Velleman HAA2866 Manuale utente

D I G I TA L AC C E S S

CONTROL KEYPAD

3 OUTPUT RELAY

HAA2866

Programming & Installation Manual

FOR ELECTRIC LOCK, INTER-LOCK

AND SECURITY SYSTEM INSTALLATIONS

HAA2866

TABLE OF CONTENTS

INTRODUCTION

FEATURES

SPECIFICATIONS

INSTALLATION

Precautions

Package Contents

CONNECTION TERMINALS

The On-Board LED Indicators

The Pacifier Tones & The LED Signals

The Jumper for Back-Lit Selection

FEATURE PROGRAMMING & OPERATION INSTRUCTIONS

Set System in Programming Mode with The Master Code

Direct Access to Programming Mode with The “DAP” Code – 8 0 8 0

Refresh The System with The “Refreshing Code” --- 9 9 9 9

The Default Values of The Keypad

KEYPAD PROGRAMMING MAKE SIMPLE – For General Users

FEATURE PROGRAMMING -- KEY IN AND STORE THE DESIRED VALUES

Programming Criteria for Codes

Record A Master Code

Record A Super User PIN

Operation And Functions of The Super User PIN

Record The Common User PINs for Output 1, 2 & 3

Record-Delete PINs or Cards for Output 1, 2, & 3

Examples – Programming And Operation

Visitor Codes (For Output 1 Only)

Duress Codes (For Outputs 1, 2 & 3)

The Operation And Function of The Duress Code

Configuration of The Output Modes for Output 1, 2 And 3

Personal Safety And System Lock-Out

User PIN Entry Mode

Pacifier Tones On-Off Selection

Output Operation Announcer

Status LED Flashing On-Off during Standby

Door Forced Open Warning & Timing

Door Propped-Up Warning & The Delay Time

Intelligent Egress Button – An Unique Feature of A Contemporary Keypad

Where And Why “Going Out” Needs Attention

Egress Delay , Warning And Alarm

Configurations of The Egress Warning And Alarm

Door Opening Alarm & Timer

Close The Programming Mode

THE WIRE HARNESS FOR “WIEGAND DATA OUTPUT” & “APO DATA I/O”

...................................................................................4

........................................................................................4

.................................................................................5

....................................................................................6

.....................................................................................6

...............................................................................6

........................................................................7

.....................................................................9

.............................................................9

.................................................................9

.......................................10

..........................................10

................................10

........................................11

...............................................................11

....................................12

.........................14

.................................................................14

..........................................................................15

.......................................................................16

................................................16

...............................................16

.................................................17

......................................................18

...............................................................20

............................................................21

...............................................22

..........................................23

...........................................................23

...........................................................................24

..................................................................24

....................................................................24

......................................................25

............................................................25

.....................................................25

..........................26

...................................................26

...............................................................27

...............................................27

....................................................................28

..................................................................28

.........................29

Split-decoded Keypad System

The Wire Harness

The Operation Modes and The Wiegand Output

Wiegand Output at Keypad Operation Mode

TIMING & ELECTRICAL MANNER OF THE WIEGAND DATA OUTPUT

Diagram of The Wiegand Protocol Timing and Its Electrical Manner

THE 26 BIT WIEGAND DATA OUTPUT READING FROM THE EM CARDS

Example 1: Wiegand Output of Reading An EM Card

THE 34 BIT WIEGAND DATA OUTPUT READING FROM THE USER PINS

Example 2 : Wiegand Output from PIN / Code Entry

THE APO DATA I/O PORT -- FOR SETTING UP A SPLIT-DECODED KEYPAD

The Optional DA-2800 Controller --- Introduction

PROGRAMMING SUMMARY CHART

APPLICATION EXAMPLES

Basic Wirings of A Stand Alone Door Lock

Basic Wirings of A Stand Alone Door Lock with Inhibit Authorization Code

Basic Wirings of An Inter-Lock System Using Two Keypads

APPLICATION HINTS FOR THE AUXILIARY TERMINALS

APPENDIX

...................................................................29

..............................................................................29

..................................................30

....................................................30

..............................31

.................................31

...........................32

..............................................32

...........................33

...............................................33

........................34

..................................................34

..............................................................35

.......................................................................37

........................................................37

............................38

.........................................39

..........................................40

.......................................................................................43

VOOR VERPAKKINGEN

At the end of its life cycle, dispose of this product in accordance with local and national disposal

regulations. Read the manual thoroughly before bringing this device into service

Ontdoe u, ophet einde van zijn levensduur, van dit product volgens de plaatselijke en nationale

regelgeving inzake verwijdering. Lees deze handleiding grondig voor u het toestel in gebruik neemt.

A la fin de sa durée de vie, débarrassez-vous de ce produit en respectant la législation d'élimination

locale et nationale. Lisez le présent manuel attentivement avant la mise en service de l'appareil.

Tire las muestras inservibles en los correspondientes depósitos de eliminación de residuos según las

leyes locales y nacionales.Lea atentamente las instrucciones del manual antes de utilizar el aparato.

Entsorgen Sie dieses Produkt gemäß der örtlichen und nationalen Gesetzgebung bezüglich Entsorgung.

Lesen Sie diese Bedienungsanleitung vor Inbetriebnahme sorgfältig durch.

IN DE HANDLEIDINGEN

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised company for recycling.

This device should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Aan alle ingezetenen van de Europese Unie

Belangrijke milieu-informatie betreffende dit product

Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt weggeworpen, dit toestel schade kan

toebrengen aan het milieu.

Gooi dit toestel (en eventuele batterijen) niet bij het gewone huishoudelijke afval; het moet bij een gespecialiseerd bedrijf

terechtkomen voor recyclage.

U moet dit toestel naar uw verdeler of naar een lokaal recyclagepunt brengen.

Respecteer de plaatselijke milieuwetgeving.

Heeft u vragen, contacteer dan de plaatselijke autoriteiten inzake verwijdering.

Pour tous les résidents de l’Union européenne

Informations importantes sur la protection de l’environnement

Ce symbole figurant sur l’appareil ou sur l’emballage indique que l’élimination de l’appareil en fin de vie peut polluer

l’environnement.

Ne pas éliminer l’appareil (ou des batteries) avec des déchets non triés ; il doit être recyclé par une déchèterie.

Vous devez retourner l’appareil en fin de vie à votre distributeur ou à un service de recyclage local.

Il convient de respecter la réglementation locale relative à la protection de l’environnement.

En cas de doute, contactez les autorités locales.

Erratum p. 23

Section Configuration of the output modes on

page 23 contains an error and should be as

follows:

Set timing mode for output relay

Example of key combination to set the timing

mide for an output relay.

•The following key combination sets 20

seconds for location 1.

•The following key combination sets 10

minutes (600 seconds) seconds for location

INTRODUCTION

The HAA2866 is a self-contained three relay outputs, touch sensing weatherproof keypad. It combines

the functions of digital keypad and proximity EM card reader in one unit.

The HAA2866 employs a tact switch keyboard.

The HAA2866 can work independently as a stand alone keypad or works together with an optional

“APO controller” to form a high security split-decoded keypad system. It is also a card reader

providing of 26 bits Wiegand data output from reading of an EM Card and 34 bits data output from

the entry of an PIN/code. The Wiegand data can be used by consultants and end users when setting

product design or system installation criteria.

The keypad comes with plenty of functions for owner’s selection via programming. Owners can take

them freely to tailor the desired features for their system.

HAA2866 is an ideal keypad mainly for Door Strike and Alarm Arm-disarm control. It is also a

programmable industrial timer (with the timing of 1 second to over 24 hours) for Automatic Operator

systems.

The unit is designed for surface mounting on wall and its relay outputs are for Output 1, Output 2 and

Door bell.

FEATURES

A member of the Tri-Tech series keypads compatible with the optional APO Access Controller

Indoor or outdoor installation

Stand Alone or Inter-lock system built-in with all the required control logics

Controls “Going in” with PIN and/or Card; and “Going out” with programmable egress button

Tact Switch Keyboard (HAA2866)

Built-in Tamper Switch

Weatherproof (IP-55)

Data I/O port for Up-grading the system to Split-decoded operation with the optional “APO

Controller”

26 bit standard Wiegand data output from reading of EM cards

34 bit Wiegand data output on PIN / code entry

Outputs controlled by independent groups of codes / PINs / Cards

Programmable Timers for Door Strike, Alarm Arm-disarm Control or Industrial Automatic Operators

THE OPTIONAL CONTROLLERS FOR SPLIT-DECODED OPERATION

DA-2800 -- Full Feature Decoder + RF Remote Control

DA-2801 -- Full Feature Decoder

SPECIFICATIONS

Operating Voltage:

12V DC Nominal; 11-15V DC

Operating Current:

75mA (quiescent) to 140mA (three relays active)

Operation Temperature:

-20 C to +70 C

Environmental Humidity:

5-95% relative humidity non-condensing

Working Environment & Ingress Protection:

All weather, IP-55

Number of Users:

Output 1 – 1,000 (PINs and/or Cards) + 50 Duress Codes

Output 2 – 100 (PINs and/or Cards) + 10 Duress Codes

Output 3 – 100 (PINs and/or Cards) + 10 Duress Codes

Proximity Card:

Standard EM Card or Keyfob, 125Khz

Number of Visitor Codes:

50, programmable for one time or with the time limit

Timings for Code Entry and Card Reading:

10 seconds waiting for next digit entry

30 seconds waiting for code entry after card reading

The Timers:

Three 1-99,999 Seconds (Over 24 Hours possible) Independent Programmable Timers for O/P 1, 2

& 3

Egress Button:

Programmable for Instant, Delay with Warning and/or Alarm

Momentary or Holding Contact for the Exit Delay

Input Sensing Terminals:

a) Door position, b) Egress, c) O/P 1 inhibit

Output Control Terminals:

Transistor Open Collector 24VDC/100mA sink Max for the following outputs

a) Duress, b) Alarm, c) Key Active, d) Output 3, e) Inter-lock

Output Contact Ratings:

Output Relay 1 – N.C. & N.O. dry contacts, 5A/24VDC Max.

Output Relay 2 – N.C. & N.O. dry contacts, 1A/24VDC Max.

Door Bell Relay – N.O. dry contact, 1A/24VDC Max.

Tamper Switch – N.C. dry contact, 50mA/24VDC Max.

Dimensions:

129(H) X 83.5(W) X 41(D)mm

Weight:

220g net

Housing:

ABS Plastic box

Specifications are subject to change for modification without notice

INSTALLATION

HAA2866

PRECAUTIONS

1) Prevent Interference:

The EM Card reader is working at the frequency of 125Khz. Installation precautions are necessary.

i) Make sure the location for installation has no strong low frequency electro-magnetic wave signals.

Especially in the range of 100-200Khz

ii) If there is more than one keypads with the same operation frequency installed closely in the same

location, make sure that they are at least 60cm (2ft) apart from each other to prevention interference.

2) Prevent Accidental Short Circuit:

In the previous experience, most of the damages caused in the installation are accidental touching

of the components on circuit board with the wires carrying power. Please be patient to study the

manual to become familiar with the specifications of the system before starting the installations.

i) Do not apply power to the system while it is in installation.

ii) Check carefully all the wirings are correct before applying power to the system for testing.

PACKAGE CONTENTS

• One HAA2866 Keypad

• Two EM cards

• One pack of Mounting Screws

• One Hex Screw Wrench

• One Wire Harness ( Six wires)

• One Programming & Installation Manual

DER

REBMA

NEERG

FIXING SCREWS

Plastic Back Box

Faceplate

Faceplate Frame

CONNECTION TERMINALS

1 - 2 : 12V DC (Power Input Terminal)

Connect to 12V DC power supply. The (

) supply and the (

) GND are the common grounding points

of the system. The system accepts full input voltage range with no jumper selection.

3 - 4 - 5 : OUTPUT 1 (Output Relay 1)

5 Amp relay dry contact controlled by the Group 1 User PINs or Cards for Output 1, recommended for

door strike. Terminal 3 is Normally Closed (N.C.), terminal 5 is Normally Open (N.O.) and terminal 4 is

the common point of the two contacts. Use N.C. output for Fail-safe locking device; and N.O. output

for Fail-secure locking device. The relay is programmable for Start/Stop (toggle) mode or Momentary

timing mode. See programming Location 51 for the details.

6 - 7 : DOOR BELL (Output Relay Contact for Door Bell)

It is a Normally Open (N.O.) relay dry contact with maximum rating of 24VDC/1Amp. It is prepared as

a triggering contact of a low voltage door chime. The contact point keeps close as long as the bell

button on the keypad is pressed.

8 : EG IN ( Egress Input)

A Normally Open (N.O.) input terminal referring to (

) ground. With the help of connecting a normally

opened button to activate Output 1 for door opening in the same manner of using the Group 1 User

PINs or Cards.

Egress button is usually put inside the house near the door. More than one egress buttons can be

connected in parallel to this terminal. Leave this terminal open if not used.

See Programming Locations 90 and 91 for more information about the Egress Button with other

features.

9 - 10 - 11 : OUTPUT 2 (Output Relay 2)

1 Amp relay dry contact controlled by the Group 2 User PINs or Cards for Output 2, it is an auxiliary

output ideally for controlling security system or automatic operator. Terminal 9 is Normally Closed

(N.C.), terminal 11 is Normally Open (N.O.) and terminal 10 is the common point of the two

contacts. The relay is programmable for Start/Stop (toggle) mode or Momentary timing mode. See

programming Location 52 for the details.

KEY ALARM

FULL AUTO

BACK-LIT

WIEGAND

& DATA

K OR A JUMPER

BACK-LIT

JUMPER

CONNECTION

TERMINALS

WIEGAND

& DATA I/O

HARNESS

12 : OUTPUT 3 (NPN Transistor Open Collector Output)

An NPN transistor open collector output that is controlled by the Group 3 User PINs or Cards for

Output 3. It has the maximum power rating of 24VDC/100mA sink. It is equivalent to an N.O. (Normally

Open) terminal referring to ground. It can be used to drive small power device, such as a relay or a

low power control point of other equipment. This output point is programmable for Start/Stop (toggle)

mode or Momentary timing mode. See programming Location 53 for the details.

13 - 14 : TAMPER N.C. (Tamper Switch Normally Closed Contact)

A normally closed dry contact while the keypad is secured on its box. It is open while keypad is

separated from the box. Connect this N.C. terminal to the 24 hour protection zone of an alarm system

if necessary.

15 : DOOR SENS N.C. (Door Position Sensing Input -- Normally Close)

A Normally Closed (N.C.) sensing point referring to (

) ground, with the help of a normally closed

magnetic contact monitors the open or close status of the door. It initiates the following functions for

the system. Connect it with jumper to (

) Ground if not used.

a) Door Auto Re-lock

The system immediately re-locks the door after it is re-closed before the end of the programmed

time for output 1. It prevents unwanted “tailgate” entry.

b) Door Forced Open Warning

The keypad generates “door forced open” warning and alarm instantly once the door is forced

to open without a valid user PIN, Card or egress button. The warning lasts as long as the time

programmed (1

999 sec). It can be stopped with an User PIN or card for output 1 at anytime. See

programming Location 80 for the details.

c) Door Propped-up Warning

The keypad generates propped-up warning beeps (does not activates alarm output) while the door

is left open longer than the allowable time programmed. The warning will last as long as the door is

open until re-closed. See programming Location 81 for the details.

d) Inter-lock Control

The inter-lock control output always goes to (

) while the door is open, which gives signal to

disable the other keypad in the inter-lock system. See the Inter-lock terminal description for more

information.

e) Door Opening Alarm

Door Opening Alarm is designed for the emergency door only. It is always given when the door

is opened unless a valid user code or card is used prior to the door is opened. See programming

Location 91 for the details.

16 : (

) GND (Common Ground)

A grounding point of the keypad that is common to terminal 2.

17 : DU OUT (Duress Output)

An NPN transistor open collector output with the maximum power rating of 24VDC/100mA sink. It

is equivalent to an N.O. (Normally Open) terminal switching to (

) ground after the Duress Code is

entered. Use it to trigger an alarm zone of a security system, or turn on a buzzer to notify a guard.

18 : O/P 1 INHIBIT N.O. (Output 1 Inhibit Control Input – Normally Open)

A Normally Open (N.O.) sensing input point for controlling the Output 1, with this terminal connecting

to (

) ground, the Egress Button, the group of User PINs and Cards for Output 1 are all disabled.

It is prepared mainly for the cross wire connection with the “Inter-lock O/P” point on the other keypad

in an Inter-lock system.

NOTE: The inhibit function does not govern the Duress Codes and the Super User Codes. They are

always valid.

19 : INTER-LOCK O/P (Inter-lock Control Output)

An NPN transistor open collector output with the maximum power rating of 24VDC/100mA sink. It is

OFF at normal condition and it switches to (

) ground immediately for the first 5 seconds after keying

in a valid User PIN or reading a card to operate Output 1, then, it will keep tying to (

) ground during

the Door Position Sensor is open circuit due to door opening. Use this output point to make cross

wire connection with the other keypad’s “O/P 1 Inhibit” point in an Inter-lock system to prevent both

doors can be opened at the same time.

THE ON-BOARD LED INDICATORS

RED / GREEN (Right) ---

AMBER (Centre) ---------

RED (Left) ----------------

THE PACIFIER TONES & THE LED SIGNALS

The buzzer and the amber LED indicator give following tones and signals respectively for system

status:

STATUS TONES * LED SIGNALS

1) On Programming Mode ----- ON

2) Successful Key Entry 1 Beep 1 Flash

3) Successful Code / Card Entry 2 Beeps 2 Flashes

4) Unsuccessful Code / Card Entry 5 Beeps 5 Flashes

5) Power Up Delay Continuous Beeps Continuous Flashes

6) Output Relay Activation ** 1 Second Long Beep

7) On Standby *** ----- 1 Flash in 1 Second Interval

8) System Refreshing ----- Fast Flashes for 2.5 Minutes

9) Card or PIN Already Stored in

System

1 Long Beep -----

NOTE:

* *

* * *

THE JUMPER FOR BACK-LIT SELECTION

1) Full Back-lit ---

2) Auto Back-lit ---

An Inter-lock System:

An inter-lock system is a two-door system that always allows only one of the doors to open during

the operation. While one of the doors is opened, the other door keeps close until the open door is re-

closed. It prevents the unauthorized people dashing into a protected area while the doors are in use.

An inter-lock system needs two keypads and two door position sensing switches for the two doors.

20 : “K” OR “A” O/P (Keypad Active Output or Alarm Output)

An NPN transistor open collector output with the maximum power rating of 24VDC/100mA sink. It

is equivalent to an N.O. (Normally Open) terminal referring to ground. It can be used to drive small

power device, such as a relay or a low power control point for other equipment. This output point is

selectable to give Keypad Active Output or Alarm Output via the Selection of the “K or A” jumper.

a) Keypad Active Output (“K”) --- It switches to (

) ground for 10 seconds on each key touch. It

can be used to turn on light, CCTV camera, or buzzer to notify a guard. See Application Hints for

more information.

b) Alarm Output (“A”) --- It switches to (

) ground while Alarm occurs in order to trigger external

alarm to give notification at remote location.

It lights up in Green for Output 1 activation; and Red for Output 2

activation.

It flashes on Standby. It shows the system status in synchronization

with the beep tones. The standby flashing can be set to OFF in

programming. See Location 73 for the details.

It lights up while one of the outputs is inhibited. It is also the Wiegand

LED in reader mode

All Pacifier Tones can be ON or OFF through the programming option at Location 71

The Output Relay Activation beep can be selected through the programming option at Location 72

The Standby flashing can be ON or OFF through the programming option at Location 73

The keypad gives dim backlit on standby. It turns to full backlit when a key

button is pressed, then back to dim backlit 10 seconds after the last key button is

pressed.

The backlit is OFF on standby. It turns to full backlit when a key button is pressed,

then back to OFF 10 seconds after the last key button is pressed.

Indice

Altri manuali Velleman Tastiera

Velleman

Velleman HAA85WP Manuale utente

Velleman

Velleman PC50001 Manuale utente

Velleman

Velleman HAA2850 Manuale utente

Velleman

Velleman CTC1000KP Manuale utente

Velleman

Velleman HAA2890 Manuale utente

Velleman

Velleman etiampro HAA2866N Manuale utente

Velleman

Velleman HAA85 Manuale utente

Velleman

Velleman HAA263D Manuale utente

Velleman

Velleman HAA9350 Manuale utente

Velleman

Velleman VMA300 Manuale utente

Velleman

Velleman PCUSB29 Manuale utente

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo