UWE DM-3000 Manuale utente

DM SERIES

ELECTRONIC WEIGHING SCALE

OPERATION MANUAL

PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE

ATTEMPT TO OPERATE THE SCALE

FEBRUARY 2002

Specifications subject to change without prior notice

CONTENTS

CAUTIONS

1. INSTALLATION

2. SPECIFICATIONS

3. KEYBOARD LAYOUT AND DESCRIPTION

4. INITIAL SETUP

5. INSTRUCTION FOR USE

6. TROUBLE SHOOTING

7. DAILY CARE AND MAINTENANCE

CAUTIONS

1. This unit is legal for trade only when it

is sealed (and/or stamped) and bearing a

serial number. Do not attempt to break the

seal (or stamp) affixed to this scale or

remove the serial number. Contact your

dealer for more information and after sales

service.

2. For most accurate weighing result, do not

use this scale in where or when the

environment condition falls beyond as those

listed on SPECIFICATIONS.

3. Do not attempt to open this unit or conduct

any trouble shootings other than those

listed on TROUBLE SHOOTING.

4. Do not submerge scale into water.

5. Do not use pressurized water nozzle for

cleaning.

Do not use this scale for chemical substances

or in any environment that contains chemical

vapor.

6. Precision measuring instrument, handle with

care.

7. Always apply the rubber cap (FIG 2 E) when

not in charging.

8. Do not attempt to open scale.

1. INSTALLATION

1.1 Check and make sure that the following

accessories are included:

This operation manual

Scale x 1

Plastic platter x 1

Stainless steel cover x 1

Power adaptor x 1

Contact your dealer if any item missed.

FIG 1

FIG 2

1.2 Locks the plastic platter (FIG 1 A) to the

platter holder, with the screw (FIG 1 B)

included, and then apply the rubber cap

(FIG 1 C).

1.3 Place the stainless steel platter (FIG 1

D) onto the plastic platter.

1.4 Power on the scale

a. Before plugging the power adaptor into

electricity outlet, check and make sure

that the input voltage of power adaptor

matches with the output voltage of the

outlet. If not, do not plug in and contact

your dealer immediately.

b. Before first time use, plug the adaptor

into the wall outlet and charge the scale

for at least 8 hours.

c. After battery is fully recharged, remove

adaptor from scale. Apply the rubber cap

(FIG 2 E) to seal the DC input jack of

scale.

2. SPECIFICATIONS

Model No. Capacity

Division

Accuracy

Min.Load

DM-3000 3000g 1g 1/3000 20g

DM-6000 6000g 2g 1/3000 40g

DM-15K 15kg 0.005kg 1/3000 0.1g

DM-30K 30kg 0.01kg 1/3000 0.2g

DM-1100 1100g 0.1g 1/11000 2g

DM-11K 11kg 1g 1/11000 20g

Tare Range Full tare range (Subtractive)

Display 5 x 24mm LCD display

Operation

Environment

0o~40oC (32o~104oF),

Non-condensed. R.H.¡Ø85%

Powersource

By Built-

in rechargeable battery or power

adaptor

Specifications subject to change without notice

NOTE

To comply with the law of certain countries

and certain approval requirements, the

imperial weight units may be disabled. Contact

your dealer for more information.

3. KEYBOARD LAYOUT AND DESCRIPTION

1. ON/ZERO KEY

Press this key to: (a) turn scale on or reset

display value to zero during normal

operation, (b) return to normal operation

during function setup

2. TARE KEY

Press this key to tare off the weight of

a container during normal operation.

3. MODE KEY

Press this key to shift among different

weight units and display parameters.

4. OFF KEY

Press this key to turn scale off.

5. ZERO INDICATOR

This indicator appears to indicate a zero

weight status.

6. TARE INDICATOR

This indicator appears to indicate the tare

function is in operation and weight

displayed is net weight.

7. WEIGHT UNIT INDICATOR

This indicator appears to indicate the

weighing unit being selected is at metric.

8. LO-BAT INDICATOR

When this indicator appears, recharge the

scale immediately. Failure to do so may

cause unrecoverable damage to the

rechargeable battery inside scale.

9. IN-CHARGE INDICATOR

Red color: Recharging battery

Green color: Charging completed

10.WEIGHT UNIT INDICATOR

This indicator appears to indicate the

weighing unit being selected. Two

avoirdupois weight units are available and

this indicator means the weighing unit is

at decimal pound (e.g. 5.62 means 5.62 lb).

11.WEIGHT UNIT INDICATOR

This indicator appears to indicate the

weighing unit being selected is at

pound/ounce (e.g. 2.15.1 means 2 lb and 15.1

ounce).

4. INITIAL SETUP

4.1 PLACING THE SCALE

In order to obtain an accurate weighing result,

the scale must be placed on a strong and level

surface.

If required, adjust the adjustable feet (FIG

2 F) underneath scale to obtain a level position.

Refer to the bubble indicator for leveling

condition.

4.2 INTERNAL SETTING

4.2.1 Select Weight Unit and Display Resolution

The scale is equipped with metric and

avoirdupois weight units. Default setting =

metric weight unit only. Follow the below steps

to enable/disable the avoirdupois units.

Turn scale off

a. Press and hold TARE, then press ON/ZERO

b. Scale displays F.1

c. Press TARE twice

d. Scale displays F.3

e. Press and hold MODE for 3 second and then

release.

f. Press MODE to shift between desired

configurations appears.

g. Press ON/ZERO to confirm and return to

normal operation.

NOTE

To comply with the law of certain countries

and certain approval requirements, the

avoirdupois weight units may be disabled.

Contact your dealer for more information.

4.2.2 Select Auto Power Off Setting

The scale is equipped with Auto Power Off

Function. The scale will be turned off

automatically if it is not used for 4 minutes.

Follow the below steps to enable/disable

Auto Power Off Function

a. Turn scale off

b. Press and hold TARE, then press ON/ZERO

c. Scale displays F.1

d. Press TARE three times

e. Scale displays F.4

f. Press MODE to shift between 0._OFF and

4._OFF.

g. To enable Auto Power Off Function, press

ON/ZERO when 4._OFF appears.

h. To disable AutoPowerOffFunction, press

ON/ZERO when 0._OFF appears.

i. Press ON/ZERO to confirm and return to

normal operation.

4.3 SELECT BAUD RATE SETTING

This scale equipped with 6 RS232C output baud

rate settings for user to choose the desire

print transmission speed. Default setting =

9600.

Follow the below steps to select baud rate.

a. Turn scale off

b. Press and hold TARE, then press ON/ZERO

c. Scale displays F.1

d. Press TARE four times

e. Scale displays F.5

f. Press MODE to select baud rate of 1200,

2400,4800, 9600, 19200, 38400.

g. Press ON/ZERO to confirm and return to

normal operation.

Note:

No transmission will be activated if weight

detected is less than 20e.

The default data output format of the scale

Baud Rate = 9600

Data Bit = 8

Stop Bit = 1

Parity = None

5. INSTRUCTION FOR USE

5.1 BEFORE WEIGHING

Make sure that:

a. The plastic platter is screwed firmly and

the stainless steel platter cover is placed

on the plastic platter.

b. The scale is placed on a level and strong

surface.

c. The scale is turned on.

d. The ZERO INDICATOR is on. If not, press

ZERO/ON to set display to zero.

5.2 WEIGHING

a. Always place an object onto the platter

gently. Excessive force applied to platter

may cause damages to sensor inside scale.

b. The weight of the object would be displayed

automatically.

c. It is a good practice to remove all loads

from platter after weighing. It would

prolong the lifetime of scale.

5.3 SELECT WEIGHT UNIT

Press MODE to shift among kg àdecimal lb à

lb/oz. àkg weight units. Refer to 4.2.1 for

internal setting procedures.

The weight unit used before power off would

be employed when the scale is turned on again.

5.4 SMART POWER SAVING FUNCTION

When this function is enable, the backlight

will be turned off when constant/zero weight

is detected and remains stable for about 10/3

seconds.

Backlight will be automatically turned on again

when a weight is detected.

5.5 SET DISPLAYED VALUE TO ZERO WHEN UNLOADED

Pressing the ON/ZERO can eliminate a positive

or negative value. After the ON/ZERO is pressed,

the ZERO INDICATOR appears.

Refer to SPECIFICATIONSfor maximum zero range.

5.6 TARE OFF THE WEIGHT OF A CONTAINER

When a container is used, follow the below steps

to tare off the weight of the container and

get the net weight.

a. Remove all loads away from platter

b. Make sure that the ZERO INDICATOR is on.

c. Place the container on the platter.

d. Press TARE.

After TARE is pressed, the TARE INDICATOR would

appear.

Refer to 5.2 for weighing procedures. Weight

displayed under is the net weight of the subject

matter. Refer to SPECIFICATIONS for maximum

tare range.

5.7 CLEAR THE TARE FUNCTION

Remove all loads from platter then press TARE.

After TARE is pressed, the TARE INDICATOR would

disappear.

5.8 RECHARGE THE SCALE

The scale is equipped with a built-in

rechargeable battery. When the LO-BAT

INDICATOR appears, recharge the scale

immediately. Failure to do so may cause

unrecoverable damage to the rechargeable

battery.

Charging is completed when the color of the

IN-CHARGE INDICATOR turns to green.

6. TROUBLE SHOOTING

Syndrome Scale cannot be turned on

Check: Is the scale charged?

Action: Recharge the scale for at least 8

hours before first time use or plug

in the power adaptor before power

on the scale.

Check Is the power adaptor inserted

properly into both the electricity

outlet and the DC inlet of scale.

Action: Secure both ends of the power adaptor

and try again.

Syndrome Scale turned off automatically

Check Is Auto Power Off Function employed?

Action Refer to 4.2.2 to disable Auto Power

Off Function.

Check Is the LO-BAT INDICATOR on?

Action Apply the power adaptor.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Scala popolari di altre marche

AWS

AWS ZEO-50 Manuale utente

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

Rice Lake

Rice Lake MSI-4260 IS Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente