Velleman K1803 Manuale utente
K1803
ILLUSTRATED ASSEMBLY MANUAL H1803IP'2
T ot al sold e r poi n ts: 29
Difficulty level: beginner 1 2 3 4 5 advanced
Thiskithasbeendevelopedaspre-modulefor
anumberofaudioapplicationswherethereis
insufficientinputsignal.Applicationsasa
microphonepre-amplifierorforlevelcorrection.
UNIVERSAL MONO PREAMPLIFIER
Specifications
Power supply: 10-30VDC / 10mA.
Output impedance: 1Kohm.
Adjustable output level: max. 40dB.
Frequency range: 20Hz to 20kHz ± 3dB.
Max. input signal: 40mV.
PCB dimensions: 30 x 40mm (1.2" x 1.57").
VELLEMAN NV
Legen Heirweg 33
9890 Gavere
Belgium Europe
www.ve llem an.be
www.velleman-kit.com
3
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it oft en on a wet s p onge or cl oth, t o k ee p it cl ean; th en ap ply sol de r t o t he ti p, t o gi ve it a wet look . Th is is c al le d ‘thinning’ and will
protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
• Thin raisin-core solder. Do not use any flux or grease.
• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
⇒Make sure the skill level matches your experience, to avoid disappointments.
⇒Follow the instructions carefully. Read and understand the entire step before you perform each operation.
⇒Perform the assembly in the correct order as stated in this manual
⇒Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒Values on the circuit diagram are subject to changes.
⇒Values in this assembly guide are correct*
⇒Use the check-boxes to mark your progress.
⇒Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.
0.
0
0
0
4
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
You will find the colour code for the resistances on our website: www.velleman.be
DO NOT BLINDLY FOLLOW THE ORDER OF THE
COMPONENTS ONTO THE TAPE. ALWAYS CHECK
THEIR VALUE ON THE PARTS LIST!
5
R1 : 100K (1 - 0 - 4 - B)
R2 : 100K (1 - 0 - 4 - B)
R3 : 100K (1 - 0 - 4 - B)
R4 : 100K (1 - 0 - 4 - B)
1. Resistors
R...
IC1 : 8p
2. IC socket, Watch the po-
sition of the notch!
AF IN (2 x)
AF OUT (2x)
Power (+)
Power (-)
4. PCB pins
Constructi o n
RV1 : 220K (250K)
6. Trim potentiometer
RV.. .
C1 : 10µF
C2 : 10µF
C3 : 10µF
C4 : 10µF
C5 : 10µF
5. Electrolytic capacitors.
Watch the polarity !
C...
IC1 : LM358
Pay attention
to the
position of
the notch!
7. IC mounting
R5 : 100K (1 - 0 - 4 - B)
R6 : 100K (1 - 0 - 4 - B)
R7 : 2K2 (2 - 2 - 2 - B)
3. Vertical resistors
R...
6
8. Connection
Conne c tion
Connect a stabilized supply between 10 and 30V with the points “+” and “-” on the print.
The input is connected on the points “AF IN”.
The output is taken on the connection “AF OUT” and the ground “-”.
To connect your in– and output you’d better use a screened wire, this to avoid interferences and rumble
With the trimmer RV1 you can control the output signal between 0 and max.
Connec tion e xa mple
Dyna mic mi crop hone
Telephone pick up coil
...
MAX. 40mV
To : Amplifier, Mixing
panel, Tape recorder, ...
10 ... 30VDC
INPUT
OUTPUT
7
9. Schematic diagram.
Schematic diagram & PCB
R4
100K
R3
100K
R2
100K
C1
10µ
GND
+V
C2
10µ
C5
10µ
SK1
AF IN
SK2
AF OUT
3
2
84
1
IC1A
5
6
7
IC1B
C3
10µ
C4
10µ
R7
2K2
R6
100K
R1
100K
R5
100K
RV1
220K
10. PCB
Modifications and typographical errors reserved
© Vellema n nv.
H1803IP - 2010 - ed.2
VELLEMAN NV
Legen Heirweg 33, 9890 Gavere
Belgium - Europe
5 410329 434977
Indice
Altri manuali Velleman Amplificatore
Velleman
Velleman HQ Power VPA2200MBN Manuale utente
Velleman
Velleman K8010 Manuale utente
Velleman
Velleman HQ Power ONELINER 100 Manuale utente
Velleman
Velleman HQ-Power VDSPROM7 Manuale utente
Velleman
Velleman 8040 Manuale utente
Velleman
Velleman HQ Power PAA01 Manuale utente
Velleman
Velleman High-Q K2572 Manuale utente
Velleman
Velleman HQ-POWER SAGIRA 100 Manuale utente
Velleman
Velleman HQ Power PAA04 Manuale utente
Velleman
Velleman VAS4A Manuale utente
Velleman
Velleman K8060 Manuale utente
Velleman
Velleman K4102 Manuale utente
Velleman
Velleman ARDUINO VMA408 Manuale utente
Velleman
Velleman K4040 Manuale utente
Velleman
Velleman High-Q Velleman-kit K8022 Manuale utente
Velleman
Velleman K4003 Manuale utente
Velleman
Velleman VD4C Manuale utente
Velleman
Velleman K4040 Manuale utente
Velleman
Velleman POWER BLOCK K8081 Manuale utente
Velleman
Velleman 8020 Manuale utente
