Vectrix VX-2 Manuale utente
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
www.vectrix.com
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
CONTENTS
SECTION A: Tools
1 Tools Needed
2 VX-2 Major Components Identification
SECTION B: Mechanical Parts
1 Front Fairing
2 Front Console Cover/Wind Deflector
3 Speedometer Cover
4 Front Vertical Panel Cover-Lower
5 Front Vertical Panel Cover-Upper
6 Center Step-Through Cover
7 Front Fender
8 Seat
9 Under Board/Belly Pan
10 Foot Rest
11 Crossover/Tail Light Assembly
12 Rear Side Body Panels/Side Emblem
13 Rear Fender-Top
14 Side Cover/Swing Arm Cover
15 Front Wheel
16 Front Brake Master Cylinder/Line/Caliper
17 Rear Brake Master Cylinder/Line/Caliper
18 Rear Shock
19 Rear Swing Arm/Motor Assembly
20 Handlebar
SECTION C: Electrical Parts
1 Speedometer
2 Throttle
3 Brake Switch
4 Handlebar-Left Switch Assembly
5 Handlebar-Right Switch Assembly
6 Ignition Switch
7 Horn
8 Position Light/Headlamp Assembly
9 Front Turn Indicator Assembly
10 Side Stand Switch
11 Rear Tail Light Assembly
12 License Plate Light Assembly
13 Rear Turn Indicator Light Assembly
14 Motor Controller
15 Motor
16 Battery
17 Battery Charger
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
SECTION D: Adjustments
1 Front Headlamp/Position Light Adjustment
SECTION E: Troubleshooting
1 Indication on Speedometer Display & Controller LED
2 Malfunctions
3 Check of Charger Function
SECTION F: Technical Information
1 Cable Assembly-Front Brake/Turn Indicators + BOM
2 Cable Assembly-Front Headlamp/Horn + BOM
3 Cable Assembly-Rear Brake/Indicators/Tail Light/Battery/Side Stand + BOM
4 Torque List for Bolts/Nuts
SECTION G: Unpacking/Prep
1 Unpacking Instructions
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
SECTION A-1: TOOLS NEEDED
For repairing and testing of the VX-2 scooter the following tools are needed:
Tools:
Description
Specification
Open wrench
5.5mm
Open wrench/Turned Full-
contact (#S02445)
8mm
Open wrench
10mm
Open wrench
12mm
Open wrench
13mm
Open wrench
14mm
Open wrench
16mm
Open wrench
17mm
Open wrench
18mm
Open wrench
19mm
Open wrench
32mm
Open wrench
45mm
Special tool/Motor Nut
(contact service@vectrix.com)
42mm spanner
socket with
22mm relief slot
Torque wrench
0-20Nm
Torque wrench
10-100Nm
Spanner socket
12mm
Spanner socket
13mm
Spanner socket
14mm
Spanner socket
17mm
Allen key
2.5mm
Allen key
4mm
Allen key
5mm
Allen key
6mm
Phillips screwdriver
#1
Phillips screwdriver
#2
Phillips screwdriver
#3
Screwdriver, flat
4.5mm
Screwdriver, flat
9mm
Security TORX Screwdriver
TX10
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
SECTION A-2: VX-2 MAJOR COMPONENTS IDENTIFICATION
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
SECTION B
The following SECTION B instructions are for the VX-2 MECHANICAL
disassembly/assembly. Unless otherwise noted in each procedure, assemble all parts
in the reverse order in which they were taken apart. If you have any questions
regarding VX-2 Mechanical disassembly/assembly procedures, please contact
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
SECTION B-1: FRONT FAIRING
To protect the front fender, put plastic wrap or other soft
material onto the fender
Unscrew the 6 Phillips screws 1 to 6 in order as seen in
the picture with a Phillips screwdriver PH2
Remark:
While loosening screws 7 and 8 hold the front fairing
otherwise it drops down and could break!
Remark:
While loosening screws 7 and 8 hold the front fairing
otherwise it drops down and could break!
To unplug the headlight assembly, hold the front fairing
and loosen all the connectors of the headlight
To reassemble after unplugging the headlight assembly,
please be sure the clamp nuts are in the correct position
Remark: For assembling the Front Fairing, please make sure the attachment points are in the right
position and no edge is protruding. Insert the screws slightly and if all screws and the
fairing are in the correct positions, then tighten them fully.
See also the last picture in the next Section for the correct position of the clamp screw.
1
4
5
8
7
6
3
2
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
SECTION B-2: FRONT CONSOLE COVER/WIND DEFLECTOR
Locate four Phillips screws underneath the Front Console
Cover/Wind Deflector and remove
Slide in a flat screwdriver into the position as seen on the
picture. Hold the front console cover by hand. Carefully
turn the screwdriver counter-clockwise [ccw] (left side) and
clockwise [cw] (right side) until the front cover snaps out.
From the rear of the assembly, unscrew the four Phillips
screws (left and right position) with a Phillips screwdriver
PH2
Remark: For assembling the Front Console Cover/Wind Deflector, please make sure the
attachment points are in the correct position and no edge is protruding. Insert the screws
slightly and if all screws and the cover are in the correct positions, then tighten them fully.
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
SECTION B-3: SPEEDOMETER COVER
Preparations:
Disassemble Front Console Cover/Wind Deflector see Section B-2
Unplug the connector from the base of the Speedometer
Unscrew the left and right Phillips PH2 screws
Remove the Speedometer and Cover
https://www.motorcycle-manual.com/
VECTRIX VX-2 SERVICE MANUAL
Version 1.0/July 2011
VECTRIX, LLC
SECTION B-4: FRONT VERTICAL PANEL COVER-LOWER
Unscrew the four PH2 Phillips screws (Top + Bottom and
Left + Right position)
Slide a Phillips screwdriver into the hole and carefully pull
back the cover slowly to the left. Use your fingers to hold
the cover and pull backward
Slowly pull back the cover and remove
Remark: To assemble the Front Vertical Panel Cover-Lower, please make sure the attachment
points are in the correct position and no edge is protruding. Insert the screws slightly and if
all screws and the fairing are in the correct positions, then tighten them fully.
https://www.motorcycle-manual.com/
Altri manuali per VX-2
1
Indice
Altri manuali Vectrix Scooter
