Ventev BTRM300 Manuale utente

Ventev 10999 McCormick Road, Hunt Valley, MD 21031

LIT SKU: 09834 | Rev: 062321

USER GUIDE FOR

BTRM300 & BTRM400

Battery Test Remote Monitor

[email protected] / 800-851-4965

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

Contents

1. Warnings ................................................................................................................... 4

1.1 BTRM300 ................................................................................................................................... 4

1.2 BTRM400 ................................................................................................................................... 4

2. Supplied Equipment ................................................................................................. 4

3. Overview ................................................................................................................... 4

4. System Description .................................................................................................. 5

4.1 BTRM300 & BTRM400 Overall System Diagram ...................................................................... 5

4.2 System Connector Overview ..................................................................................................... 5

5. Basic Setup ............................................................................................................... 6

5.1 Connecting Unit to a PC ............................................................................................................ 6

5.2 Accessing your host computer’s network settings ..................................................................... 7

5.3 Setting IP Address Information for BTRM Default ..................................................................... 8

5.4 Verify IP Address Information .................................................................................................... 8

5.4.1 For Wi-Fi Connections ...................................................................................................... 9

5.4.2 For Ethernet Connection .................................................................................................. 9

6. Mounting ................................................................................................................. 11

6.1 Wiring Battery Connection ....................................................................................................... 11

6.2 Wiring Power Supply Connections .......................................................................................... 11

6.3 Wiring Battery Charger Connections ....................................................................................... 11

6.4 Alarm Connections .................................................................................................................. 11

6.5 Clearing Battery Test Data ...................................................................................................... 11

7. Web Interface Menus ............................................................................................. 11

7.1 System Status Page ................................................................................................................ 12

7.2 Battery Status Page ................................................................................................................. 14

7.3 Battery Test Page .................................................................................................................... 15

8. Manual Test Page ................................................................................................... 16

8.1 Capacity IO Check ................................................................................................................... 16

8.2 Reset Battery Data and Setting to Defaults ............................................................................. 16

9. Port Options Page .................................................................................................. 17

9.1 IO Test 1 .................................................................................................................................. 17

9.2 IO Test 2 .................................................................................................................................. 18

9.3 Email Configuration Page ........................................................................................................ 18

9.4 Email Test Page ...................................................................................................................... 19

9.5 Network Configuration Page .................................................................................................... 20

10. DNP3 and Modbus RTU Configuration Page ..................................................... 21

10.1 Modbus Addressing ............................................................................................................... 21

10.2 SNMP Configuration Page ..................................................................................................... 23

10.3 Help Page .............................................................................................................................. 24

10.4 Authorization Page ................................................................................................................ 25

10.5 About ..................................................................................................................................... 26

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

11. SNMP Functionality .............................................................................................. 27

11.1 Install MIB Browser ................................................................................................................ 27

11.2 Install SNMP MIB File ............................................................................................................ 27

11.3 View BTRM via MIB Browser ................................................................................................. 28

11.4 Configure Trap Receiver ........................................................................................................ 30

11.5 Cannot Bind to Port 162 Error Message ................................................................................ 31

11.6 Open Trap Receiver .............................................................................................................. 33

12. Additional Protocols ............................................................................................ 36

DNP3 ............................................................................................................................................. 36

12.1 Overview ................................................................................................................................ 36

12.2 Data Link Layer ...................................................................................................................... 36

12.3 Application Layer ................................................................................................................... 36

12.3.1 Function Support .......................................................................................................... 36

12.3.2 Enable Disable Unsolicited Event Status ..................................................................... 37

12.3.3 Groups and Variations .................................................................................................. 37

12.3.4 Qualifiers ...................................................................................................................... 37

12.3.5 Binary Input Status Points ............................................................................................ 37

12.3.6 Analog Input Status Points ........................................................................................... 38

12.3.7 Analog Output Status Points ........................................................................................ 38

12.3.8 Binary Output Status Points ......................................................................................... 39

12.3.9 Binary Output Write to Points ....................................................................................... 39

12.3.10 Events ........................................................................................................................ 40

13. Modbus Protocols ................................................................................................ 40

Overview ........................................................................................................................................ 40

13.1 Function 01 Boolean (Coils) | Read Discrete Inputs .............................................................. 40

13.2 Function 02 Input Status | Read Discrete Inputs ................................................................... 41

13.3 Function 03 Holding Registers | Read Single or Multiple ...................................................... 41

13.4 Function 04 Input Registers | Read Single or Multiple ........................................................... 41

13.5 Function 05 Boolean (Coils) | Write Discrete Output ............................................................. 41

13.6 Function 06 Holding Register | Write Single .......................................................................... 42

14. Additional Network Setup .................................................................................... 42

14.1 IP Reset ................................................................................................................................. 42

14.2 Router Ports ........................................................................................................................... 42

14.3 Port Table .............................................................................................................................. 43

15. Specifications and Warranty ............................................................................... 43

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

1. Warnings

Carefully observe proper DC polarities connections for batteries, chargers, and loads.

*** Unit WILL be damaged by incorrect polarity connections ***

1.1. BTRM300

Maximum rated Voltages for Battery, Charger, Power Supply, and Loads is 30 VDC

Maximum rated Current for Battery, Chargers, Power Supply and Total Load is 20 Amps

*** Unit can be damaged by exceeding these limits ***

*** Use of an Inline fuse is recommended to prevent over current conditions***

1.2. BTRM400

Maximum rated Voltages for Battery, Charger, Power Supply, and Loads is 60 VDC

Maximum rated Current for Battery, Chargers, Power Supply and Total Load is 10 Amps

Alarm Connections CH1, CH2, CH3, CH4 rated for 60 VDC, 80ma max load.

• Observe correct polarity

• Do not exceed these ratings.

• Do not connect to AC line powered loads.

*** Unit can be damaged by exceeding these limits ***

*** Use of an Inline fuse is recommended to prevent over current conditions***

2. Supplied Equipment

Included in box:

• BTRM300 (Tessco SKU 281170) or BTRM400 (Tessco SKU 246962)

• 3ft Ethernet Cable

• BTRM User Guide

3. Overview

As batteries age their capacity slowly deteriorate until they need replacement. Additionally, battery

capacity can be affected by extended operation under adverse conditions of high or low

temperatures, high discharge rates, under charging (in particular if left in a completely discharged

state for weeks or longer), charging voltages higher than recommended (this condition immediately

starts generating surplus hydrogen gas for which even Sealed Lead Acid Batteries are forced to

vent).

Although a battery’s state of charge can be inferred by monitoring the battery terminal voltage while in

standby mode, this voltage will not give an indication of actual capacity. Furthermore, a battery that is

marginal may not be detected until it is called upon to perform, at which point it is too late to prevent a

system failure. For a battery connected to a charger that maintains a float voltage, neither condition

can be checked.

In these cases, the BTRM is designed to evaluate battery capacity transparently to system operation

and provide network-based notification should a battery fail, or its capacity drop below a specified

level. This also has the advantage of allowing batteries that exceed their nominal lifetime to remain in

service, provided they meet capacity requirements.

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

4. System Description

BTRM300 & BTRM400 Overall System Connection Diagram

System Connection Overview

4.1. Power Supply (+/-)

The BTRM must be connected to the load Power Supply in order to energize the load while

the Battery Charger is charging the battery. In the above figure, a separate Load Power

Source and Battery Charger are used. Alternatively, a single Power Source can be used. In

this case the Charger + and Power Supply + terminals must be connected together.

4.2. Battery Charger (+/-)

The BTRM must be connected to the battery charger in order to charge the battery bank

after the battery capacity test is performed.

4.3. Battery (+/-)

BTRM300 Allowable system voltages: 12V/24 (Max 32V)

IO Channel 1 +

IO Channel 1 -

IO Channel 2 +

IO Channel 2 -

Battery +

Charger +

Power Supply +

Battery -

Charger -

Power Supply -

Load +

Load -

RJ45

Fuse

BATTERY BANK

+ POS- NEG

SDR-120-12

DC OK

+V-V

+V ADJ

DC OK

3 State

Charger

DC OK

+V-V

Ready

System

Load

- NEG Pos+

Float

BTRM300

25 Amp

To AC source

BTRM400

15 Amp

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

BTRM400 Allowable system voltages: 12V/24V/36V/48V (Max 60V).

Remember to select BTRM operation voltage on the Port Options page or selecting via one

of the supported protocols (DNP3/Modbus/Snmp) for proper operation.

The battery bank must be connected directly to the BTRM, such that the BTRM can power

the load from the Battery without any additional power source in circuit in order to perform

the battery capacity test.

4.4. Load (+/-)

The battery bank must be connected directly to the BTRM in order to perform the battery

capacity test.

4.5. Alarm Connector (+/-)

BTRM300 & BTRM400 have 4 Channels of ground referenced IO.

All 4 channels can be used to sense and monitor 0V to 60V.

Channels 1 and 2 can be used to activate relays, audible indicators, or lamps by pulling the

IO pin to ground under certain alarm conditions.

Both Channels 1 and 2 contacts are normally open when power is off. The user can select

normally open or normally closed under an alarm condition.

Do not exceed the contact maximum relay ratings of 60 Volts, 80 ma. Do not use to directly

operate AC line connected equipment.

5. Basic Setup

Connecting unit to a PC

Notes on accessing a BTRM over Ethernet: Technically you should be able to plug the device into

your current network, regardless of how your current network IP addressing is set up and be able to

reach the BTRM’s Status and Setup web page by entering its IP address (found on the BTRM front

label) in a Web Browser on a local computer. However, in practice, not so easy, due to a wide variety

of possibly incompatible network addressing and firewall configurations. These difficulties occur most

often if someone else has set up the network settings, and in particular where these settings are

“managed” by software installed on your computer by your internet provider or corporate IT

departments.

To avoid these potential network issues at the initial evaluation stage it is best to connect both your

computer and the device to a hub/network switch (one that is not connected to the rest of your

network) or directly connect your computer to the BTRM with a cross-connected Ethernet cable.

Initial Power up to set IP address

To power up the device, connect the battery to the BTRM. Power up the power supply and battery

charger. The BTRM starts in self-test mode for 5 to 15 seconds. PB1 and PB2 push button LEDs will

blink.

Once the device is power up and cabled to the Ethernet, the GREEN LED will illuminate on the

Ethernet connector and startup should be complete within 30 sec.

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

Accessing your host computer’s network settings

From the start button select Control Panel -> Network and Internet -> Network Connections

• Select the adapter that you plan to use and from the File menu, select properties.

• This will bring up the properties window, shown on the right.

• Scroll down to the Internet Protocol Version 4 (IPv4) item, select it, and then select “properties”.

• This will bring up the window to allow manual configuration of the network adapter’s IP addresses.

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

Setting IP address information for BTRM default

Using a direct connection to the device with a cross connected cable or using a network switch (hub),

use the manual IP settings shown on the right. This property dialog can be found in the TCP/IP

properties, which is a sub dialog of the Network Connections Properties, both found in Control Panel

Network Connections.

(Typically, the default gateway and DNS server need not be entered.)

If using a router, check your local area connection settings to see if the router gateway address is the

same as the default device gateway of 192.168.1.1. If it’s not, you will need to use a direct connection

as described above to change the device gateway address to match the router’s gateway address.

Verify IP address information

For the initial configuration of the BTRM and to change Network IP settings for placement in an IP

based network you will need to connect the BTRM directly to your PC. Once connected to your PC

you will be able to configure the BTRM to match your network settings.

You will need the following information from your network administrator to add the BTRM to your IP

Network:

• IP Address – we recommend using a static IP address for the BTRM

• Gateway – what is the IP address of the Gateway of your network

• Subnet Mask – what is the mask of your network

• Primary DNS – IP address of the primary DNS server for your network

Once you have your connection made with laptop or PC you will need to record your IP address and

verify connection to the BTRM.

NOTE: It may be necessary to give your PC or Laptop a static address to access the BTRM default

network.

Example: IP Address: 192.168.1.200

Subnet mask: 255.255.255.0 Finding your IP address in Windows 10

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

For Wi-Fi connection

On the taskbar, select the Wi-Fi network icon

• Under the Wi-Fi network you're connected to, select Properties.

Under Properties, look for your IP address listed next to IPv4 address.

For Ethernet connection

On the taskbar, select the Ethernet network icon

1. Select the Ethernet network connection

2. Under Ethernet, select the Ethernet network connection.

3. Under Properties, look for your IP address listed next to IPv4 address.

Verify connectivity to the BTRM by sending a Ping command to the BTRM’s default IP address: PING

192.168.1.214 <Enter> you should receive four REPLY messages from the BTRM.

BTRM Battery Test Remote Monitoring System – User Guide V3.2 | ã2021 Ventev | LIT SKU: 09834

Command window available from Windows 10 by searching for cmd.exe

Open a New Web Browser Session (Microsoft Edge, Firefox, Chrome) and type in the address of the

BTRM (default is 192.168.1.214) and click <Enter>.

If everything is set up correctly you should see the System Status of the BTRM.

Note: The Green Status Indicator should be blinking when the BTRM is active and connected.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ventev Monitor

Ventev

Ventev BTRM200 Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione