
vii
Figure 1. M3000 controller and components assembly drawing - wall mounting................................................................12
Figure 2. Typical installation using shielded cable/drain wire - outside and inside the enclosure................................13
Figure 3. Earth Ground Connection..............................................................................................................................................................14
Figure 4. M3000 controller - rack mounting ............................................................................................................................................16
Figure 5. Power/Communications board layout....................................................................................................................................18
Figure 6. Wiring AC power through the terminal block ......................................................................................................................20
Figure 7. Fuse location on the Power/Communications board .....................................................................................................21
Figure 8. Wiring diagram for the battery backup, AC power fail, and low battery................................................................23
Figure 9. Wiring host computer to first M3000.......................................................................................................................................27
Figure 10. Wiring host computer to modem or serial printer.............................................................................................................28
Figure 11. Wiring modem to M3000, M/5 or serial printer...................................................................................................................29
Figure 12. Wiring upstream (toward the host) using RS-232 .............................................................................................................30
Figure 13. Wiring downstream (away from the host) using RS-232 ..............................................................................................31
Figure 14. Wiring upstream (toward the host) using RS-422..............................................................................................................32
Figure 15. Wiring downstream (away from the host) using RS-422................................................................................................33
Figure 16. PXNplus CPU board layout............................................................................................................................................................37
Figure 17. 2RP reader board layout................................................................................................................................................................48
Figure 18. Setting 2RP reader voltage...........................................................................................................................................................51
Figure 19. Installing 2RP resistor packs ........................................................................................................................................................52
Figure 20. 2RP reader connector points.......................................................................................................................................................54
Figure 21. Wiring 2RP to Wiegand, Strobed, F/2F, and supervised F/2F readers......................................................................55
Figure 22. Wiring 2RP exit request and door alarm contact...............................................................................................................56
Figure 23. Wiring 2RP door strike - internal relay.....................................................................................................................................57
Figure 24. Wiring 2RP door strike - external relay ...................................................................................................................................58
Figure 25. Wiring 2RP auxiliary DO relay......................................................................................................................................................59
Figure 26. Wiring 2RP external alarm shunt relay...................................................................................................................................60
Figure 27. 2SRP supervised reader board layout.....................................................................................................................................62
Figure 28. Setting 2SRP reader voltage ........................................................................................................................................................65
Figure 29. Installing 2SRP resistor packs......................................................................................................................................................66
Figure 30. Wiring 2SRP to Wiegand, F/2F, Strobed, and Supervised F/2F Readers..................................................................68
Figure 17. 2SRP supervised reader connector points ............................................................................................................................69
Figure 18. Wiring 2SRP to single color LED reader ..................................................................................................................................70
Figure 19. Wiring 2SRP door alarm contact and exit request............................................................................................................72
Figure 20. Wiring 2SRP door strike - internal relay..................................................................................................................................73
Figure 21. Wiring 2SRP door strike - external relay.................................................................................................................................74
Figure 22. Wiring 2SRP auxiliary DO relay ...................................................................................................................................................75
Figure 23. Wiring 2SRP external alarm shunt relay.................................................................................................................................76
Figure 24. 8RP reader board layout................................................................................................................................................................79
Figure 25. Powering two 8RP boards.............................................................................................................................................................80
Figure 26. Wiring 8RP to F/2F or Supervised F/2F Readers.................................................................................................................82
Figure 27. Wiring 8RP door strike - external relay ...................................................................................................................................83
Figure 31. 20DI board layout .............................................................................................................................................................................87
Figure 32. Wiring DI point....................................................................................................................................................................................89
Figure 33. 16DO board layout ...........................................................................................................................................................................91
Figure 34. 16DOR board layout ........................................................................................................................................................................92
Figure 35. Wiring output device to 16DO board.......................................................................................................................................93
Figure 36. Wiring output device to 16DOR board ....................................................................................................................................94
Figure 37. Connecting directly using crossover cable...........................................................................................................................98
Figure 38. Connecting through network hub.............................................................................................................................................99
Figure 39. Saving changes in the Integrated Configuration Tool..................................................................................................103
Figure 40. Host/Connection type form.......................................................................................................................................................104
Figure 41. Controller Information form......................................................................................................................................................105