Uplift Desk FRM072 Manuale utente
Step 1 - Attach the Keypad to Desktop
Most UPLIFT desktops include pre-drilled holes for attaching
a Keypad at the front edge on either side. Choose which side
of the Desktop you would like your Keypad to be on and at-
tach it using the #10x5/8” Wood Screws.
If you do not have an UPLIFT Desktop or choose to place the
Keypad in a different location, hold the Keypad where you
would like to install it and attach it to your desktop using the
two #10x5/8’’ Wood Screws through the two mounting holes.
If you own a drill, you can make this a little easi-
er by drilling pilot holes. Hold the keypad where
you would like to attach it and make a pencil mark
on the desktop in the center of each mounting
hole. Next drill a pilot hole at each pencil mark
using a 1/8” (or 3mm) diameter bit. Note: DRILL
NO DEEPER THAN 1/2”. To ensure this, we recom-
mend wrapping a piece of tape around your drill
bit 1/2” from the tip. Stop drilling just before the
tape touches the desktop. Then attach the Keypad
to the desktop using the #10x5/8” Wood Screws.
Package Contents
Basic Display
Keypad
#10x5/8” Wood Screws
(qty 2)
Basic Display Keypad
FRM072
Step 2 - Install the Cable
Plug the end of the Keypad’s cable into the port marked “HS”
on your UPLIFT Desk control box.
You can use some of the Cable mounts included with your UP-
LIFT Desk frame to organize your Keypad cable and prevent it
from snagging on anything when adjusting the desk’s height.
The Cable mounts work best when stuck directly to one of the
frame’s metal components.
1/2’’
Step 3 - Reset Procedure
If you are installing the Basic Display Keypad on a newly as-
sembled desk, you must rst perform the following Reset Pro-
cedure:
• Press and hold the down button until the desk stops at its
lowest position, then release.
• Press and hold the down button again until the display
reads “ASr”, then release.
• Press and hold the down button one more time until the
desk lowers slightly, rises and stops, then release the but-
ton.
• Once the numeric height is displayed, the reset is com-
plete and the desk is ready for use.
Basic Raising and Lowering
Press and hold the down button to lower the desk. Press and
hold the up button to raise the desk. Release the button to stop
the movement.
Anti-Collision Sensitivity
The Keypad provides access to the Anti-Collision Sensitivity fea-
ture within the desk’s control box. This feature will automatically
stop the desk’s movement if it collides with anything while it is
rising or lowering. You can change this Sensitivity setting by fol-
lowing the steps below.
• Press and hold the down button until the desk stops at its
lowest position, then release the down button.
• Press and hold the down button again until the display reads
“ASr”, then release the down button.
• Press and hold the up button while the display ashes “ASr”
until one of the numbers below shows on the display, then
release the up button. The rst number shown will be the
current sensitivity setting of the desk.
10.5 = 10 kg pressure (most sensitive)
10.6 = 15 kg pressure (moderate sensitivity)
10.7 = 20 kg pressure (least sensitive)
• If this is your preferred sensitivity setting, continue to the
next step to complete the process. Otherwise, press and
hold the up button again to get to the next setting option.
Once the desired sensitivity setting is displayed, continue
to the next step.
• Wait until the display returns to “ASr” then press and hold
the down button one more time until the desk lowers slight-
ly, rises and stops, and the display changes back to the nu-
meric height setting, then release the down button.
Basic Operation & Programming
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may
result in damage or personal injury. Retain manual for future reference.
CAUTIONS & WARNINGS
!
!
If your desk does not respond when you try to raise it or lower it
or if the Keypad displays error messages (“E01” through “E12”),
check to make sure all the cables are secure (cables to the legs
and cables to the control box).
If the problem persists, follow the steps below.
Note: If the desk is unplugged or if you lose power, you may
need to perform the Reset Procedure.
CODE DESCRIPTION TROUBLESHOOTING SOLUTION
H01 Overheated
The desk motor has a 10% duty cycle to protect it from overheating. For
example, in a 20 minute period, if your desk motor is activated for 2 minutes,
you will want to let it rest for 18 minutes. Otherwise you may see an H01
code on your keypad.
E01-E06 Firmware or
connectivity issues
Check all cables to ensure they’re all rmly plugged in, and perform the Re-
set procedure on Page 1, Step 3.
E07-E012 Legs are uneven Perform Reset procedure on Page 1, Step 3.
If the error message persists after performing the Reset Procedure or if there is a height difference between the
legs which exceeds 1.5’’, refer to the Desk Reset + Troubleshooting Steps page at the URL shown below.
https://www.upliftdesk.com/uplift-desk-troubleshooting-and-reset-instructions/
For more troubleshooting information, visit the Desk Reset + Troubleshooting Steps at the URL below.
https://www.upliftdesk.com/uplift-desk-troubleshooting-and-reset-instructions/
Troubleshooting
• Unplug the power cord and press the down button for 30
seconds.
• Plug the power cord back in.
• Perform the Reset Procedure outlined in Step 3 of the in-
stallation instructions.
512-614-3152
800-349-3839
upliftdesk.com
Copyright Notice: This guide is a component of this UPLIFT Desk Product. This guide is a part of the scope of delivery, even if the item is resold. This
guide is also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other
published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
SAVE THESE INSTRUCTIONS
Study this manual carefully. If this desk is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
®
AI-FRM072-1.0
Indice
Altri manuali Uplift Desk Tastiera
