Ursalink UR 51 Manuale utente
1
UR51
Industrial Cellular Router
Quick Start Guide
Ursalink Technology Co., Ltd.
www.ursalink.com
1
Welcome
Thank you for choosing Ursalink UR51 industrial cellular router.
This guide describes how to install the UR51 and how to log in the Web GUI to configure the device. Once
you complete the installation, refer to the Ursalink UR51 User Manual for instructions on how to perform
configurations on the device.
Related Documents
This Start Guide only explains the installation of Ursalink UR51 router. For more functionality and advanced
settings, please refer to the relevant documents as below.
Document
Description
Ursalink UR51 Datasheet
Datasheet for the Ursalink UR51 industrial cellular router.
Ursalink UR51 User Guide
Users could refer to the guide for instruction on how to log in the
Web GUI, and how to configure all the settings.
The related documents are available on Ursalink website: http://www.ursalink.com.
Declaration of Conformity
Ursalink UR51 is in conformity with the essential requirements and other relevant provisions of the CE, FCC,
and RoHS.
For assistance, please contact
Ursalink technical support:
Email: support@ursalink.com
Tel: 86-592-5023060
Fax: 86-592-5023065
Ursalink UR51 Quick Start Guide
www.ursalink.com
2
Before you begin to install the UR51 router, please check the package contents to verify that you have
received the items below.
1.1 Package Contents
1 × UR51 Router
1 × Ethernet Cable
1 × Power Adapter
2 × SIM Card Slots
1 × 2-Pin Pluggable
Terminal
1 × Warranty Card
2 × Magnetic Mount
Cellular Antennas
(Default)
2 × Stubby Cellular
Antennas (Optional)
If any of the above items is missing or damaged, please contact your Ursalink sales
Representative.
1 × Stubby Wi-Fi
Antenna (Optional)
1 × GPS Antenna
(Optional)
1 × Wall Mounting Bracket
(Default)
1 × DIN Rail Kit
(Optional)
1 × DB9 Male to Terminal
Block Adapter (Optional)
1. Packing List
Ursalink UR51 Quick Start Guide
www.ursalink.com
3
2.1 Overview
A. Front Panel
B. Rear Panel
2.2 Dimensions (mm)
2. Hardware Introduction
1Main Cellular Antenna Connector
2Micro SD Card Interface
3LED Indicator Area
POWER: Power Indicator
STATUS: Status Indicator
: Signal Strength Indicator
VPN: VPN Indicator
SIM1: SIM1 Status Indicator
SIM2: SIM2 Status Indicator
WLAN: Wi-Fi Indicator
4SIM Card Slot 1 & SIM Card Slot 2
5AUX Cellular Antenna Connector
6Wi-Fi Antenna
1Grounding Stud
2Power Connector
3Ethernet Port Indicator
4Serial Port: RS232 or RS485
5Reset Button
6GPS Antenna Connector
Ursalink UR51 Quick Start Guide
www.ursalink.com
4
2.3 Pinouts
2.4 LED Indicators
LED
Indication
Status
Description
POWER
Power Status
Off
The power is switched off
On
The power is switched on
STATUS
System Status
Red Light
The system goes wrong
Green Light
Static: Start-up
Blinking slowly: the system is running properly
VPN
VPN Status
Off
VPN is disconnected
Green Light
VPN is connected
WLAN (Wi-Fi)
WLAN Status
Off
Wi-Fi is disabled
Green Light
Static: Wi-Fi is enabled
Blinking slowly: sending or receiving data via Wi-Fi
SIM1/SIM2
SIM Card Status
Off
SIM1 or SIM2 is registering or fails to register (or there
are no SIM cards inserted)
Green Light
Blinking slowly: SIM1 or SIM2 has been registered and
is ready for dial-up
Blinking rapidly: SIM1 or SIM2 has been registered and
is dialing up now
Static: SIM1 or SIM2 has been registered and dialed up
successfully
Signal strength
Signal 1/2/3
Off
No signal
Green Light
Static/Off/Off: weak signals with 1-10 ASU (please
check if the antenna is installed correctly, or move the
antenna to a suitable location to get better signal)
PIN
RS232
RS485
Description
1
---
A
Data +
2
RXD
---
Receive Data
3
TXD
---
Transmit Data
4
---
---
---
5
GND
---
Ground
6
---
B
Data -
7
---
---
---
8
---
---
---
9
---
---
---
PIN
Description
10
Positive
11
Negative
Ursalink UR51 Quick Start Guide
www.ursalink.com
5
Static/Static/Off: normal signals with 11-20 ASU
(average signal strength)
Static/Static/Static: strong signals with 21-31 ASU
(signal is good)
2.5 Reset Button
Function
Description
STATUS LED
Action
Reboot
Blinking
Press and hold the reset button for about 5-15 seconds.
Static Green
Release the button and wait for system to reboot.
Reset
Blinking
Press and hold the reset button for more than 15 seconds.
Static Green →
Rapidly Blinking
Release the button and wait.
Off → Blinking
The router is now reset to factory defaults.
2.6 Ethernet Port Indicator
Indicator
Status
Description
Link Indicator (Orange)
Off
Disconnected
Blinking
Transmitting data
On
Connected
Ursalink UR51 Quick Start Guide
www.ursalink.com
6
Environmental Requirements
- Power Input: 9-48 VDC (For UR51: 48 V Power Input is Needed for 802.3af PoE Output )
- Power Consumption: Typical 1.3 W, max 2.8 W (In Non-PoE mode)
- Operating Temperature: -40°C to 70°C (-40°F -158°F)
- Relative Humidity: 0% to 95% (non-condensing) at 25°C/77°F
3.1 SIM Card/Micro SD Card Installation
3.1.1 SIM Card Installation
A. Push the yellow button on the front panel of the B. Put SIM card onto the slot then insert the
slot router, and then you will see the SIM card back into the hole.
slot popping out directly.
3.1.2 Micro SD Card Installation
Insert Micro SD card
3. Hardware Installation
Ursalink UR51 Quick Start Guide
www.ursalink.com
7
3.2 Antenna Installation
Rotate the antenna into the antenna connector accordingly.
The external cellular antenna should be installed vertically always on a site with a good cellular signal.
3.3 Connect the Router to a Computer
3.4 Mount the Router
The router can be placed on a desktop or mounted to a wall or a DIN rail.
3.4.1 Wall Mounting (Measured in mm)
Use 2 pcs of M3 ×6 flat head Phillips screws to fix the wall mounting kit to the router, and then use 2 pcs of
M3 drywall screws to mount the router associated with the wall mounting kit on the wall.
Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.
Ursalink UR51 Quick Start Guide
www.ursalink.com
8
3.4.2 DIN Rail Mounting (Measured in mm)
Use 2 pcs of M3 ×6 flat head Phillips screws to fix the DIN rail to the router, and then hang the DIN rail on
the mounting bracket. It is necessary to choose a standard bracket.
Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.
3.5 Power Supply Installation
A. Take out the terminal from the router and unscrew the bolt on terminal
B. Screw down the bolt after inserting power cable into the terminal
If the wires are inserted into the reverse holes, the router will not start and the user must switch the
wires into the correct holes.
3.6 Protective Grounding Installation
A. Remove the grounding nut.
B. Connect the grounding ring of the cabinet’s grounding wire onto the grounding stud and screw up the
grounding nut.
The router must be grounded when deployed. According to operating environment, the ground wire
should be connected with grounding stud of router.
Color
Polarity
Red
+
Yellow
-
Connecting the Power Cable
Ursalink UR51 Quick Start Guide
www.ursalink.com
9
Getting Started
Please connect PC to FE port of UR51 router directly. PC can obtain an IP address, or you can configure a
static IP address manually. The following steps are based on Windows 10 operating system for your
reference.
③Click “Ethernet” (May have different names). ④Click “Properties”.
4. PC Configuration for Web GUI Accessing to Router
①Click “Search Box” to search “Control Panel” on the
Windows 10 taskbar.
②Click “Control Panel” to open it, and then
click “View network status and tasks”.
Altri manuali per UR 51
1
Indice
Altri manuali Ursalink Router di rete
Ursalink
Ursalink UR35 Manuale utente
Ursalink
Ursalink UR32 Manuale utente
Ursalink
Ursalink UR32 Manuale utente
Ursalink
Ursalink UR75 Edge Manuale utente
Ursalink
Ursalink UR55 Manuale utente
Ursalink
Ursalink UR75 Edge Manuale utente
Ursalink
Ursalink UR 51 Manuale utente
Ursalink
Ursalink UR52 Manuale utente
Ursalink
Ursalink UR75 Edge Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza