Velleman AER Domus Guida all'installazione

POWER SAVER / TIMER

K8075

ILLUSTRATED ASSEMBLY MANUAL H8075IP-1

Total solder points: 202

Difficulty level: beginner 12345 advanced

Turnsoffyourequipmentafterapresettime,it

helpsyousavemoneyanditincreasessafety

Assembly hints

The power saver turns off your equipment after a preset time. It helps you save money and it increases safety.

FEATURES:

 Single button operation with LED mode indicator

 continuous : 24h turn-off timer

 slow flashing : 4h or 8h turn-off timer

 fast flashing : 1h or 2h turn-off timer

 dim : idle

 Choose short or long-running timers (one-time jumper setting)

 10A suppressed relay output

 Easy to add to existing equipment

Applications: automatically turn off heating, cooling, lighting, entertainment systems, fans, pumps, sprin-

klers, etc...

SPECIFICATIONS:

 Available timers: 1h / 2h / 4h / 8h / 24h

 Relay output: 10A / 240VAC max

 Power supply: 100 - 240VAC

 Dimensions: 65 x 50 x 26mm

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will

protect the tip, and enables you to make goodconnections. When solder rolls off the tip,it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they

cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

⇒ Make sure the skill level matches your experience, to avoid disappointments.

⇒ Follow the instructions carefully. Read and understand the entire step before you perform each operation.

⇒ Perform the assembly in the correct order as stated in this manual

⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

⇒ Values on the circuit diagram are subject to changes.

⇒ Values in this assembly guide are correct*

⇒ Use the check-boxes to mark your progress.

⇒ Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.

Assembly hints

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

REMOVE THEM FROM THE TAPE ONE AT A TIME !

AXIAL COMPONENTS ARE TAPED IN THE

CORRECT MOUNTING SEQUENCE !

You will find the color code for the resistances on our website:

http://www.velleman.be/common/service.aspx

ZD...

CATHODE

D...

CATHODE

 R1 : 330K (3 - 3 - 4 - B - 9)

 R2 : 330K (3 - 3 - 4 - B - 9)

 R3 : 220 (2 - 2 - 1 - B - 9)

 R4 : 47K (7 - 7 - 3 - B)

 R5 : 1K (1 - 0 - 2 - B)

 R6 : 1K (1 - 0 - 2 - B)

 R7 : 10K (1 - 0 - 3 - B)

 R8 : 10K (1 - 0 - 3 - B)

 R9 : 10K (1 - 0 - 3 - B)

 R10 : 2K2 (2 - 2 - 2 - B)

 R11 : 6K8 (6 - 8 - 2 - B)

 R12 : 3K9 (3 - 9 - 2 - B)

5. Resistors

 IC1 : 8p

6. IC socket. Watch the

position of the notch!

Construction

 D1 : 1N4148

1. Diodes. Watch the polarity ! 4. Metal film resistors (1%)

R...

 ZD1 : 5V1/0.5W

 ZD2 : 24V/1.3W

2. Zenerdiodes. Watch the

polarity !

 D2 : 1N4007

 D3 : 1N4007

 D4 : 1N4007

 D5 : 1N4007

3. Diodes. Watch the polarity !

D...

CATHODE

R...

 C1 : 100nF (104)

 C2 : 100nF (104)

7. Capacitors.

c...

Construction

 SK6 : 4p

9. Board to wire connector

 JP1 : 2p

10. Pin header

Choose timer :

Mounted : 2h / 8h

Not mounted : 1h / 4h

11. Shunt

 VDR1: VDR300

13. VDR

 L

 N



12. PCB terminals

 T1 : BC547B

 T2 : BC547B

8. Transistors

AC power out

AC power in

 C3 : 100µF / 35V



C4 : 100µF / 35V

14. Electrolytic capacitors

Watch the polarity!

C...

Construction

Choose operation voltage :

230V :

 C5 : 0,47µF / 630V

115V :

 C5 : 0,68µF / 400V

15. Capacitor

 RY1 : VR10V241C

(24DC - 10A - 1contact)

16. Relays

 IC1 : VK8075

(programmed PIC10F200-I/PG)

17. IC. Watch the position of the notch!

 CHECK THOROUGHLY ALL THE COMPONENTS FOR MISS

MOUNTING, INCLUDING SOLDERING ERRORS.

 PUT AN EXTRA THICK LAYER OF SOLDER

ON THESE PCB TRACKS TO IMPROVE THEIR

CURRENT HANDLING CAPACITIES.

Fig. 1.0

 Cut off a piece of shrinkable tube with a lenght equal to 2,5cm.

 Slide the shrinkable tube over the wires of the female 'board to wire'-connector (fig. 2.0)

 Solder the 4-pole female 'board to wire' connector to the push button using the figure

below to check the accuracy of the connections (see figure 3.0)

 Attention: Always make sure to slide down the shrinking tube far enough from the soldering points!

 Slide the shrinkable tube over the soldered joints and heat them using a hair dryer or, better still, using a

paint stripper.

18. Wiring the push button

(Orange)

(Red)

(Yellow)

(Brown) Leen d :

LED -

LED +

Push button

Wiring the push button

Fig. 2.0

(Yellow)

(Orange)

(Brown) 2

(Red)

Fig. 3.0

Wiring the push button

 In case you want to use a different push button, make sure it is rated for the AC-voltage.

 If you do not use the included push button, you can mount a 3mm LED on the PCB.

COLOR= 2...5

LD...

CATHODE

Watch the polarity !

 Do not use both simultaneously

(LED & included push button)

Indice

Altri manuali Velleman Controllori

Velleman

Velleman HQ-Power HQRC10002 Manuale utente

Velleman

Velleman vellight CHLSC4 Manuale utente

Velleman

Velleman HQ Power VDPDMXC174 Manuale utente

Velleman

Velleman E305DC Manuale utente

Velleman

Velleman HQ POWER VDPC174 Manuale utente

Velleman

Velleman CAMCOLD/CK Manuale utente

Velleman

Velleman SOL4UCN2 Manuale utente

Velleman

Velleman TRCV3 Manuale utente

Velleman

Velleman VDP100TT Manuale utente

Velleman

Velleman VM192RF Manuale utente

Velleman

Velleman VMB2BL Manuale utente

Velleman

Velleman K2639 Manuale utente

Velleman

Velleman HQ-Power VDPDMXC146 Manuale utente

Velleman

Velleman CHLSC2 Manuale utente

Velleman

Velleman HQ POWER VDPDMXC144 Manuale utente

Velleman

Velleman TRCV2A Manuale utente

Velleman

Velleman VM162 Manuale utente

Velleman

Velleman HQRC10001 Manuale utente

Velleman

Velleman High-Q Velleman-kit K6000 Manuale utente

Velleman

Velleman VMA333 Manuale utente

Velleman

Velleman Vellight LEDC25 Manuale utente

Velleman

Velleman CHLSC1 Manuale utente

Velleman

Velleman SOL4UCN2 Manuale utente

Velleman

Velleman VMB2BL Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente