Valor 590FVK2 Manuale utente

Application

This kit is intended to be used when installing one of the

listed models into an existing solid-fuel burning fireplace

and the existing chimney is too small for installing side-

by-side 3” co-linear liners. The outer diameter of the

590FVK2 liner is approximately 5-3/8”.

A separate flue collar adapter is required for each listed

fireplace model to convert the collars to the 590FVK2’s

5” x 3” liner size. The 590FVK2 kit includes an adapter

with flashing for the top of the chimney that converts to

6-5/8” x 4” collars to accept standard listed Coaxial Vent

Temination Caps.

Use the included gear clamps and sheet metal screws to

secure the liners to the collars at the top and bottom of

liners. See following pages for more information.

DO NOT overstretch the flex—stretch it only to the

length required.

DO NOT squeeze, kink, tear or make flex liners oval.

DO NOT bend flex liners tighter than 5” radius.

DO NOT splice flex liners.

DO NOT use flex liners in combustible construction.

4008497-01

590FVK2 Flex Vent Kit

INSTALLER: Leave this manual with the

appliance.

CONSUMER: Retain this manual for

future reference.

INSTALLATION MANUAL

590FVK2

Use with following Valor Models:

- 530INI/IPI Portrain Insert with Co-Axial Vent Plate 530CVA2 ONLY

- RF24JDN/JDP Retrofire Insert with Co-Axial Vent Plate RA24CA ONLY

- 1000KN/KP H3 as an insert with Co-Axial Vent Adapter 1000CAA ONLY

Note

This kit must be installed or serviced by

a qualified installer, service agency or

gas supplier. These instructions are to

be used in conjunction with the main

installation instructions for the above

listed heater model.

WARNING

If the information in these instructions

is not followed exactly, a fire or

explosion may result causing property

damage, personal injury or loss of life.

WARNING

This kit may ONLY be installed in an

existing solid-fuel burning fireplace

and chimney constructed of non-

combustible materials.

3” Flex pipe in

5” Flex pipe

Max. length: 40’ (12.2 m)

Gear clamps

Terminal Adapter

with Flashing

18”

5”

3”

6-5/8” x 4” collars

Kit Content Clean Fireplace and Chimney

Have the chimney swept and the fireplace cavity

including ash dumps and clean-outs cleaned before

installing the heater and vent liners. Any creosote or

soot residue remaining in the fireplace cavity chimney

or clean-out may cause odors or stains once the insert

is installed. Consult with chimney sweep for information

on how best to clean.

Description Part Numbers

Co-axial Terminal Adapter with Flashing 590CVA2

3 x 5 Flex Liner Kit, incl. 2 gear clamps/ﬂex 4006254

18”

Overview—with 530INI/IPI Insert and 530CVA2 Co-axial Vent Adapter Plate

Add optional 530CVA2 for co-axial venting (5” x

3” diameter liners)

Rear view

Add 530CVA2—

Appliance

Adapter

Discard

existing

vent plate

Approved

6-5/8 x 4 co-axial

terminal

- sold separately.

See appliance

manual for listed

terminals

Terminal adapter with

ashing supplied

with 590FVK2

25-1/2”

5” min.

bend radius

5 x 3”

liners

590FVK2

5 x 3” co-axial

liner kit

530CVA2

co-axial

appliance

adapter

530

insert

engine

40’

max

10’

min

Approved 6-5/8 x 4

co-axial terminal

Co-axial installation into existing F/P

530INI/IPI with 530CVA2—Co-axial Appliance

Adapter

Terminal Adapter

with

Flashing supplied

with 590FVK2

Convert to Co-Axial

Venting options

Overview—with RF24JD and RA24CA Co-axial Vent Plate

Rear view Approved 6-5/8 x 4

co-axial terminal

- sold separately. See

appliance manual for

listed terminals

21-1/4”

5” min.

bend radius

5 x 3”

liners

590FVK2

5 x 3” co-axial

liner kit

RA24CA

co-axial

vent plate

RF24JD

insert

engine

40’

max

8’

min

Terminal adapter with

ashing supplied

with 590FVK2

Approved 6-5/8 x 4

co-axial terminal

Co-axial installation into existing F/P

RF24JD with RA24CA—Co-axial Vent Plate

18”

Terminal Adapter with

Flashing supplied with

590FVK2

RF24JDN/P appliance

supplied without vent plate

RA24CA (5” x 3”)

Co-axial Vent Plate

(packed separately)

Co-axial Vent Plate

Overview—with 1000K and 1000CAA Co-axial Vent Adapter

Approved 6-5/8 x 4

co-axial terminal

- sold separately. See

appliance manual for

listed terminals

18”

Terminal Adapter with

Flashing supplied with

590FVK2

Rear view

1000KN-KP appliance

supplied top co-axial

outlet

1000CAA (5” x 3”)

Co-axial Vent Adapter

(packed separately)

Co-axial Vent Adapter

Co-axial ﬂex 3 x 5 partially inserted into existing solid-

fuel burning ﬁreplace—conversion at unit

Engine

Engi

5” minimum

bending

radius

1000CAA

Co-axial Flex

Adapter

Engine

Engi

5”

minimum

bending

radius

590FVK2

co-axial 3x5

liners

Approved 6-5/8 x 4

co-axial termination

Terminal Adapter

with Flashing

supplied with

590FVK2

Co-axial ﬂex 3 x 5 fully inserted into existing solid-

fuel burning ﬁreplace—conversion at unit

1000CAA

Co-axial Flex

Adapter

28-7/16”

(722 mm)

28-7/16”

(722 mm)

590FVK2

co-axial 3x5

liners

Approved 6-5/8 x 4

co-axial termination

Terminal Adapter

with Flashing

supplied with

590FVK2

Max. 40’

(12,2 m)

Min. 10’

(3 m)

Max. 40’

(12,2 m)

Min. 10’

(3 m)

Framed

Wall

Listed clearances

to combustible

materials apply

Listed clearances

to combustible

materials apply

Installation

1. Remove 3” pipe from the 5” pipe to stretch them.

2. Carefully stretch each pipe separately to the required

length.

3. Re-insert 3” pipe into 5” pipe.

4. Trim the flashing to size if necessary. A drip edge can

be folded down.

5. Starting with 3-inch inner pipe, attach pipe assembly

to terminal adapter-flashing collars using gear

clamps and 2 sheet metal screws below clamp to

ensure pipes won’t slide off.

6. Insert pipes / adapter-flashing assembly into

chimney.

7. Secure terminal adapter-flashing to chimney.

Gear clamp

2 sheet metal screws

through collar below

clamp to prevent

sliding

3” liner 5” liner

Designed and Manufactured by / for

Miles Industries Ltd.

190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1

Tel. 604-984-3496 Fax 604-984-0246

www.valorfireplaces.com

Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication.

8. Install terminal cap to adapter-flashing and secure

with sheet metal screws.

9. Insert fireplace with co-axial vent plate or adapter

into hearth. Connect pipes to vent plate and secure

with cable clamps.

10.Add 2 sheet metal screws through vent collars above

each gear clamp to ensure it does not slip off the

collar.

11.Continue installation following instructions provided

with appliance.

Gear clamp

Gear clamp 2 sheet metal screws

through collar below

clamp to prevent sliding

3” liner 5” liner

Application

Cette trousse est conçue pour être utilisée lorsque un

des foyers indiqués ci-dessus est installé dans un foyer

et cheminée à combustibles solides existants et que la

cheminée est trop étroite pour l’installation colinéaire de

deux conduits flex de 3 pouces côte-à-côte. Le diamètre

extérieur du conduit double de la trousse 590FVK2 est

approximativement de 5-3/8 pouces.

Un raccord à buse séparée est exigé pour chacun des

foyers indiqués afin de le convertir pour les conduits

flex de 3 et 5 pouces du 590FVK2. Un adaptateur de

sortie de cheminée incorporant un solin est fourni avec

le 590FVK2 convertissant la sortie à buses de 6-5/8 x

4 pouces pour accomoder les Capuchons certifiés de

sortie coaxiale standard.

Utilisez les colliers de serrage inclus et des vis à métaux

pour bien fixer les conduits aux buses du foyer et de la

sortie. Voir les pages suivantes pour plus de détail.

NE PAS étirer trop les conduits flex—étirez-les

seulement à la longueur exigée.

NE PAS écraser, plier, déchirer ou laisseer les conduits

prendre une forme ovale.

NE PAS plier les conduits flex dans un rayon plus grand

que 5 pouces.

NE PAS raccorder deux morceaux de conduits flex.

NE PAS utiliser de conduits flex dans une construction

combustible.

Trousse d’évacuation coaxiale flex 590FVK2

INSTALLATEUR : Laissez cette notice avec

l’appareil.

CONSOMMATEUR : Conservez cette

notice pour consultation ultérieure.

GUIDE D’INSTALLATION

590FVK2

Utilisez avec les foyers Valor suivants SEULEMENT :

- 530INI/IPI Encastrable Portrait avec Raccord coaxial de foyer 530CVA2

- RF24JDN/JDP Encastrable Retrofire avec Plaque d’évent coaxial RA24CA

- 1000KN/KP H3 comme encastrable avec Raccord d’évent coaxial 1000CAA

Note

Cette trousse doit être installée ou

entretenue par un installateur qualifié,

une agence de service certifiée ou un

fournisseur de gaz. Ces instructions

doivent être utilisées conjointement

avec les instructions d’installation des

modèles de foyers Valor indiqués ici.

AVERTISSEMENT

Si les instructions fournies dans le

présent guide ne sont pas suivies

à la lettre, un feu ou une explosion

pourraient résulter et causer des

dommages matériels, des blessures

ou la mort.

AVERTISSEMENT

Cette trousse peut SEULEMENT être

installée dans un foyer et cheminée

à combustibles solides existants

fabriqués de matériaux incombustibles.

Contenu de la trousse

3” Flex pipe in

5” Flex pipe

Max. length: 40’ (12.2 m)

Gear clamps

Terminal Adapter

with Flashing

18”

5”

3”

6-5/8” x 4” collars

Buses 6-5/8” x 4”

Adaptateur de sortie

avec Solin

Conduit ﬂex de 3” dans

un conduit ﬂex de 5”

Longueur maximale :

40’ (12,2 m)

Colliers de serrage

Nettoyez le foyer et la cheminée

Procédez au ramonage de la cheminée et au nettoyage

de l’âtre du foyer incluant le bac à cendres et la trappe

à ramoner avant d’installer le foyer et les conduits

flex. Les résidus de créosote et de suie dans l’âtre de

la cheminée ou dans la trappe à ramoner peuvent

causer des odeurs désagréables ou tacher les surfaces

environnantes une fois le foyer installé. Consultez un

ramoneur pour connaître le meilleur moyen d’effectuer

le nettoyage.

Description Node pièces

Adaptateur de sortie coaxial et solin 590CVA2

Conduits ﬂex 3 x 5, incluant 2 colliers de

serrage par conduit 4006254

Concept—Encastrable Portrait 530INI/IPI avec Raccord coaxial de foyer 530CVA2

Ajoutez le 530CVA2 optionnel pour évacuation

coaxiale (conduits aux diamètre de 3” et 5”)

Vue arrière

Ajoutez le

Raccord coaxial

530CVA2

Recyclez la

plaque d’évent

fournie avec le

foyer

Sortie coaxiale

certifiée 6-5/8 x 4

- vendue

séparément. Voir

guide d’installation

du foyer pour les

sorties permises.

Rayon de

courbe

minimum

de 5”

Conduits

5 x 3”

590FVK2

Kit de conduits

5 x 3”

Raccord

coaxial

de foyer

530CVA2

Foyer

530

40’

max

8’

min

25-1/2”

[648 mm]

Adaptateur de sortie

coaxiale 5 x 3 à

[FHUWLȴ«

avec solin

Sortie coaxiale

[FHUWLȴ«H

Installation coaxiale dans un foyer existant

530INI/IPI avec Raccord coaxial 530CVA2

18”

Adaptateur de

sortie avec Solin

intégré fourni avec

le 590FVK2

Conversion à l’évent coaxial

Options d’évacuation

Indice

Lingue:

Altri manuali Valor Accessori per caminetti

Valor

Valor Horizon 615CVI Cast Surround Manuale utente

Valor

Valor LINEAR SERIES Manuale utente

Valor

Valor LT1 Series Manuale utente

Valor

Valor Horizon Matte Black Front 672MBF Manuale utente

Valor

Valor LX1 Series Manuale utente

Valor

Valor H3 Series Manuale utente

Valor

Valor Portrait Series Manuale utente

Valor

Valor 738JL Manuale utente

Valor

Valor 1725RGL-3 Manuale utente

Valor

Valor 546LFB ZC Portrait Ledgeview Front Manuale utente

Valor

Valor 1135TSBE Three Sided Trim with Edgemont... Manuale utente

Valor

Valor G4 791STB Manuale utente

Valor

Valor G3 Series Manuale utente

Valor

Valor G3.5 Series Manuale utente

Valor

Valor 752BTK Manuale utente

Valor

Valor VOGUE Series Manuale utente

Valor

Valor 546LFB Manuale utente

Valor

Valor 757 Manuale utente

Valor

Valor PORTRAIT BSK539-549-550 Manuale utente

Valor

Valor G4 790FTV Manuale utente

Valor

Valor 716EHC Manuale utente

Valor

Valor LINEAR SERIES Manuale utente

Valor

Valor Portrait 549APB Manuale utente

Valor

Valor G3.5 Series Manuale utente

Manuali Accessori per caminetti popolari di altre marche

Exodraft

Exodraft Xzense Manuale utente

Whalen

Whalen Ruso MNFP62BF23-6 Manuale utente

Lopi

Lopi Hearthview 864 Manuale utente

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuale utente

EdilKamin

EdilKamin SERBATOIO 250 Guida rapida

Bronpi

Bronpi KIT-1 Manuale utente

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuale utente

Travis Industries

Travis Industries 33 DVI Manuale utente

Superior

Superior ASD3628-TI Manuale utente

pleasant hearth

pleasant hearth OFP28WG Manuale utente

IHP

IHP Astria Series Manuale utente

Firegear

Firegear FG-H-2110SS Manuale utente

Nibe

Nibe Contura C i31 Manuale utente

kozy heat

kozy heat KZK-052 Manuale utente

SimpliFire

SimpliFire SF-WM36 Manuale utente

Bluegrass Living

Bluegrass Living BC18NR Guida rapida

pleasant hearth

pleasant hearth IRIS SCROLL Manuale utente

Cooke

Cooke Glass Wind Guard Manuale utente