UROVO I6200s Manuale utente

i6200s Quick Guide

Important notice on lithium ion battery

1)Charge the battery only with original Urovo power adaptor supplied

in the box

2)Do not store the device with battery installed for long period of time

3)If long period storage is required, remove battery from device.

4) During long storage period, maintenance work is required at every

3 months period. During maintenance, discharge the battery

completely, and then charge to 60% - 70% (or 3.8V - 3.9V).

5) Store battery in dry, cool environment. Temperature should be -

20 to 40 degree Celsius and relative humidity should be 45% to 85%

6) Charge battery at 5 to 45 degree Celsius

7) Do not operate the device outside the recommended temperature,

which is from -20 to 60.

8) Do not install a third party battery into Urovo device

1）Do not transport the battery at temperature higher than 65 degree

Celsius

2）Do expose battery to fire or heat source

3）Do not forcefully install the battery in opposite direction into the

device

4）Avoid impact and high vibration force on the battery

5）Keep battery dry at all time

6）Do not use battery that is damaged or appear to have been

modified

7）Do not use unauthorized power adaptor to charge the battery

8）Do not discharge the battery beyond the specification of the

battery

9）Do not place battery into microwave oven or pressured container

10）Do not damage battery with sharp objects

11）Do not operate in environment with extreme electrostatic fields

or magnetic fields.

12）If leakage found in battery, avoid contact with body parts.

Should leakage be in contact with body parts, flush with water and

immediately seek medical attention

13）If battery exhibits unusual behavior like color change,

temperature became hot, shape is swollen, remove battery from

device and stop using that battery

14）If the contact point on the battery is dirty, clean with a dry cloth

15）Dispose the battery according local regulation. Recycle if

possible.

16）Improper usage or storage may cause battery performance to

drop, leak, damage, or even escalate to personal safety issue.

Safety precaution

Rear view

Appearance and Buttons

Side view

Front view

To turn on: Hold power button until device switches on

To turn off: Hold power button until the device screen shows the

power off menu. Select shutdown on the menu.

Sleep: Under operation mode, press the power button once

Wake up: Press power button once

Scan button

User define button

LED indicator

Touch screen

Main key pad

Scan engine

window

POGO pin connector

for cradle charging

Power button

Volume control

Reset button

Audio jack

USB connector

Scan button

Camera and LED flash

Speaker

SIM Slot

Battery lock

Micro SD card slot

Contactless reader

PSAM Slot

1 2 34

i6200s Quick Guide

Important notice on lithium ion battery

1)Charge the battery only with original Urovo power adaptor supplied

in the box

2)Do not store the device with battery installed for long period of time

3)If long period storage is required, remove battery from device.

4) During long storage period, maintenance work is required at every

3 months period. During maintenance, discharge the battery

completely, and then charge to 60% - 70% (or 3.8V - 3.9V).

5) Store battery in dry, cool environment. Temperature should be -

20 to 40 degree Celsius and relative humidity should be 45% to 85%

6) Charge battery at 5 to 45 degree Celsius

7) Do not operate the device outside the recommended temperature,

which is from -20 to 60.

8) Do not install a third party battery into Urovo device

1）Do not transport the battery at temperature higher than 65 degree

Celsius

2）Do expose battery to fire or heat source

3）Do not forcefully install the battery in opposite direction into the

device

4）Avoid impact and high vibration force on the battery

5）Keep battery dry at all time

6）Do not use battery that is damaged or appear to have been

modified

7）Do not use unauthorized power adaptor to charge the battery

8）Do not discharge the battery beyond the specification of the

battery

9）Do not place battery into microwave oven or pressured container

10）Do not damage battery with sharp objects

11）Do not operate in environment with extreme electrostatic fields

or magnetic fields.

12）If leakage found in battery, avoid contact with body parts.

Should leakage be in contact with body parts, flush with water and

immediately seek medical attention

13）If battery exhibits unusual behavior like color change,

temperature became hot, shape is swollen, remove battery from

device and stop using that battery

14）If the contact point on the battery is dirty, clean with a dry cloth

15）Dispose the battery according local regulation. Recycle if

possible.

16）Improper usage or storage may cause battery performance to

drop, leak, damage, or even escalate to personal safety issue.

Safety precaution

Rear view

Appearance and Buttons

Side view

Front view

To turn on: Hold power button until device switches on

To turn off: Hold power button until the device screen shows the

power off menu. Select shutdown on the menu.

Sleep: Under operation mode, press the power button once

Wake up: Press power button once

Scan button

User define button

LED indicator

Touch screen

Main key pad

Scan engine

window

POGO pin connector

for cradle charging

Power button

Volume control

Reset button

Audio jack

USB connector

Scan button

Camera and LED flash

Speaker

SIM Slot

Battery lock

Micro SD card slot

Contactless reader

PSAM Slot

1 2 34

i6200s Quick Guide

Important notice on lithium ion battery

1)Charge the battery only with original Urovo power adaptor supplied

in the box

2)Do not store the device with battery installed for long period of time

3)If long period storage is required, remove battery from device.

4) During long storage period, maintenance work is required at every

3 months period. During maintenance, discharge the battery

completely, and then charge to 60% - 70% (or 3.8V - 3.9V).

5) Store battery in dry, cool environment. Temperature should be -

20 to 40 degree Celsius and relative humidity should be 45% to 85%

6) Charge battery at 5 to 45 degree Celsius

7) Do not operate the device outside the recommended temperature,

which is from -20 to 60.

8) Do not install a third party battery into Urovo device

1）Do not transport the battery at temperature higher than 65 degree

Celsius

2）Do expose battery to fire or heat source

3）Do not forcefully install the battery in opposite direction into the

device

4）Avoid impact and high vibration force on the battery

5）Keep battery dry at all time

6）Do not use battery that is damaged or appear to have been

modified

7）Do not use unauthorized power adaptor to charge the battery

8）Do not discharge the battery beyond the specification of the

battery

9）Do not place battery into microwave oven or pressured container

10）Do not damage battery with sharp objects

11）Do not operate in environment with extreme electrostatic fields

or magnetic fields.

12）If leakage found in battery, avoid contact with body parts.

Should leakage be in contact with body parts, flush with water and

immediately seek medical attention

13）If battery exhibits unusual behavior like color change,

temperature became hot, shape is swollen, remove battery from

device and stop using that battery

14）If the contact point on the battery is dirty, clean with a dry cloth

15）Dispose the battery according local regulation. Recycle if

possible.

16）Improper usage or storage may cause battery performance to

drop, leak, damage, or even escalate to personal safety issue.

Safety precaution

Rear view

Appearance and Buttons

Side view

Front view

To turn on: Hold power button until device switches on

To turn off: Hold power button until the device screen shows the

power off menu. Select shutdown on the menu.

Sleep: Under operation mode, press the power button once

Wake up: Press power button once

Scan button

User define button

LED indicator

Touch screen

Main key pad

Scan engine

window

POGO pin connector

for cradle charging

Power button

Volume control

Reset button

Audio jack

USB connector

Scan button

Camera and LED flash

Speaker

SIM Slot

Battery lock

Micro SD card slot

Contactless reader

PSAM Slot

1 2 34

i6200s Quick Guide

Important notice on lithium ion battery

1)Charge the battery only with original Urovo power adaptor supplied

in the box

2)Do not store the device with battery installed for long period of time

3)If long period storage is required, remove battery from device.

4) During long storage period, maintenance work is required at every

3 months period. During maintenance, discharge the battery

completely, and then charge to 60% - 70% (or 3.8V - 3.9V).

5) Store battery in dry, cool environment. Temperature should be -

20 to 40 degree Celsius and relative humidity should be 45% to 85%

6) Charge battery at 5 to 45 degree Celsius

7) Do not operate the device outside the recommended temperature,

which is from -20 to 60.

8) Do not install a third party battery into Urovo device

1）Do not transport the battery at temperature higher than 65 degree

Celsius

2）Do expose battery to fire or heat source

3）Do not forcefully install the battery in opposite direction into the

device

4）Avoid impact and high vibration force on the battery

5）Keep battery dry at all time

6）Do not use battery that is damaged or appear to have been

modified

7）Do not use unauthorized power adaptor to charge the battery

8）Do not discharge the battery beyond the specification of the

battery

9）Do not place battery into microwave oven or pressured container

10）Do not damage battery with sharp objects

11）Do not operate in environment with extreme electrostatic fields

or magnetic fields.

12）If leakage found in battery, avoid contact with body parts.

Should leakage be in contact with body parts, flush with water and

immediately seek medical attention

13）If battery exhibits unusual behavior like color change,

temperature became hot, shape is swollen, remove battery from

device and stop using that battery

14）If the contact point on the battery is dirty, clean with a dry cloth

15）Dispose the battery according local regulation. Recycle if

possible.

16）Improper usage or storage may cause battery performance to

drop, leak, damage, or even escalate to personal safety issue.

Safety precaution

Rear view

Appearance and Buttons

Side view

Front view

To turn on: Hold power button until device switches on

To turn off: Hold power button until the device screen shows the

power off menu. Select shutdown on the menu.

Sleep: Under operation mode, press the power button once

Wake up: Press power button once

Scan button

User define button

LED indicator

Touch screen

Main key pad

Scan engine

window

POGO pin connector

for cradle charging

Power button

Volume control

Reset button

Audio jack

USB connector

Scan button

Camera and LED flash

Speaker

SIM Slot

Battery lock

Micro SD card slot

Contactless reader

PSAM Slot

1 2 34

Battery Installation

The device battery is polymer type battery, which should only be

charged by using original Urovo power supply.

Metal contact is unavailable or artificial short circuit electrode.

Do not store battery in hot, humid, or corrosive environment.

Do no break or crack battery.

Do not store battery when it is fully charged completely drained.

If device is not used for long period of time, remove the battery from

the device, pelase.

If the battery is misshapen or is found leaking, replace the battery

immediately.

Note: The battery should be charged for at least 8 hours before the

first use.

Battery Operation

5 6 8

After the device connected to your PC, you could drag the

top part of the screen downto show the USB options.

Note: When you enable device as USB Storage to PC, the flash

memory of the device are map as a PC drive. At this point of time,

you cannot install APK to the device.

To install APK to the device, it should not be in USB Storage mode.

Check this to enable USB debugging.

Charging using power adaptor

Device Slot

Battery Slot

C Indication light

P Indication light

1.Swing open the main battery

cover clip by 90 degrees, you can

then remove the battery cover.

2.Insert the SIM card or Micro

SD/TF card into their

corresponding slots in the battery

compartment.

Note: You should gently push the

SIM/TF card to the correct position

without using excessive force.

Connect the USB cable into the device and the power adaptor. Red

LED indicates charging and Green LED indicates fully charge.

Power Adaptor

USB Data Cable

Charging using cradle

Connect the power cable into the cradle.

P: LED indicates the cradle is operational.

Slot the device into the cradle and take note of the LED change on

the device which indicate the charging process

Slot the battery into the cradle as shown in the picture.

C: LED should lit up to indicate charging.

Installing SIM/ TF Card

Insert the battery into the battery compartment as shown in the

picture. Battery should sit tightly in the compartment when correctly

installed. Do not apply excessive force when inserting the battery.

Power Adaptor

After you install the Android driver or an Android smart phone

assistant, you can connect the devices to your PC with USB cable

provided. (You can download the software mentioned above from

www.urovo.com/en. After device connected to your PC, the screen

would display like this:

Connecting to PC

Check this to enable device as USB storage to PC.

Select this option to enable / disable device as USB

storage to the PC.

Select this option to enable / disable USB debugging

Battery Installation

The device battery is polymer type battery, which should only be

charged by using original Urovo power supply.

Metal contact is unavailable or artificial short circuit electrode.

Do not store battery in hot, humid, or corrosive environment.

Do no break or crack battery.

Do not store battery when it is fully charged completely drained.

If device is not used for long period of time, remove the battery from

the device, pelase.

If the battery is misshapen or is found leaking, replace the battery

immediately.

Note: The battery should be charged for at least 8 hours before the

first use.

Battery Operation

5 6 8

After the device connected to your PC, you could drag the

top part of the screen downto show the USB options.

Note: When you enable device as USB Storage to PC, the flash

memory of the device are map as a PC drive. At this point of time,

you cannot install APK to the device.

To install APK to the device, it should not be in USB Storage mode.

Check this to enable USB debugging.

Charging using power adaptor

Device Slot

Battery Slot

C Indication light

P Indication light

1.Swing open the main battery

cover clip by 90 degrees, you can

then remove the battery cover.

2.Insert the SIM card or Micro

SD/TF card into their

corresponding slots in the battery

compartment.

Note: You should gently push the

SIM/TF card to the correct position

without using excessive force.

Connect the USB cable into the device and the power adaptor. Red

LED indicates charging and Green LED indicates fully charge.

Power Adaptor

USB Data Cable

Charging using cradle

Connect the power cable into the cradle.

P: LED indicates the cradle is operational.

Slot the device into the cradle and take note of the LED change on

the device which indicate the charging process

Slot the battery into the cradle as shown in the picture.

C: LED should lit up to indicate charging.

Installing SIM/ TF Card

Insert the battery into the battery compartment as shown in the

picture. Battery should sit tightly in the compartment when correctly

installed. Do not apply excessive force when inserting the battery.

Power Adaptor

After you install the Android driver or an Android smart phone

assistant, you can connect the devices to your PC with USB cable

provided. (You can download the software mentioned above from

www.urovo.com/en. After device connected to your PC, the screen

would display like this:

Connecting to PC

Check this to enable device as USB storage to PC.

Select this option to enable / disable device as USB

storage to the PC.

Select this option to enable / disable USB debugging

Battery Installation

The device battery is polymer type battery, which should only be

charged by using original Urovo power supply.

Metal contact is unavailable or artificial short circuit electrode.

Do not store battery in hot, humid, or corrosive environment.

Do no break or crack battery.

Do not store battery when it is fully charged completely drained.

If device is not used for long period of time, remove the battery from

the device, pelase.

If the battery is misshapen or is found leaking, replace the battery

immediately.

Note: The battery should be charged for at least 8 hours before the

first use.

Battery Operation

5 6 8

After the device connected to your PC, you could drag the

top part of the screen downto show the USB options.

Note: When you enable device as USB Storage to PC, the flash

memory of the device are map as a PC drive. At this point of time,

you cannot install APK to the device.

To install APK to the device, it should not be in USB Storage mode.

Check this to enable USB debugging.

Charging using power adaptor

Device Slot

Battery Slot

C Indication light

P Indication light

1.Swing open the main battery

cover clip by 90 degrees, you can

then remove the battery cover.

2.Insert the SIM card or Micro

SD/TF card into their

corresponding slots in the battery

compartment.

Note: You should gently push the

SIM/TF card to the correct position

without using excessive force.

Connect the USB cable into the device and the power adaptor. Red

LED indicates charging and Green LED indicates fully charge.

Power Adaptor

USB Data Cable

Charging using cradle

Connect the power cable into the cradle.

P: LED indicates the cradle is operational.

Slot the device into the cradle and take note of the LED change on

the device which indicate the charging process

Slot the battery into the cradle as shown in the picture.

C: LED should lit up to indicate charging.

Installing SIM/ TF Card

Insert the battery into the battery compartment as shown in the

picture. Battery should sit tightly in the compartment when correctly

installed. Do not apply excessive force when inserting the battery.

Power Adaptor

After you install the Android driver or an Android smart phone

assistant, you can connect the devices to your PC with USB cable

provided. (You can download the software mentioned above from

www.urovo.com/en. After device connected to your PC, the screen

would display like this:

Connecting to PC

Check this to enable device as USB storage to PC.

Select this option to enable / disable device as USB

storage to the PC.

Select this option to enable / disable USB debugging

Battery Installation

The device battery is polymer type battery, which should only be

charged by using original Urovo power supply.

Metal contact is unavailable or artificial short circuit electrode.

Do not store battery in hot, humid, or corrosive environment.

Do no break or crack battery.

Do not store battery when it is fully charged completely drained.

If device is not used for long period of time, remove the battery from

the device, pelase.

If the battery is misshapen or is found leaking, replace the battery

immediately.

Note: The battery should be charged for at least 8 hours before the

first use.

Battery Operation

5 6 8

After the device connected to your PC, you could drag the

top part of the screen downto show the USB options.

Note: When you enable device as USB Storage to PC, the flash

memory of the device are map as a PC drive. At this point of time,

you cannot install APK to the device.

To install APK to the device, it should not be in USB Storage mode.

Check this to enable USB debugging.

Charging using power adaptor

Device Slot

Battery Slot

C Indication light

P Indication light

1.Swing open the main battery

cover clip by 90 degrees, you can

then remove the battery cover.

2.Insert the SIM card or Micro

SD/TF card into their

corresponding slots in the battery

compartment.

Note: You should gently push the

SIM/TF card to the correct position

without using excessive force.

Connect the USB cable into the device and the power adaptor. Red

LED indicates charging and Green LED indicates fully charge.

Power Adaptor

USB Data Cable

Charging using cradle

Connect the power cable into the cradle.

P: LED indicates the cradle is operational.

Slot the device into the cradle and take note of the LED change on

the device which indicate the charging process

Slot the battery into the cradle as shown in the picture.

C: LED should lit up to indicate charging.

Installing SIM/ TF Card

Insert the battery into the battery compartment as shown in the

picture. Battery should sit tightly in the compartment when correctly

installed. Do not apply excessive force when inserting the battery.

Power Adaptor

After you install the Android driver or an Android smart phone

assistant, you can connect the devices to your PC with USB cable

provided. (You can download the software mentioned above from

www.urovo.com/en. After device connected to your PC, the screen

would display like this:

Connecting to PC

Check this to enable device as USB storage to PC.

Select this option to enable / disable device as USB

storage to the PC.

Select this option to enable / disable USB debugging

Indice

Altri manuali UROVO Telefono cellulare

UROVO

UROVO DT50S Manuale utente

Manuali Telefono cellulare popolari di altre marche

Zte

Zte BLADE A520 Manuale utente

Nokia

Nokia Lumia 620 Manuale utente

Blackbe;rry

Blackbe;rry KEYone Manuale utente

Bea-fon

Bea-fon X5 Premium Manuale utente

Blackbe;rry

Blackbe;rry 8707 Series Manuale utente

Blackbe;rry

Blackbe;rry Storm Istruzioni operative

LG LM-X420QN Manuale utente

LifeWatch

LifeWatch V Manuale utente

Bea-fon

Bea-fon SILVER LINE SL860 Manuale utente

IKI Mobile

IKI Mobile KF4.5i Manuale utente

Hitech

Hitech HT-850 Manuale utente

Yezz

Yezz Fashion F10 Manuale utente

Point Mobile

Point Mobile PM60 Manuale utente

Blackbe;rry

Blackbe;rry Q10 Manuale utente

Blackbe;rry

Blackbe;rry Bold 9900 Manuale utente

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manuale utente

LG LM-K420EMW Manuale utente

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manuale utente

UROVO i6200s Manuale utente

Manuali Telefono cellulare popolari di altre marche