uniview technologies Network Video Recorders Manuale utente
Network Video Recorders
Quick Guide
Version: V1.00
BOM: 3101C0FC
1
Thank you for purchasing our product. Contact your local dealer if you have any
questions or feedback. No part of this manual may be copied, reproduced,
translated, or distributed in any form or by any means without prior consent in
writing from our company. Contents of this manual are subject to change without
prior notice. No statement, information, or recommendation in this manual shall
constitute formal guarantee of any kind, expressed or implied.
Safety Information
Read through the instructions carefully before starting installation and operation.
Installation and maintenance must be performed by qualified personnel.
This device is a class A product and may cause radio interference. Take measures if
necessary.
Disconnect power before installation and cable connection. Wear antistatic gloves
during installation. Use the manufacturer recommended battery. Improper use or
replacement of the battery may cause risk of explosion. Dispose of the used
battery according to local regulations or the battery manufacturer's instructions.
Never dispose of the battery in fire.
The device is intended for indoor use only. Ensure a proper operating environment,
including temperature, humidity, ventilation, power supply, and lightning
protection. The device must always be properly grounded. Keep the device from
dust, excessive vibration, liquid of any kind, and strong electromagnetic radiation.
A sudden power failure may cause device damage or loss of data.
Take necessary measures to ensure data security and protect from network attack
and hacking (when connected to Internet).
Regulatory Compliance
FCC Part 15
This equipment has been tested and found to comply with the limits for digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
2
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
This product complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
LVD/EMC Directive
This product complies with the European Low Voltage Directive
2014/35/EU and EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical
& Electronic Equipment (WEEE) Directive and must be disposed of in
a responsible manner.
Default IP, Username and Password
Default IP address: 192.168.1.30
Default admin username: admin
Default admin password: 123456 (only for first login and should be changed to a
strong one with at least 8 characters including upper and lower case letters, digits
and symbols to enhance account security.)
3
Disk Installation
Choose an option. Use a 1# or 2# screwdriver as needed. All photos are only for
illustration.
Option 1 (for 1 or 2 disks)
1. Remove the cover, connect data
and power cables to disk(s), and
then secure disk(s) with screws.
2. Connect data and power cables to the
motherboard and then install the
cover.
Option 2 (for more than 2 disks)
You will open the cover and install hard disks on mounting plate(s).
1. Remove the cover and then
secure disks to mounting
plate(s) with screws.
2. Connect data and power cables to
disks. Secure mounting plate(s) to the
device, and then install the cover.
4
Option 3 (for more than 2 disks)
You will open the front panel and install hard disks on mounting brackets.
1. Secure the disk to a pair of
mounting brackets (L means
left and R means right).
2. Press the latches on both sides (1) and
then detach the front panel (2).
3. Align the disk at the slot and
then insert the disk gently.
4. Push the disk slowly until it clicks.
Repeat the steps to install all disks and
then close the front panel.
Ports, Interfaces and LEDs
The ports, interfaces, connectors, power on/off switch and LED indicators may vary
with device model. See the following two examples.
用螺钉将硬盘固定在拉手条上，拉
手条注意区分左右
用双手分别按住前面板两侧卡扣，
按方向②拆卸前面板
对准硬盘槽位，轻缓、平稳地插入
硬盘
用拇指推进硬盘，可听到扣上的声音，
完成该硬盘安装
5
Power on/off
Audio output
DC power
PoE ports
Audio input
Network
VGA output
HDMI output
USB
Grounding
AC power
USB
Alarm input/output
Power on/off
Grounding
Network
HDMI output
VGA output
Audio out/input RS485
RS232 (for maintenance)
HDMI output
12V DC output
CVBS output
eSATA interface
6
LED
Description
PWR(Power)
Steady on: Connected to power.
RUN(Operation)
Steady on: Normal.
Blinks: Starting up.
NET(Network)
Steady on: Connected to network.
GUARD(Arming)
Steady on: Arming is enabled.
IR
Steady on: Activated for remote control.
Blinks: Authenticating device code.
ALM(Alarm)
Steady on: Device alarm occurred.
CLOUD
Steady on: Connected to cloud.
HD(Hard disk)
One HD LED only:
Steady on: No disk; or disk is abnormal.
Blinks: Reading or writing data.
One HD LED for each disk:
Steady green: Normal.
Blinks green: Reading or writing data.
Steady red: Abnormal.
Blinks red: Rebuilding array.
Startup
Verify installation and cable connection are correct. Connect to power and then turn
on the power on/off switch (if applicable). Follow the wizard to complete the basic
setup after the NVR starts up.
7
Live View
Click Menu > Camera > Camera. The discovered cameras are listed. Click to add
a camera. To search a network segment, click Search. If a camera is added but live
video is not available, check network connection and make sure the correct camera
username and password are set in the system. Modify if necessary.
Playback
Right-click a preview window and then choose Playback to view video recorded on
the current day. A 7×24 recording schedule is enabled at delivery and can be edited
under Menu > Storage > Recording.
Access Using a Web Browser
Access the NVR using a Web browser (e.g., Internet Explorer) from a connected
computer.
1. Enter the NVR's IP address in the address bar and then press Enter. Install the
plugin as prompted. Close all Web browsers when the installation starts.
2. Open the Web browser and log in with the correct username and password.
Shutdown
Use the Shutdown menu instead of by disconnecting power or turning off the
power on/off switch. A sudden power failure may cause device damage and loss of
data.
Indice
Altri manuali uniview technologies Hardware di rete
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
