Vaporfi VOLT 2 Manuale utente
QUICK START GUIDE
ENGLISH
WHAT’S INCLUDED
» [ 1 ] 4 ML Tank
» [ 1 ] SSOCC 0.5ohm Nichrome Atomizer
(Pre-Installed)
» [ 1 ] OCC 1.5ohm Atomizer
» [ 1 ] SSOCC Ni200 0.15 ohm Atomizer
» [6] O-Rings
» [ 1 ] Quick Start Guide
PRIMING & FILLING YOUR VOLT 2 TANK
1. Turn your tank upside down and unscrew atomizer base
from the tank.
2. Drop 3 drops of e-liquid into the exposed cotton holes
ensuring to wet each exposed cotton hole.
3. Screw the atomizer base back into the tank ensuring that
the atomizer base is snug but not too tight.
4. Unscrew the top fill cap by gripping the drip tip base
counter clockwise.
5. Use the top fill ports to fill your e-liquid to no more than
3/4 of the tank capacity.
CHANGING YOUR VOLT 2 ATOMIZER
Atomizers will endure anywhere between 7 – 14 days
depending on use and must be replaced when it has burned
out or no longer produces the proper volume of vapor.
1. Ensure that your tank is completely empty of e-liquid.
2. Remove the atomizer base from the tank and set the top
6. Once your e-liquid is filled, screw the top cap back
onto the tank and let your e-liquid soak the atomizer for 5
minutes.
7. Once Your liquid has properly saturated your atomizer,
you are ready to vape.
section of the tank aside.
3. Unscrew the atomizer using a counter clockwise motion
and discard the used atomizer.
4. Take a fresh atomizer and screw it into the tank base in
a clockwise motion. Ensure that your atomizer fits snuggly
without over tightening.
5. Follow the aforementioned steps to prime and fill your
tank then enjoy your favorite E-Liquid.
USING THE VOLT SERIES RBA IN YOUR VOLT 2 TANK
1. Follow the aforementioned steps to remove your atomizer.
NOTE: DO NOT REBUILD THIS DECK IF YOU ARE NOT AN
EXPERIENCED USER. REBUILDING AN RBA REQUIRES
KNOWLEDGE OF OHMS LAW AND A GREATER LEVEL OF
PATIENCE THEN A PRE-BUILT ATOMIZER.
BUILDING YOUR RBA DECK
2. Prime your RBA by dropping liquid onto the exposed
cotton while ensuring that you also drop generous amounts
of e-liquid onto the exposed coil as well.
3. Follow the previously mentioned steps to priming and
filling your tank and enjoy your favorite e-liquid.
1. To Rebuild your RBA, unscrew the top cap and side screw
to reveal the buildable deck.
2. Once this rebuildable deck is exposed, unscrew your used
replacement wire and discard it.
3. Take the replacement Volt Series RBA Replacement Wire
and mount into the screw holes and tighten the screws. (Be
sure to tighten the screws as much as possible in order to
ensure the best possible contact.)
4. Feed cotton into the center wrap of the wire and pull the
cotton through. Once the cotton is fed through the wire
hole, cut the cotton ensuring that it sits snuggly into the
deck.
NOTE: To ensure the most effective cotton feed, twist your
cotton between your finger tips and make a small point with
the leg of your cotton. When the cotton is able to enter the
wire, twist from both sides and feed it gently into the wire
opening. After the cotton has been guided through the wire
opening, cut both sides to fit into the RBA head.
5. Screw side screw back onto the RBA and screw the top
cap back onto RBA.
AIRFLOW CONTROL RING
To Adjust your airflow, twist the bottom airflow ring to your
TROUBLE SHOOTING YOUR VOLT 2 TANK
FLOODING:
If your tank begins to spit back, gurgle or produce less
preference. Cutting a 1/4 of the airflow is recommended for
users looking to achieve a restricted direct to lung draw.
To achieve a mouth to lung draw when using the 1.5 ohm
OCC coil, Close the airflow to 50%. It is not recommend to
completely close off the airflow as this will cause flooding
and spit back.
Indice
Altri manuali Vaporfi Vaporizzatore
Vaporfi
Vaporfi V-GRIP Manuale utente
Vaporfi
Vaporfi V-GRIP 220 Manuale utente
Vaporfi
Vaporfi PRO II Manuale utente
Vaporfi
Vaporfi VEX 75 TC Manuale utente
Vaporfi
Vaporfi Rebel Manuale utente
Vaporfi
Vaporfi VOX 60 TC Manuale utente
Vaporfi
Vaporfi VAIO 75 TC Manuale utente
Vaporfi
Vaporfi ATOM Istruzioni operative e di manutenzione
Vaporfi
Vaporfi VAIO 75 TC Manuale utente
Vaporfi
Vaporfi AIR 2 Manuale utente
