/42/EC,

GeneralSafetyISO12100:2010,SpecificSafety-ImpactWrenches:ISO11148-6:2012,SpecificVibration- ISO

28927,Noise:ISO15744:2008

Nameandpositionofissuer: TonyLeNeveu:VPEngineering&Development

--------------------------------------------------------------------------------

Indice

Altri manuali Universal Tool Cacciavite elettrico

Universal Tool

Universal Tool UT8960-2 Manuale

Universal Tool

Universal Tool UT8958 Specifiche

Universal Tool

Universal Tool UT8932 Manuale utente

Universal Tool

Universal Tool UT8962-11 Manuale utente

Universal Tool

Universal Tool UT8966 Manuale utente

Universal Tool

Universal Tool UT8963AT-5 Manuale utente

Universal Tool

Universal Tool UT8963 Manuale utente

Universal Tool

Universal Tool UT8963ATT-11 Manuale

Universal Tool

Universal Tool UT8226 Specifiche

Universal Tool

Universal Tool UT8963AT-17 Manuale utente

Universal Tool

Universal Tool UT8906 Specifiche

Universal Tool

Universal Tool UT8963-17 Manuale utente

Universal Tool

Universal Tool UT8955 Specifiche

Universal Tool

Universal Tool UT8963ATT-5 Manuale

Universal Tool

Universal Tool UT8965 Manuale utente

Universal Tool

Universal Tool UT8963AT-11 Manuale utente

Universal Tool

Universal Tool UT8942 Manuale utente

Universal Tool

Universal Tool AINA PTT Specifiche

Universal Tool

Universal Tool UT8818-S Manuale

Universal Tool

Universal Tool UT8955 Manuale utente

Universal Tool

Universal Tool UT8961 Specifiche

Universal Tool

Universal Tool UT2960A Manuale

Universal Tool

Universal Tool UT8943 Manuale utente

Universal Tool

Universal Tool UT8934 Manuale utente

Manuali Cacciavite elettrico popolari di altre marche

Makita

Makita DFT085F Manuale utente

Parkside

Parkside 345138 2004 Manuale utente

Makita

Makita DFL650F Manuale utente

AEG

AEG BST 18BLX2-0 Manuale utente

Ingersoll-Rand

Ingersoll-Rand D5000 Series Manuale utente

BGS technic

BGS technic 956 Manuale utente

Hilti

Hilti SD 6000 Manuale utente

Parkside

Parkside PEPS 3 A1 Manuale utente

Festool

Festool TI 15 Manuale utente

Makita

Makita DWT190 Manuale utente

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Manuale utente

Skil

Skil 2346 Istruzioni per il montaggio

DeWalt

DeWalt XR LI-ION DCD931 Manuale utente

Festool

Festool DWC 18-2500 Manuale utente

EINHELL

EINHELL TE-CD 12/1 Li Series Manuale utente

Makita

Makita BFT043F Manuale utente

Stanley

Stanley SCD2 Manuale utente

Atlas Copco

Atlas Copco LUM12 SR Foglio di istruzioni