Vantron TMC Series Manuale utente

Vantron | Embedded in your success, Embedded in your better life

World-leading provider of embedded/IoT products and solutions

TMC series | Quick Installation Guide www.vantrontech.com

Vantron TMC Series Desktop/Wall-mountable

Touchscreen Monitors

Quick Installation Guide

Version: 1.2

General Safety Instructions

For your safety and prevention of damage to the Product, please read and observe carefully the following safety instructions prior to installation and operation. Keep this guide well

for future reference.

°Do not disassemble or otherwise modify the Product. Such action may cause heat generation, ignition, electronic shock, or other damages including human injury, and may void

your warranty.

°Keep away from heat source, such as heater, heat dissipater, or engine casing.

°Do not insert foreign materials into the openings of the Product as it may cause the Product to malfunction or burn out.

°Use only the adapter and power cord that are approved for use with this Product. Otherwise, it may cause fire or explosion.

°Be sure that nothing rests on the power cable and that the cable is located at a place without risk of trips.

°Cut off the power before inspection of the Product to avoid human injury or product damage.

°It is recommended to avoid leaving static images on the screen for extended periods of time, as this may lead to temporary image retention or "burn-in". For best practices, you

are advised to use screen savers or power-saving settings while not operating the device for an extended period.

ESD Precautions

While setting up an electronic system or handling electronic components, certain precautions and proper handling procedures should be followed to prevent ESD-induced failures.

Careless handling of ESDS components can degrade their reliability and life expectancy.

Electrostatic discharge (ESD) events can harm electronic components inside the Product. Under certain conditions, ESD may build up on your body or an object, such as a peripheral,

and then discharge into another object, such as the Product. To prevent ESD damage, you should discharge static electricity from your body before you interact with any of the

Product’s internal electronic components.

You can protect against ESD and discharge static electricity from your body by touching a metal grounded before you interact with anything electronic component on the Product.

When connecting a peripheral to the Product, you should always ground both yourself and the peripheral before connecting it to the Product. In addition, as you open the Product for

maintenance, periodically touch a metal-grounded object to remove any static charge your body may have accumulated.

Disclaimer

While all information contained herein has been carefully checked to assure its accuracy in technical details and typography, Vantron does not assume any responsibility resulting

from any error or features of this manual, nor from improper uses of this manual or the software.

It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the

Product may be changed without notice.

Please refer to the user manual of this series for more information on safety cautions and regulatory compliance statements.

Vantron Technology, Inc.

Address: 48434 Milmont Drive, Fremont, CA 94538

Tel: (650) 422-3128

Email: [email protected]

Vantron | Embedded in your success, Embedded in your better life

World-leading provider of embedded/IoT products and solutions

TMC series | Quick Installation Guide www.vantrontech.com

1. COMPONENT CHECKLIST

Check if all components are available:

•Touchscreen monitor

•Power adapter & power cable

•Touch USB cable

•HDMI cable & VGA cable

•DP cable (Optional, applicable only to TMC215 and TMC270)

Note: Actual accessories might vary slightly from the list above as the customer

order might differ from the standard configuration options.

2. INSTALLATION OF THE TOUCHSCREEN MONITOR

Vantron TMC series desktop/wall-mountable touchscreen monitors are

designed to be mounted onto a variety of stands, arms, walls or medical charts

with VESA patterns (75mm x 75mm and 100mm x 100mm) on the back.

Drawing for illustration only. The VESA pattern on TMC156 is 75mm x 75mm.

Screw specifications:

•M4 screws

•Thread depth: 8mm

3. WIRING

1. Connect the video input interface of the touchscreen monitor and the video

source with an HDMI/VGA/DP cable;

Note: The DP port is exclusive for TMC215 & TMC270. The display cable

shall vary with the display interface, and adapter connectors are

sometimes needed.

2. Connect the USB port of the touchscreen monitor and the PC/master device

(e.g., Vantron IBOX3588) with the touch USB cable to enable the touch control;

3. Plug in the audio cable, if needed;

Note: The audio interface is implemented as per the requirement of the

customer.

4. Connect a 12V DC power supply to the power jack of the device, and the

LED indicator will turn solid red and enter the sleep mode;

5. Wait about 2-3 seconds and the LED indicator will turn solid green if the

PC/master device connected to functions properly;

6. Use the OSD control buttons at the bottom of the monitor to power off

the device or change the display settings.

4. LED INDICATOR AND OSD CONTROL

The relationship between the power indicator and the touchscreen monitor

status is as follows:

Indicator status Touchscreen monitor status

OFF

Solid red SLEEP

Solid green

WORKING

OSD control buttons function as follows:

Key OSD panel not displayed OSD panel displayed

Menu OSD menu Enter the submenu of a selected

parameter

Up OSD Contrast submenu

(Increase brightness)

Increase value of selected parameter/

Move to next menu upwardly

Down OSD Brightness submenu

(Decrease brightness)

Decrease value of selected parameter/

Move to next menu downwardly

Back NA Return to previous OSD menu

5. TROUBLESHOOTING

Please refer to the following solutions/suggestions in case you encounter a

trouble during use of the touchscreen monitor.

If the problem is not covered here or the problem persists after

troubleshooting, please contact your sales representative.

1. The touch screen does NOT respond when the device is powered on.

-Check if the DC power adapter is properly connected and functions well.

2. The screen is dim.

-Use the OSD control buttons to adjust the brightness or contrast of the

display.

3. The touchscreen monitor does NOT wake up automatically and the power

indicator is red.

-Tap the screen and wait for the monitor to respond. If it fails, press the

power button, or re-connect the power supply, and wait a few seconds till

the indicator turns green.

4. The image is NOT properly displayed.

-Adjust the resolution/timing mode of the PC/master device to be within

the allowable ranges specified for the touchscreen monitor. Or, adjust the

display parameters manually with the OSD control buttons.

VGA

HDMI

Altri manuali per TMC Series

Altri manuali Vantron Schermo tattile

Vantron

Vantron TMO Series Manuale utente

Manuali Schermo tattile popolari di altre marche

Elecro Engineering

Elecro Engineering Poolsmart Plus Istruzioni per l'installazione

Johnson Controls

Johnson Controls IQ4 HUB Manuale utente

Elo TouchSystems

Elo TouchSystems ET2270L Manuale utente

Elo TouchSystems

Elo TouchSystems ET1002L Manuale utente

Elo TouchSystems

Elo TouchSystems 3201L Manuale utente

Duratec

Duratec S15 Manuale utente

Crestron

Crestron TPMC-3SM Manuale utente

Racelogic

Racelogic MFD Touch Manuale utente

J2 580 Guida utente

HAI

HAI OmniTouch 10p Manuale utente

panel

panel PC PSR108-FM Series Manuale utente

Tipro

Tipro FREE+ Manuale utente

Systemline

Systemline Commander Manuale utente

Interactive Technologies

Interactive Technologies Insite Manuale utente

GVision

GVision Legacy Manuale utente

BeiJer

BeiJer T21C-C24 Manuale utente

Advantech

Advantech ITM-5117 Series Manuale utente

Edge

Edge CS Manuale utente