Utilitech 148003 Manuale utente

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

Altri manuali per 148003

Indice

Altri manuali Utilitech Pompa dell'acqua

Utilitech

Utilitech 148012 Manuale utente

Utilitech

Utilitech UT100USP Manuale utente

Utilitech

Utilitech PPTP1 Manuale utente

Utilitech

Utilitech UT2100IGPP Manuale utente

Utilitech

Utilitech 50AC-110N Manuale utente

Utilitech

Utilitech 148007 Manuale utente

Utilitech

Utilitech 148013 Manuale utente

Utilitech

Utilitech UT25PCP Manuale utente

Utilitech

Utilitech PPWF50 Manuale utente

Utilitech

Utilitech PPTPC50 Manuale utente

Utilitech

Utilitech 148008 Manuale utente

Utilitech

Utilitech #PPLSP100-SS Manuale utente

Utilitech

Utilitech 148003 Manuale utente

Utilitech

Utilitech EFCWJ10-L Manuale utente

Utilitech

Utilitech 50AC-110 Manuale

Utilitech

Utilitech 148008 Manuale utente

Utilitech

Utilitech PPSU33 Manuale utente

Utilitech

Utilitech PPWB Manuale utente

Utilitech

Utilitech 148137 Manuale utente

Utilitech

Utilitech 148003 Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente