Valor SFFK01 Manuale utente
Note: This kit must be installed or serviced by a quali ed installer, service agency or gas supplier.
These instructions are to be used in conjunction with the main installation instructions for the above
listed model.
WARNING: If the information in these instructions is not followed exactly, a re or explosion
may result causing property damage, personal injury or loss of life.
FOR ENGINE CONFIGURATIONS AND VENTING,
REFER TO MAIN INSTALLATION BOOKLET SUPPLIED WITH THE ENGINE.
FOR FRONT, FRET AND DOORS INSTALLATIONS,
REFER TO INSTALLATION BOOKLET SUPPLIED WITH EACH KIT.
The kit consists of a set of black sheet metal panels used to frame the 530 engine to accommodate the Front and the
Alhambra or Mesh Screen Doors. Combustible wall nish may contact the sides and top of the framing kit. The framing kit
may be installed ush or protruding from the wall nish but not recessed into the wall.
Freestyle Framing Kit components Installation diagram (See price list for choice of Fronts, Frets and Door Kits.)
Front (required,
sold separately)
Standoffs
Insulation Pad
Fret (required,
sold separately)
Doors (optional, sold separately)
Freestyle Framing Kit
(includes ZC components
shown here)
530 Engine
(required, sold
separately)
Top
Bracket
Heat
Duct
Bottom Panel
Frame
Mounting
Brackets
(4)
RH Side
Bracket
LH Side
Bracket Back Support
Bracket
SFFK01
STONEFIRE FREESTYLE FRAMING KIT
INSTALLATION INSTRUCTIONS
CSA approved for use only with
Valor Model 530 Heater
400101-04
TM
2
Note: These instructions are in addition to installation instructions supplied with Valor 530
rebox unit. Any combustible framing construction must be clear of standoffs.
A non-combustible hearth is not necessary in front of this appliance.
The 530 replace is approved to install directly on wood sub-ooring.
Any combustible framing construction must be clear of standoffs.
•
•
•
14”
26”
20”
1-1/2”
5”
6-5/8”
8-3/8”
3-5/8”
2”
Top view
Fixing
tabs to
secure
to
framing
20”
23”
26”
34-1/4”
1-1/2”
Front view
Standoff
24-1/8”
Center
of vent
Right side
3
Mantel
Depth ‘A’ 2” 4” 6” 8” 12”
Mantel
Height ‘B’ 34” 36” 38” 40” 42”
Side View
Mantel Clearance
Sidewall Clearance
CLEARANCES
Combustible
wall nish
Framing Diagram
Combustible
wall nish
Kit installed ush
with or protruding
from wall nish.
4
FRAMING KIT ASSEMBLY
Assembly Diagram
The heat duct bottom
lip ts under the edge of
the rebox top.
5
Unpack the kit and ensure you have all the components as shown on page 1.
Fix the back support bracket to the
530 engine with 2 #8 Phillips screws
supplied.
Place the bottom panel under the front
of the 530 engine. It is not necessary
to attach it to the rebox. However, if it
is desired, the panel can be xed to the
engine by drilling two holes in the panel
and xing it with 2 #10 Phillips screws
supplied.
The replace should now be leveled at
1-1/2” above the ground. If the replace
needs to be higher to accommodate oor
nish, ensure that the whole surface
underneath the replace AND the bottom
panel is raised evenly.
Fix the heat duct, the side brackets and the top bracket to the rebox with #10
Phillips screws provided. See the assembly diagram on the previous page.
Required for installation in combustible construction. Fix the standoffs to the
back of the replace with 8 #10 Phillips screws supplied.
Required for installation in combustible construction. Add the insulation pad on
top of the engine, cutting around the pipe if installing a top vent.
1.
2.
3.
4.
5.
6.
RH Side View
1-1/2”
6
On the outside of each side bracket, loosely x the frame mounting brackets—
2 per side—with the 8 #10 thread forming screws supplied.
Slide the mounting brackets at the appropriate distance from the front of the
side brackets to receive the wall nish (1/2” to 2-1/2” from the front). Tighten the
screws to x the mounting brackets.
Fix the framing kit to the studs on each side of the replace, either
for the kit to be ush with or protruding from the wall nish.
Finish the wall.
Assemble the cast front and hook it to the replace. (See instructions
provided with the cast front).
Hook the fret to the cast front. (See instructions provided with the
cast front).
If using a door kit, assemble the kit and hook the door(s) to the cast front. (See instructions provided with the
door kit.)
.
8.
9.
10.
11.
12.
13.
NOTE: When using protruding kit application with top vent, make sure
the header behind the wall nish (if used) does NOT interfere with the
vent pipe. Use the header on its narrow side to avoid interference.
Interference with
vent pipe when using
wide side of header
No interference
using the narrow
side of the
header
Designed and Manufactured for/by
MILES INDUSTRIES LTD.
190 - 2255 Dollarton Hwy., North Vancouver, BC, CANADA V7H 3B1
Tel 604-984-3496 Fax 604-984-0246
www.milesreplaces.com
© 2008, Miles Industries Ltd. All rights reserved.
1 Top Bracket 4001021AZ
2 Heat Duct 4001020AZ
3Bottom Panel 4001026AZ
4Back Support Bracket 4000825AZ
5Left Hand Side Bracket 4001014AZ
6Right Hand Side Bracket 400101AZ
Screw #10/32 x 3/8” thread form (8) 4000203
8Screw Self-Tap Pn Hd Chrome Phillips #8 x 3/8” (4) 100A5
9Frame Mounting Bracket (4) 4001022
10 LH ZC Standoff Bracket 400102
11 RH ZC Standoff Bracket 400103
12 Screw Self-Tap Pn Hd Nickel Plated Phillips #10 x 3/8” (14) 4001061
13 Insulation Pad 620B98
Hardware Kit 4001289
REPLACEMENT PARTS
1
2
3
4
5
6
8
10
11
12
13
8
12
12
12
12
12
12
9
9
9
9
8
Note: Ce kit doit être installé ou maintenu par un installateur quali é, une agence de service
certi ée ou un fournisseur de gaz. Ces instructions doivent être utilisées conjointement avec les
instructions d’installation du modèle de foyer mentionné ci-haut.
POUR LA CONFIGURATION DU FOYER ET DE L’ÉVACUATION,
RÉFÉREZ-VOUS AU MANUEL D’INSTALLATION FOURNI AVEC LE FOYER.
POUR L’INSTALLATION DE LA DEVANTURE, DE LA BASE CHANTOURNÉE ET DES PORTES,
RÉFÉREZ-VOUS AU MANUEL D’INSTALLATION FOURNI AVEC CHAQUE TROUSSE.
Pièces de l’encadrement Freestyle Schéma d’installation
(Voir la liste de prix pour votre choix de devantures, bases chantournées et portes.)
Devanture (requise,
vendue séparément)
Écarteurs
Coussin isolant
Base chantournée
(requise, vendue
séparément)
Portes (facultative, vendues séparément)
Encadrement Freestyle
(avec pièces pour
dégagement zéro)
Moteur 530
(requis, vendu
séparément)
Panneau
du haut
Canalisation
Panneau du bas
Supports
de
montage
Support du
côté droit
Support
du côté
gauche Support
arrière
MISE EN GARDE: Si les instructions fournies dans le présent manuel ne sont pas suivies à
la lettre, un feu ou une explosion pourraient résulter et causer des dommages matériels, des
blessures ou la mort.
Cette trousse contient un ensemble de pièces de métal servant à encadrer le foyer 530 et permettant l’installation d’une
devanture et de portes de style Alhambra ou à grillage. La nition du mur, même combustible, peut toucher aux côtés ou
au dessus de l’encadrement. L’encadrement peut être installé égal ou en saillie du mur de nition mais NON en retrait du
mur.
SFFK01
ENCADREMENT STONEFIRE FREESTYLE
MANUEL D’INSTALLATION
Approuvé par la CSA pour usage exclusif avec
le foyer Valor modèle 530
MC
9
Note: Ces instructions sont en plus des instructions fournies avec le foyer Valor 530. Tout
encastrement doit être construit à distance des écarteurs.
Une base de foyer non-combustible n’est pas nécessaire devant cet appareil.
Le foyer 530 est certié pour installation directement sur un sous-plancher de bois.
Tout encastrement doit être construit à distance des écarteurs.
•
•
•
36 cm
(14”)
66 cm (26”)
51 cm (20”)
4 cm (1-1/2”)
13 cm
(5”)
17 cm
(6-5/8”)
22 cm
(8-3/8”)
9 cm
(3-5/8”)
5 cm
(2”)
Fixing
tabs to
secure
to
framing
20”
23”
26”
34-1/4”
1-1/2”
24-1/8”
Center
of vent
Devant
Supports de
montage pour
xation à
l’encastrement
51 cm (20”)
58 cm (23”)
66 cm (26”)
8 cm (34-1/4”)
4 cm (1-1/2”)
Centre
de l’évent
61 cm (24-1/8”)
Côté droit
Dessus
Écarteur
10
Profondeur de
manteau ‘A’
5 cm
(2”)
10 cm
(4”)
15 cm
(6”)
20 cm
(8”)
30 cm
(12”)
Hauteur du
manteau ‘B’
86 cm
(34”)
91 cm
(36”)
9 cm
(38”)
102 cm
(40”)
10 cm
(42”)
Côté droit
Dégagement pour tablette
ou manteau de cheminée
Dégagement d’un
mur de côté
DÉGAGEMENTS
Finition
combustible
Schéma d’encastrement
Finition
combustible
Encadrement
égal ou en saillie
de la nition
Dégagement min. de 5
cm (2”) d’un mur de côté
(permettre plus d’espace pour les coudes dans les évacuations arrières)
88 cm
(34-1/2”)
du sol à la
poutre du
dessus et
nition du
mur
Manteau ou
tablette
combustible
6 cm (26-1/2”)
36 cm (14”)
1 cm
(1/2”)
6 cm
(2-1/2”)
Altri manuali per SFFK01
1
Indice
Lingue:
Altri manuali Valor Camino da interno
Valor
Valor Legend G3 738 NGK Manuale utente
Valor
Valor Ultimate 717 Manuale utente
Valor
Valor 719 Istruzioni per il montaggio
Valor
Valor 1200EAN (NG) Istruzioni per l'installazione
Valor
Valor 1500IN Istruzioni operative
Valor
Valor 639 Istruzioni per il montaggio
Valor
Valor tuscany 637 Manuale utente
Valor
Valor HORIZON 534XAN Manuale
Valor
Valor 1500IN Istruzioni operative
Valor
Valor Dream 2 Istruzioni per il montaggio
Valor
Valor 517 Manuale utente
Valor
Valor LX1 Series Manuale utente
Valor
Valor 785ILN Manuale utente
Valor
Valor 5402 HOMESTYLE Manuale utente
Valor
Valor PORTRAIT 536CXBI Manuale utente
Valor
Valor AutoFire G3.5 Manuale utente
Valor
Valor Homeflame Dream Manuale di istruzioni
Valor
Valor H6 Series Istruzioni per l'installazione
Valor
Valor PORTRAIT 539 Istruzioni per l'installazione
Valor
Valor LT1 2500KN Manuale utente
