Vaporesso Target 80 Manuale utente
User Manual
Thank you for choosing Vaporesso product. Please read this instruction carefully before use to ensure a perfect
experience. If there is any additional requirement about this product, please consult the local agent or contact us
through our website: www.vaporesso.com
Drip Tip
Power Button
0.96" TFT Screen
“+” Button
Mode/ Confirm Button
“-” Button
Type-C USB Port
PCTG Tube
Top Cap
Air-inlet Port
EXPLODED VIEW
SPECIFICATIONS
Dimensions: 130.9 x 38.3 x 30.8mm
POD Capacity: 5ml/2ml(TPD)
Coils & Suggested Waage:
GTX 0.2ΩMESH Coil (45-60W)
GTX 0.3ΩMESH Coil (32-45W)
Baery Capacity: 3000mAh
Output Power: 5-80W
Charging Current: DC 5V/2A,Type-C
Baery Display: 0.96’’ TFT Screen
PACKING LIST
1 x TARGET 80 MOD
1 x GTX PODTANK 26 (5ml/2ml TPD)
1 x GTX 0.2Ω MESH Coil (In-BOX)
1 x GTX 0.3Ω MESH Coil (In-BOX)
1 x Type-C Cable
1 x User Manual
1 x Warranty Card
FIGURES
Figure 1: Replace the coil
Figure 2: Fill e-liquid
OPEN CLOSE
1
English
ENGLISH
USE INSTRUCTIONS
1. Install the Tank
Install the tank to the battery by screwing the 510 thread. Make sure they are firmly connected.
2. Replace the Coil
- Place the drip tip of the pod face down, and pull out the used coil;
- Install a new coil to the pod;
- Press the coil to align the coil base with the pod.
* Refer to the figure 1.
3. Fill E-liquid
- Unscrew the top cap from the pod;
- Fill e-liquid through the filling slot;
- Screw the top cap to reinstall it back into place as shown;
- Please wait 5 minutes for the e-liquid to soak into the coil completely.
* Refer to the figure 2.
4. Adjust the Airflow
Please rotate the pod to match the air-inlet port to adjust the airflow volume.
5. Power On/Off the Device
Power on/off: press the power button 5 times in 2s.
6. Power Adjustment
TARGET 80 Kit is using the powerful GTX coil platform, and the suggested power need to be noticed
before start vaping.
GTX MESH Coils GTX 0.2Ω MESH GTX 0.3Ω MESH
Suggested Power 45-60W 32-45W
7. Start Vaping
Press the power button to enjoy extraordinary vaping experience.
2English
8. Charge the Baery
After connecting the Type-C cable to the battery, the battery indicator and remaining charging time will be showed on
the screen.
9.Lock or unlock the device
Press the fire button 3 times, then the +, - and mode buttons will be locked. In the same way, the buttons will be
unlocked and the screen will be unlocked.
10. Choose a Mode
1. Long press the mode button for main mode selection (Pulse Mode/F(t) Mode/VWN Mode).
2. Press the mode button 3 times continuously for secondary menu setting.
*F(t): F(t) MODE (DEFAULT)
F(t) MODE is by adjusting temperature,
heating speed and time, F(t) mode releases
the flavors of e-liquid adequately, delivering
the perfect balanced tasting experience
consistently from the first puff throughout.
*DIY: DIY MODE
You can choose traditional VW (H, N, S), VV,
BP (Bypass) modes in this section.
*PUL: PULSE MODE (DEFAULT)
PULSE MODE: It’s a mode to improve
vaping experience through constant voltage
output, delivering optimal flavor production,
throat hit, nicotine satisfaction, and perfect
temperature cloud continuously.
*SET: SYSTEM SET
System setting includes DEFAULT, SMART VW,
PUFF, and VERSION options.
SMART VW: when this function is turned
on and a POD is installed, the system will
recommend the best power.
3
English
1. Short circuit protection & Low resistance protection:
When the load resistance is less than 0.1±0.01Ω, press power button could trigger the short circuit protection or Low
resistance protection, the device will close the output, at the same time OLED display will show “SHORT ATOMIZER”.
2. No load protection:
When no load resistance is detected, press power button could trigger the no load protection, the device will close the
output, at the same time OLED display will show “CHECK ATOMIZER”.
3. High resistance protection:
When the load resistance is greater than 5±0.5Ω, press power button could trigger the high resistance protection, the
device will close the output, at the same time OLED display will show “ CHECK ATOMIZER ”.
4. Low voltage protection:
When the voltage of the battery cell is lower than 3.3±0.1V, press power button could trigger the low voltage protection,
the device will close the output, at the same time OLED display will show “LOW BATTERY”.
5. PCBA(Printed Circuit Board Assembly):
When the temperature of the PCBA(Printed Circuit Board Assembly) temperature sensor is higher than 70+5℃/-10℃,
press power button could trigger the PCBA (Printed Circuit Board Assembly) over heat protection, the device will close
the output, at the same time OLED display will show “OVER HEAT”.
6. Over discharge protection:
During the process of smoking, when the battery cell voltage is lower than 2.9±0.1 V, the device will close the
output automatically.
7. Over charge protection:
During charging, when the battery cell voltage is greater than 4.1±0.1V, OLED display will show “100%”. At the end of
charging, battery cell voltage will not exceed 4.2±0.03V.
8. Auto-shut off protection:
When POWER button is held for 10±1 seconds, the device will close the output, at the same time OLED display will
show “OVER TIME”.
9. Baery cell anti-reverse connection protection:
The inversion of battery cell will not damage the battery.
PROTECTIONS
4English
1. Please turn off the device when it is not in use.
2. Do not leave the charging device unattended.
3. Do not drop, throw or abuse your device, which may cause damage.
4. Please use a standard USB output charger with proper charging current and voltage range.
5. Keep away from the water or any flammable gas, liquid .
6. Do not expose the device to direct sunlight, dust, moisture or mechanical shock.
7. Do not expose the device to extreme temperature. (Recommended temperature range: -10~60℃/14~140℉while
using and -10~45℃/14~113℉while storing).
8. EEE Recycling: the product should not be treated as household waste, instead, it should be handed over to the
applicable collection point for the recycling of electrical and electronic equipment.
9. Battery Recycling: the product battery should not be treated as household waste, instead, it should be handed over
to the applicable used battery collection point for recycling.
10. Only have your device repaired by Vaporesso. Do not attempt to repair it by yourself as damage or personal injury
may occur.
WARNINGS
This refillable electronic cigaree is intended for use with compatible e-liquid, which may contain nicotine. Nicotine is
an addictive substance and it is not suitable or recommended to use in following cases:
1. This device is not suitable for:
- Persons under the legal smoking age.
- Persons experiencing heart disease, stomach or duodenal ulcers, liver or kidney problems, long-term throat disease
or difficult breathing due to bronchitis, emphysema or asthma.
- Persons with an overactive thyroid gland or experiencing phaeochromocytoma (a tumour of the adrenal gland that
can affect blood pressure).
- Persons taking certain medications like Theophylline, Ropinirole or Clozapine and etc..
CAUTIONS
5
English
2. This device is not recommended for:
- Non-smokers
- Pregnant or breastfeeding women
3. You may experience the following results if you use nicotine containing e-liquid with this product. If it happens,
please consult a healthcare professional and show them this leaflet if possible:
- Feeling faint - Nausea - Dizziness - Headache - Coughing - Irritation of the mouth or throat
- Stomach discomfort - Hiccups - Nasal congestion - Vomition
- Chest palpitations/pain or an irregular heart rate
This device should not be used by persons under the legal smoking age.
1Français
FRANÇAIS
CONSIGNES D’UTILISATION
1. Installation du réservoir
Installez le réservoir sur la batterie en les vissant ensemble grâce au filetage 510. Vérifiez qu’ils sont fermement
connectés.
2. Remplacement de la résistance
- Tournez l’embout de remplissage du POD vers le bas, et tirez sur la résistance coil usée pour la retirer ;
- Installez une nouvelle coil sur le POD ;
- Appuyez sur la coil pour aligner sa base sur le pod.
* Voyez la figure 1.
3. Recharge de l’e-liquide
- Dévissez le bouchon du haut du POD en suivant le sens de la flèche ;
- Versez l’e-liquide dans le trou de remplissage ;
- Vissez le bouchon du haut pour le remettre en place comme illustré ;
- Veuillez patienter 5 minutes, le temps que l’E.-liquide imbibe complètement la résistance.
* Voyez la figure 2.
4. Réglage du débit d’air
Veuillez faire tourner le POD pour aligner le port d’entrée d’air sur la batterie et ajuster le débit d’air.
5. Mise en marche/arrêt de l’appareil
- Marche/Arrêt : appuyez sur le bouton d'alimentation à 5 reprises en 2 secondes.
6. Réglage de la puissance
Le kit TARGET 80 utilise la plateforme GTX puissante, et il est donc nécessaire de vérifier la puissance
avant de commencer à vapoter.
7. Commencer à vapoter
Appuyez sur le bouton d’alimentation pour vivre une expérience de vapotage extraordinaire.
Résistances GTX MESH GTX 0,2Ω MESH GTX 0,3Ω MESH
Puissance suggérée 45-60 W 32-45 W
Altri manuali per Target 80
1
Indice
Lingue:
Altri manuali Vaporesso Vaporizzatore
Vaporesso
Vaporesso GEN FIT 40 Manuale utente
Vaporesso
Vaporesso VECO SOLO Kit Manuale utente
Vaporesso
Vaporesso GEN NANO Manuale utente
Vaporesso
Vaporesso BARR Manuale utente
Vaporesso
Vaporesso TARGET PM80 Manuale utente
Vaporesso
Vaporesso LUXE PM40 Manuale utente
Vaporesso
Vaporesso XTRA Manuale utente
Vaporesso
Vaporesso XROS 3 NANO Manuale utente
Vaporesso
Vaporesso GTX GO 80 Manuale utente
Vaporesso
Vaporesso Switcher Manuale utente
Vaporesso
Vaporesso PodStick Manuale utente
Vaporesso
Vaporesso VECO DEVIL Manuale utente
Vaporesso
Vaporesso ARMOUR MAX Manuale utente
Vaporesso
Vaporesso SWAG PX80 Manuale utente
Vaporesso
Vaporesso XIRON Manuale utente
Vaporesso
Vaporesso VECO SOLO PLUS Manuale utente
Vaporesso
Vaporesso XROS MINI Manuale utente
Vaporesso
Vaporesso Target MINI II Kit Manuale utente
Vaporesso
Vaporesso VECO ONE Manuale utente
Vaporesso
Vaporesso Drizzle Tank Manuale utente
