VCL Orbiter Gold Microspheres Manuale utente
Video Controls Limited
Document Number - MNGLXXXX0901UK
OrbiterGold/OrbiterLite
Microspheres
with user selectable Coax and Twisted Pair Telemetry modes
Owners Operation & Installation Guide
Owners Operation & Installation Guide Orbiter Gold / Lite
© Video Controls Limited 2001 MNGLXXXX0901UK Page i
Table of
Contents
Safety Instructions, Maintenance & Fault
Finder iii
1 Installing the Orbiter Gold / Lite 1
1.0 Installing the Orbiter Gold / Lite 1
2.0 Sample Configurations and Notes for
RS485 Twisted Pair Installations 10
2 Setting up the Orbiter Gold / Lite 13
1.0 Wiring Details 13
2.0 Settings on the Orbiter Gold / Lite Top
Board (VC472) 16
3.0 Address Settings 17
4.0 Coax Telemetry 18
5.0 Alarm Settings 18
6.0 LED on the Orbiter Gold / Lite Bottom
Board (VC472) 20
7.0 Alarm / Relay Connections 21
3 Technical Specification 23
4 Equipment Returns Procedure 31
1.0 For Repair 31
2.0 For Credit 32
Orbiter Gold / Lite Owners Operation & Installation Guide
Page ii © Video Controls Limited 2001 MNGLXXXX0901UK
Table of
Contents
Owners Operation & Installation Guide Orbiter Gold / Lite
© Video Controls Limited 2001 MNGLXXXX0901UK Page iii
Safety
Notes
Safety Instructions, Maintenance & Fault Finder
WARNING! Read these notes before attempting to
operate the Orbiter Gold / Lite
WARNING! Do not use the camera continuously for a
period of over twenty-four hours with the auto-focus on.
Doing so may damage the lens.
Refer all servicing to qualified personnel.
These products are for internal use only.
These products contain static electricity sensitive devices. Please take
appropriate precautions when handling.
Handle the Orbiter Gold / Lite with care, as improper handling may
cause irreparable damage to the precision or sensitive parts within this
unit.
Never point the camera directly towards a bright light source (for
example sunlight), or expose the camera to intensive light situations as
this may damage the camera pick-up device.
This information andour technicaladvice - whether verbal, in writing,
or by way of trials - is given in good faith but without warranty and
this also applies where proprietary rights of third parties are involved.
Our advice does not release you from your obligation to check its va-
lidity and to test our products suitability for the intended purpose(s)
and use(s). The application, use and installation of our products either
in isolation or in conjunction with other products used, provided and/
or installed by you on the basis of our technical advice are beyond our
control and therefore remain entirely your own responsibility. VCL
products are sold in accordance with our General Conditions of Sale
and Delivery.
ALL DESIGNS AND SPECIFICATIONS ARE SUBJECT TO
CHANGE WITHOUT NOTICE
© VCL 2001 Maintenance
Cleaning the Acrylic
VCL Recommend that the Acrylic on this product is cleaned regularly.
For cleaning, VCL suggests that the acrylic is cleaned using a
propriety foam cleaner or methalyted spirits and a soft cloth.
Orbiter Gold / Lite Owners Operation & Installation Guide
Page iv © Video Controls Limited 2001 MNGLXXXX0901UK
Safety
Notes
Fault Finder
Owners Operation & Installation Guide Orbiter Gold / Lite
© Video Controls Limited 2001 MNGLXXXX0901UK Page 1
Chapter 1
Installation
Installing the Orbiter Gold / Lite
Note: When handling the Orbiter Gold / Lite DO NOT
touch the acrylic, or any sensitive or precision parts,
as this will cause damage to the unit.
1.0 Installing the Orbiter Gold / Lite
1.1 Ceiling and Wall Mounted Models
Figure i, below, details the ceiling and wall mount
brackets, including dimensions.
Figure i Mounting Brackets for Orbiter Gold / Lite
54mm 80mm
80mm
82mm 100mm SQ
42mm
12mm WIDE
SLOT FOR
CABLES
ON R30
M5 OR No10 FIXINGS
WALL / CEILING MOUNT
VC5S-80 88mm POLE
VC5S-300 300mm POLE
VC5S-600 600mm POLE
VC5S-900 900mm POLE
M8 FIXINGS –
VC5S-1200 1200mm POLE
VC5S-1800 1800mm POLE
VC5S-3000 3000mm POLE
WALL MOUNT BRACKET
VC5S-WB CEILING MOUNT BRACKETS
161mm
142mm
Orbiter Gold / Lite Owners Operation & Installation Guide
Page 2 © Video Controls Limited 2001 MNGLXXXX0901UK
Chapter 1
Installation
Step Instruction
1 Attach the bracket (wall or ceiling type) using fixings
whichareappropriateforthe surface and able tosupport
the weight of the Orbiter Gold / Lite (1.1 kg) as shown
in Figure ii.
Figure ii Fitting the Orbiter Gold / Lite into the bracket
Step Instruction
2 Align the lug on the Orbiter Gold / Lite with the slot on
the bracket. Carefully push the Orbiter Gold / Lite into
the bracket and twist clockwise. Allow to drop into the
retainer. See Figure iii.
Figure iii Fitting the Orbiter Gold / Lite into the bracket
PUSH UP POLE –
ALIGN LUG TO SLOT
PUSH UP TWIST
Owners Operation & Installation Guide Orbiter Gold / Lite
© Video Controls Limited 2001 MNGLXXXX0901UK Page 3
Chapter 1
Installation
Step Instruction
3 Fit the M3 CSK safety locking screw into the bracket to
lock the Orbiter Gold / Lite in place. This is
ESSENTIAL for the safe operation of the Orbiter Gold
/ Lite. (The hole for the screw is on the opposite side of
the pole to the slot.)
4 Attach the cable cover. This is supplied as two halves
which snap together over the neck of the Orbiter Gold /
Lite as shown in Figure iv, below.
Figure iv Fitting the Cable Covers
&DEOH &RYHU
KDYOHV VQDS WRJHWKHU
Orbiter Gold / Lite Owners Operation & Installation Guide
Page 4 © Video Controls Limited 2001 MNGLXXXX0901UK
Chapter 1
Installation
1.2 False Ceiling Model
Note: The Orbiter Gold / Lite is designed to be mounted in
aflatceilinginstallation.MountingtheOrbiterGold
/ Lite in an angled ceiling installationwill affect the
units centre of gravity and, consequently,
programmed tours will be affected.
Note: The false ceiling kit requires a clear area of 270mm
diameter for installation. See Figure v for details.
Figure v Dimensions Required for False Ceiling Kit
Step Instruction
1 Ensurethatthefalseceilingisabletosupporttheweight
of the false ceiling kit. (1.25 kg)
2 Using the retaining ring as a template, cut a 160mm
diameter hole in the ceiling using an appropriate tool.
3 Drill three 6mm holes on the 186mm PCD to accept the
mounting studs.
50mm (2”) LANYARD
RETAINING
DISC
270mm (10.7”)
148mm (5.9”)
145mm (5.8”)
75mm (3”)
Questo manuale è adatto per i seguenti modelli
1
Indice
